Disassembling the controller case/en: различия между версиями

Текущая версия на 09:05, 19 августа 2022

Другие языки:

English
русский

Tools

To disassemble the controller, you will need a slotted screwdriver.

Disassembling

To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case:

Place the controller back cover up.
Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches.
Use a screwdriver to bend back the remaining latches and take off the cover.
Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB.

Latches
Removing the back cover
Back cover removed
Removing the circuit board

Assembly

Assembly is carried out in the reverse order:

Place the controller board in the case.
Make sure the On/Off switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case.
Install the back cover. The cover latches should close whith a clicking sound.

Circuit board installation
Front panel switch
Installing the connector in the aperture
Cover installed

Cover removing and installing

It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case.

Removing:

Place the controller face up.
Pry the latches on a front cover open with the slotted screwdriver.
Take off the cover.

Installing:

Place the controller face up.
Insert the power switch of the controller into the hole on the cover.
Close all latches carefully.

Front cover
Latches
Front cover removed

@@ Строка 1: / Строка 1: @@
 <languages/>
-{{DISPLAYTITLE: Disassembling the controller case }}
 ===Tools===
-To disassemble a controller, you will need a slotted screwdriver.
+To disassemble the controller, you will need a slotted screwdriver.
 ===Disassembling===
-To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of the controller from the case:
+To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case:
-# Put the controller back cover up.
+# Place the controller back cover up.
 # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches.
 # Use a screwdriver to bend back the remaining latches and take off the cover.
-# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector.
+# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB.
 <gallery mode="packed" heights="150px">
@@ Строка 21: / Строка 19: @@
 === Assembly ===
-Assembly is carried out in the reverse order.
+Assembly is carried out in the reverse order:
 #Place the controller board in the case.
 #Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
-#Slightly bend back the side wall of the case where a connector for linking external modules is located. Gently press the board into the case so that the connector fits into the opening in the side of the case.
+#Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case.
-#Install the back cover. Lid latches should click into place.
+#Install the back cover. The cover latches should close whith a clicking sound.
 <gallery mode="packed" heights="150px">
@@ Строка 35: / Строка 33: @@
 </gallery>
-===Cover removing===
+===Cover removing and installing===
-It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid.
+It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case.
+Removing:
+#Place the controller face up.
+#Pry the latches on a front cover open with the slotted screwdriver.
+#Take off the cover.
-#Lay the controller face up.
+Installing:
-#Pry the latches on the controller cover with a flat screwdriver.
+# Place the controller face up.
-#Remove the cover.
+# Insert the power switch of the controller into the hole on the cover.
+# Close all latches carefully.
 <gallery mode="packed" heights="160px">

Навигация