|
|
| (не показано 16 промежуточных версий 2 участников) |
| Строка 1: |
Строка 1: |
| | | <languages/>{{DISPLAYTITLE: Hardware revisions of the Wiren Board controller}} |
| == The definition of the revision ==
| | *[[WB5_hardware_revisions | Hardware revisions of the Wiren Board 5]] |
| [[Файл:Wiren_Board_6.5_SIM.png|300px|thumb|right|Wiren Board rev.6.5 controller. Micro SIM 1 slot was moved to the front row of terminals]][[File:WB5 rev 5.8 front.png|300px|thumb|right|Wiren Board 5 rev. 5.8]][[File:WB5 rev 5.6.1 front.png|300px|thumb|right|Wiren Board 5 rev. 5.6.1]]In the latest firmware revision can be viewed in the web interface of the controller, under Devices => System, channel system/HW Revision. To programmatically determine the revision of the controller is possible via [[MQTT/en| MQTT]]. If there is no such section in the interface, the controller can be identified by marking on the bottom side of the Board (under the cover on the side of the DIN rail).[[File:WB5 main.jpg|300px|thumb|right|Wiren Board 5 rev. 5.3]]
| | *[[WB6_hardware_revisions | Hardware revisions of the Wiren Board 6]] |
| | | *[[WB7_hardware_revisions | Hardware revisions of the Wiren Board 7]] |
| == Wiren Board 6 revisions ==
| |
| {| class="wikitable"
| |
| !Revision
| |
| !Release date
| |
| !Identification
| |
| !Features
| |
| !Firmware version
| |
| !Interface revision
| |
| |-
| |
| |6.5
| |
| |12.2018
| |
| |Inscription r.6.5 on the bottom side of the board, the version in the interface
| |
| |
| |
| *Radiomodule is missing
| |
| *SIM card 1 is located in the lower left corner.
| |
| *Allowable supply voltage increased up to 48V.
| |
| * Power UVLO (6,9-7,7В)
| |
| |62 ???
| |
| |6.5 ??
| |
| |-
| |
| |6.4.1
| |
| |10.2018
| |
| |Inscription r.6.4.1 on the bottom side of the board, the version in the interface
| |
| |
| |
| |61
| |
| |6.4.1
| |
| |-
| |
| |6.4
| |
| |09.2018
| |
| |Inscription r.6.4 on the bottom side of the Board, the version in the interface
| |
| |
| |
| * New USB-UART chip supporting standard CDC class, on [[WB Debug Console/en| Debug Console]]
| |
| * USB port protection of the debug console from ESD | |
| * Detachable screw terminals
| |
| * Removed indication modem (NETLIGHT) for the led near the antenna of GSM
| |
| * Fixed bug [[WB 6: Errata/en|0630001]]
| |
| |61
| |
| |6.4
| |
| |-
| |
| |6.3
| |
| |02.2018
| |
| |Inscription Wiren Board 6 r.6.3 on the bottom side of the board.
| |
| | |
| |
| |
| |61
| |
| |6.3
| |
| |-
| |
| | |
| |}
| |
| | |
| == Differences between Wiren Board 6 and Wiren Board 5 ==
| |
| | |
| {| class="wikitable"
| |
| !Overall change
| |
| !Added
| |
| !Removed
| |
| |-
| |
| |
| |
| * Other processor - i.MX 287 was replaced by i.MX 6ULL. Now it is 800MHz Cortex A7 with mathematical coprocessor.
| |
| * Increased the RAM from 128 to 512MB
| |
| * Changed connectors for expansion modules. On the base Board connectors type "mom", added the key on the headscarves modules.
| |
| * The connector for the backup power modules has been changed.
| |
| Expansion modules and backup power for Wiren Board 5 is not suitable for Wiren Board 6.
| |
| |
| |
| * Third expansion connector for modules that do not require external terminals.
