Disassembling the controller case/en: различия между версиями

Материал из Wiren Board
(Новая страница: «# Put the back cover controller up. # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with professional latches. # Use a screwdriver to bend the remaining latches and get the cover. # Lightly bend the side wall of the case where the connector for connecting external modules is located, and push the controller connector out of the case. He did not become high-r...»)
Метки: правка с мобильного устройства правка из мобильной версии
(Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.»)
 
(не показаны 33 промежуточные версии 3 участников)
Строка 1: Строка 1:
<languages/>
<languages/>
<div class="mw-translate-fuzzy">
{{DISPLAYTITLE: Disassembling the controller case }}
===Tools===
===Tools===
To disassemble the controller, you will need a slotted screwdriver.
To disassemble the controller, you will need a slotted screwdriver.


===Disassembling===
===Disassembling===
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case.
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case:
</div>


# Put the back cover controller up.
# Place the controller back cover up.
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with professional latches.
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches.
# Use a screwdriver to bend the remaining latches and get the cover.
# Use a screwdriver to bend back the remaining latches and take off the cover.
# Lightly bend the side wall of the case where the connector for connecting external modules is located, and push the controller connector out of the case. He did not become high-ranking, so as not to attract attention.
# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB.


<div class="mw-translate-fuzzy">
<gallery mode="packed" heights="150px">
<gallery mode="packed" heights="150px">
Image: 4_latches.png | Step 1
Image: 4_latches.png | Latches
Image: Case2.jpg | Step 2
Image: Case2.jpg | Removing the back cover
Image: Case4.jpg | Step 3
Image: Case4.jpg | Back cover removed
Image: Case5.jpg | Step 4
Image: Case5.jpg | Removing the circuit board
</gallery>
</gallery>
</div>


=== Assembly ===
=== Assembly ===
Assembly is carried out in the reverse order.
Assembly is carried out in the reverse order:


<div class="mw-translate-fuzzy">
#Place the controller board in the case.
'''Step 1'''. Place the controller board in the case.
#Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
</div>
#Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case.
#Install the back cover. The cover latches should close whith a clicking sound.


<div class="mw-translate-fuzzy">
<gallery mode="packed" heights="150px">
<gallery mode="packed" heights="150px">
Image: Case6.jpg | Step 1
Image: Case6.jpg | Circuit board installation
Image: Case7.jpg | Step 2
Image: Case7.jpg | Front panel switch
Image: Case5.jpg | Step 3
Image: Case5.jpg | Installing the connector in the aperture
Image: Case8.jpg | Step 4
Image: Case8.jpg | Cover installed
</gallery>
</gallery>
</div>


===Cover removing===
===Cover removing and installing===
It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid.
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case.
 
Removing:
#Place the controller face up.
#Pry the latches on a front cover open with the slotted screwdriver.
#Take off the cover.


<div class="mw-translate-fuzzy">
Installing:
'''Step 1'''. Lay the controller face up.
# Place the controller face up.
</div>
# Insert the power switch of the controller into the hole on the cover.
# Close all latches carefully.


<div class="mw-translate-fuzzy">
<gallery mode="packed" heights="160px">
<gallery mode="packed" heights="160px">
Image: Cover_rem1.jpg | Step 1
Image: Cover_rem1.jpg | Front cover
Image: Cover_rem2.jpg | Step 2
Image: Cover_rem2.jpg | Latches
Image: Cover_rem3.jpg | Step 3
Image: Cover_rem3.jpg | Front cover removed
</gallery>
</gallery>
</div>

Текущая версия на 09:05, 19 августа 2022

Другие языки:

Tools

To disassemble the controller, you will need a slotted screwdriver.

Disassembling

To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case:

  1. Place the controller back cover up.
  2. Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches.
  3. Use a screwdriver to bend back the remaining latches and take off the cover.
  4. Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB.

  • Latches

  • Removing the back cover

  • Back cover removed

  • Removing the circuit board

Assembly

Assembly is carried out in the reverse order:

  1. Place the controller board in the case.
  2. Make sure the On/Off switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
  3. Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case.
  4. Install the back cover. The cover latches should close whith a clicking sound.

  • Circuit board installation

  • Front panel switch

  • Installing the connector in the aperture

  • Cover installed

Cover removing and installing

It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case.

Removing:

  1. Place the controller face up.
  2. Pry the latches on a front cover open with the slotted screwdriver.
  3. Take off the cover.

Installing:

  1. Place the controller face up.
  2. Insert the power switch of the controller into the hole on the cover.
  3. Close all latches carefully.

  • Front cover

  • Latches

  • Front cover removed

Источник — https://wirenboard.com/wiki/index.php?title=Disassembling_the_controller_case/en&oldid=66682