Disassembling the controller case/en: различия между версиями

Материал из Wiren Board
(Обновление для соответствия новой версии исходной страницы.)
Строка 1: Строка 1:
<languages/>
<languages/>
<div class="mw-translate-fuzzy">
{{DISPLAYTITLE: Disassembling the controller case }}
{{DISPLAYTITLE: Disassembling the controller case }}


Строка 7: Строка 8:
===Disassembling===
===Disassembling===
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case.
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case.
</div>


'''Step 1'''. Place the controller with the back cover up.
# Положите контроллер задней крышкой кверху.
 
# Вставьте отвертку между защелкой и основанием. Плавным вращательным движением отогните защелку и потяните заднюю крышку вверх. Проделайте тоже самое с остальными защелками.
'''Step 2'''. Insert a screwdriver between latch №1 and base. With a smooth twisting motion, bend the latch and pull the back cover up. Do the same with latch №2.
# С помощью отвертки отогните оставшиеся защелки и снимите крышку.
 
# Слегка отогните боковую стенку корпуса в месте, где расположен разъем для подключения внешних модулей, и вытолкните плату контроллера из корпуса. Не прилагайте больших усилий, чтобы не повредить разъем.
'''Step 3'''. Use a screwdriver to bend the remaining latches and get the cover.
 
'''Step 4'''. Slightly bend the side wall of the case in the place where the connector for connecting external modules is located, and push the controller board out of the case. Do not use too much force to avoid damaging the connector.


<div class="mw-translate-fuzzy">
<gallery mode="packed" heights="150px">
<gallery mode="packed" heights="150px">
Image: 4_latches.png | Step 1
Image: 4_latches.png | Step 1
Строка 22: Строка 22:
Image: Case5.jpg | Step 4
Image: Case5.jpg | Step 4
</gallery>
</gallery>
</div>


=== Assembly ===
=== Assembly ===
Assembly is carried out in the reverse order.  
Assembly is carried out in the reverse order.  


<div class="mw-translate-fuzzy">
'''Step 1'''. Place the controller board in the case.
'''Step 1'''. Place the controller board in the case.
</div>


'''Step 2'''.
<div class="mw-translate-fuzzy">
Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
 
'''Step 3'''. Easily bend the side wall near the connector housing for connecting side modules. With a light insertion, press the pulp into the housing so that the connector enters the opening in the side wall of the housing.
 
'''Step 4'''. Install the back cover. Lid latches should click into place.
 
<gallery mode="packed" heights="150px">
<gallery mode="packed" heights="150px">
Image: Case6.jpg | Step 1
Image: Case6.jpg | Step 1
Строка 41: Строка 38:
Image: Case8.jpg | Step 4
Image: Case8.jpg | Step 4
</gallery>
</gallery>
</div>


===Cover removing===
===Cover removing===
It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid.
It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid.


<div class="mw-translate-fuzzy">
'''Step 1'''. Lay the controller face up.
'''Step 1'''. Lay the controller face up.
</div>


'''Step 2'''. Pry out the latches on the controller cover with a flathead screwdriver.
<div class="mw-translate-fuzzy">
 
'''Step 3'''. Remove the cover.
 
<gallery mode="packed" heights="160px">
<gallery mode="packed" heights="160px">
Image: Cover_rem1.jpg | Step 1
Image: Cover_rem1.jpg | Step 1
Строка 56: Строка 53:
Image: Cover_rem3.jpg | Step 3
Image: Cover_rem3.jpg | Step 3
</gallery>
</gallery>
</div>

Версия 16:55, 17 августа 2022

Другие языки:


Tools

To disassemble the controller, you will need a slotted screwdriver.

Disassembling

To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case.

  1. Положите контроллер задней крышкой кверху.
  2. Вставьте отвертку между защелкой и основанием. Плавным вращательным движением отогните защелку и потяните заднюю крышку вверх. Проделайте тоже самое с остальными защелками.
  3. С помощью отвертки отогните оставшиеся защелки и снимите крышку.
  4. Слегка отогните боковую стенку корпуса в месте, где расположен разъем для подключения внешних модулей, и вытолкните плату контроллера из корпуса. Не прилагайте больших усилий, чтобы не повредить разъем.

  • Step 1

  • Step 2

  • Step 3

  • Step 4

Assembly

Assembly is carried out in the reverse order.

Step 1. Place the controller board in the case.

  • Step 1

  • Step 2

  • Step 3

  • Step 4

Cover removing

It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid.

Step 1. Lay the controller face up.

  • Step 1

  • Step 2

  • Step 3

Источник — https://wirenboard.com/wiki/index.php?title=Disassembling_the_controller_case/en&oldid=66444