| |
| * Support for the second SIM card (there is one SIM card in the network at the same time )
| |
| * Output short-circuit protection A1-A4
| |
| * Temperature sensor on the base Board (sysfs)
| |
| * separate RTC
| |
| |
| |
| |} | |
| | |
| == Wiren Board 5 revisions ==
| |
| | |
| | |
| | |
| {| class="wikitable"
| |
| !Revision
| |
| !Release date
| |
| !Identification
| |
| !Differences from previous revision
| |
| !Revision in the interface
| |
| |-
| |
| |5.9
| |
| |
| |
| |
| |
| |Added separate hardware RTC (non-volatile clock)
| |
| |58
| |
| |-
| |
| |5.8.1
| |
| |
| |
| |
| |
| |
| |
| * Added second Ethernet port
| |
| * Changed power supply circuit: input power range extended to 5-28V<!-- 50V -->
| |
| * Removed the S/PDIF Toslink connector (it is possible to connect the connector to the pin connector on the Board)
| |
| * Removed port for IR transceiver (will be available as extension module)
| |
| * Debug console output to micro-USB interface instead of UART
| |
| * Added terminal strip for resver power input
| |
| | |
| Other:
| |
| | |
| <!-- * Improved USB protection: ferrite beads on + TVS lines.
| |
| * Static discharge protection on I2C lines on the I / o connector
| |
| * SIM chip can be installed on request -->
| |
| * On request is possible to install a 3G instead of 2G
| |
| | |
| |58
| |
| |-
| |
| |5.6.1
| |
| |
| |
| |Inscription Wiren Board 5 r.6.1 on the bottom side of the PCB
| |
| |
| |
| * The IR port is made small resistors and decoupling from the DC capacitor
| |
| |55
| |
| |-
| |
| |5.6
| |
| |04.2016
| |
| |Inscription Wiren Board 5 r.6 on the bottom side of the PCB.
| |
| | |
| Отсутствие клеммника R2
| |
| |
| |
| * Убран клеммник R2
| |
| * Добавлен клеммник Vout - выход напряжения питания
| |
| * Добавлены джамперы для включения терминирующих резисторов на линиях RS-485/CAN
| |
| * Отладочный UART перенесён к разъёму USB
| |
| * Улучшена стабильность работы в режиме восстановления прошивки через microUSB
| |
| * Режим перепрошивки активируется кнопкой FW, вместо джампера
| |
| * Питание с боковых модулей ввода-вывода не снимается при перезагрузке устройства по сторожевому таймеру
| |
| * Добавлен разъём MOD3 для подключения мезонинного модуля дисплея
| |
| * Добавлена поддержка второго USB-host в комплектации без Wi-Fi (комплектуется по запросу)
| |
| |55
| |
| |-
| |
| |5.3
| |
| |11.2015
| |
| |Надпись Wiren Board 5 r.3 на нижней стороне печатной платы.
| |
| | |
| Наличие клеммников R1 и R2
| |
| |
| |
| |52
| |
| |}
| |
| | |
| == Отличия Wiren Board 5 от Wiren Board 4 ==
| |
| | |
| | |
| {| class="wikitable"
| |
| !Общие изменения
| |
| !Добавлено
| |
| !Убрано
| |
| |-
| |
| |
| |
| * Другой процессор - IMX233 заменили на IMX287. Новый процессор полностью программно совместим с предыдущим.
| |
| * Увеличился объем RAM, с 64 до 128Мб
| |
| |
| |
| * Bluetooth low energy (BLE)
| |
| * порт CAN
| |
| * CIR (инфракрасный порт)
| |
| * S/PDIF (цифровой звук)
| |
| * разъем для двух модулей расширения
| |
| * разъем для боковых модулей ввода-вывода.
| |
| |
| |
| * Аудио джек 3,5 (стерео)
| |
| * Изолированный RS-485 (доступен как модуль расширения)
| |
| * Отдельные входы для сухих контактов (возможно подключение к универсальным входам AD-входам, также доступен модуль расширения)
| |
| * Реле (доступен модуль расширения и Модули ввода-вывода))
| |
| * Зарядка Li-Ion аккумулятора (доступно как опция)
| |
| |}
| |
