Disassembling the controller case/en: различия между версиями
Matveevrj (обсуждение | вклад) |
FuzzyBot (обсуждение | вклад) (Обновление для соответствия новой версии исходной страницы.) |
||
| Строка 8: | Строка 8: | ||
To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of the controller from the case: | To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of the controller from the case: | ||
<div class="mw-translate-fuzzy"> | |||
# Place the controller back cover up. | # Place the controller back cover up. | ||
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | ||
# Use a screwdriver to bend back the remaining latches and take off the cover. | # Use a screwdriver to bend back the remaining latches and take off the cover. | ||
# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector. | # Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector. | ||
</div> | |||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
| Строка 20: | Строка 22: | ||
</gallery> | </gallery> | ||
<div class="mw-translate-fuzzy"> | |||
=== Assembly === | === Assembly === | ||
Assembly is carried out in the reverse order. | Assembly is carried out in the reverse order. | ||
</div> | |||
#Place the controller board in the case. | #Place the controller board in the case. | ||
| Строка 35: | Строка 39: | ||
</gallery> | </gallery> | ||
<div class="mw-translate-fuzzy"> | |||
===Cover removing=== | ===Cover removing=== | ||
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the cover. | It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the cover. | ||
</div> | |||
<div class="mw-translate-fuzzy"> | |||
#Place the controller face up. | #Place the controller face up. | ||
#Pry the latches on a front cover open with the slotted screwdriver. | #Pry the latches on a front cover open with the slotted screwdriver. | ||
#Take off the cover. | #Take off the cover. | ||
</div> | |||
Установка: | |||
# Положите контроллер лицевой стороной вверх. | |||
# Проденьте переключатель питания контроллера в отверстие на крышке. | |||
# Аккуратно защёлкните все защёлки. | |||
<gallery mode="packed" heights="160px"> | <gallery mode="packed" heights="160px"> | ||
Версия 09:00, 19 августа 2022
Tools
To disassemble a controller, you will need a slotted screwdriver.
Disassembling
To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of the controller from the case:
- Place the controller back cover up.
- Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches.
- Use a screwdriver to bend back the remaining latches and take off the cover.
- Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector.
Latches
Removing the back cover
Back cover removed
Removing the circuit board
Assembly
Assembly is carried out in the reverse order.
- Place the controller board in the case.
- Make sure the On/Off switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
- Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case.
- Install the back cover. The cover latches should close whith a clicking sound.
Circuit board installation
Front panel switch
Installing the connector in the aperture
Cover installed
Cover removing
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the cover.
- Place the controller face up.
- Pry the latches on a front cover open with the slotted screwdriver.
- Take off the cover.
Установка:
- Положите контроллер лицевой стороной вверх.
- Проденьте переключатель питания контроллера в отверстие на крышке.
- Аккуратно защёлкните все защёлки.
Front cover
Latches
Front cover removed
