wb_editors
14 355
правок
Disassembling the controller case/en: различия между версиями
Disassembling the controller case/en (просмотреть исходный код)
Версия 09:00, 19 августа 2022
, 1 год назадОбновление для соответствия новой версии исходной страницы.
Matveevrj (обсуждение | вклад) |
FuzzyBot (обсуждение | вклад) (Обновление для соответствия новой версии исходной страницы.) |
||
| Строка 8: | Строка 8: | ||
To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of the controller from the case: | To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of the controller from the case: | ||
<div class="mw-translate-fuzzy"> | |||
# Place the controller back cover up. | # Place the controller back cover up. | ||
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | ||
# Use a screwdriver to bend back the remaining latches and take off the cover. | # Use a screwdriver to bend back the remaining latches and take off the cover. | ||
# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector. | # Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector. | ||
</div> | |||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
| Строка 20: | Строка 22: | ||
</gallery> | </gallery> | ||
<div class="mw-translate-fuzzy"> | |||
=== Assembly === | === Assembly === | ||
Assembly is carried out in the reverse order. | Assembly is carried out in the reverse order. | ||
</div> | |||
#Place the controller board in the case. | #Place the controller board in the case. | ||
| Строка 35: | Строка 39: | ||
</gallery> | </gallery> | ||
<div class="mw-translate-fuzzy"> | |||
===Cover removing=== | ===Cover removing=== | ||
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the cover. | It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the cover. | ||
</div> | |||
<div class="mw-translate-fuzzy"> | |||
#Place the controller face up. | #Place the controller face up. | ||
#Pry the latches on a front cover open with the slotted screwdriver. | #Pry the latches on a front cover open with the slotted screwdriver. | ||
#Take off the cover. | #Take off the cover. | ||
</div> | |||
Установка: | |||
# Положите контроллер лицевой стороной вверх. | |||
# Проденьте переключатель питания контроллера в отверстие на крышке. | |||
# Аккуратно защёлкните все защёлки. | |||
<gallery mode="packed" heights="160px"> | <gallery mode="packed" heights="160px"> | ||