Disassembling the controller case/en: различия между версиями
Matveevrj (обсуждение | вклад) |
(Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.») |
||
| (не показана 31 промежуточная версия 3 участников) | |||
| Строка 1: | Строка 1: | ||
<languages/> | <languages/> | ||
===Tools=== | ===Tools=== | ||
To disassemble the controller, you will need a slotted screwdriver. | To disassemble the controller, you will need a slotted screwdriver. | ||
===Disassembling=== | ===Disassembling=== | ||
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case | To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case: | ||
# | # Place the controller back cover up. | ||
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with | # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | ||
# Use a screwdriver to bend the remaining latches and | # Use a screwdriver to bend back the remaining latches and take off the cover. | ||
# | # Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB. | ||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
| Строка 23: | Строка 19: | ||
=== Assembly === | === Assembly === | ||
Assembly is carried out in the reverse order | Assembly is carried out in the reverse order: | ||
#Place the controller board in the case. | #Place the controller board in the case. | ||
#Make sure the '''On/Off''' switch on the front panel is in its | #Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch. | ||
#Slightly bend the side wall of the | #Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case. | ||
#Install the back cover. | #Install the back cover. The cover latches should close whith a clicking sound. | ||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
Image: Case6.jpg | | Image: Case6.jpg | Circuit board installation | ||
Image: Case7.jpg | | Image: Case7.jpg | Front panel switch | ||
Image: Case5.jpg | | Image: Case5.jpg | Installing the connector in the aperture | ||
Image: Case8.jpg | | Image: Case8.jpg | Cover installed | ||
</gallery> | </gallery> | ||
===Cover removing=== | ===Cover removing and installing=== | ||
It is required to remove the controller cover to install the SIM card into the GSM module. The | It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case. | ||
Removing: | |||
#Place the controller face up. | |||
#Pry the latches on a front cover open with the slotted screwdriver. | |||
#Take off the cover. | |||
Installing: | |||
# Place the controller face up. | |||
# Insert the power switch of the controller into the hole on the cover. | |||
# Close all latches carefully. | |||
<gallery mode="packed" heights="160px"> | <gallery mode="packed" heights="160px"> | ||
Image: Cover_rem1.jpg | | Image: Cover_rem1.jpg | Front cover | ||
Image: Cover_rem2.jpg | | Image: Cover_rem2.jpg | Latches | ||
Image: Cover_rem3.jpg | | Image: Cover_rem3.jpg | Front cover removed | ||
</gallery> | </gallery> | ||
Текущая версия на 09:05, 19 августа 2022
Tools
To disassemble the controller, you will need a slotted screwdriver.
Disassembling
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case:
- Place the controller back cover up.
- Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches.
- Use a screwdriver to bend back the remaining latches and take off the cover.
- Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB.
Latches
Removing the back cover
Back cover removed
Removing the circuit board
Assembly
Assembly is carried out in the reverse order:
- Place the controller board in the case.
- Make sure the On/Off switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
- Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case.
- Install the back cover. The cover latches should close whith a clicking sound.
Circuit board installation
Front panel switch
Installing the connector in the aperture
Cover installed
Cover removing and installing
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case.
Removing:
- Place the controller face up.
- Pry the latches on a front cover open with the slotted screwdriver.
- Take off the cover.
Installing:
- Place the controller face up.
- Insert the power switch of the controller into the hole on the cover.
- Close all latches carefully.
Front cover
Latches
Front cover removed
