Перейти к содержанию

Навигация

Firmware Changelog: различия между версиями

(не показаны 23 промежуточные версии 4 участников)
Строка 12: Строка 12:
!Affected devices
!Affected devices
!Changelog
!Changelog
|-
|-
|wb-ref-carel
|WB-MCM
| 2022-01-28
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MCM/main/1.3.1/ 1.3.1]
| WB-MCM8
|
* fix power down counters save [[WB-MCM8:_Errata#ERRMCM01: Не сохраняются счетчики при потере питания|ERRMCM01]]
* fix V_MCU T_MCU [[WB-MCM8:_Errata#ERRMCM02: Неверные значения температуры и напряжения питания микроконтроллера|ERRMCM02]]
 
|-
|WB-MRGBW-D
| 2022-01-28
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MRGB/main/3.0.0/ 3.0.0]
| WB-MRGBW-D
|
* added:    New button controls mechanism. Short, long, double, shortlong event handlers
* added:    Use flash_storage for settings saving
* rework:  Use wb_rcc
* added:    11 dimmer modes
* added:    CTT support
* added:    RGB <-> HSV conversion
* added:    Hue changing function
* added:    Counters for each click types (short, long, etc)
* added:    320-323 holdregs stores version as digits: major, minor, patch, suffix
* added:    324-325 holdregs stores version as uint32 in little-endian format
* added:    326-327 holdregs stores version as uint32 in big-endian format
 
|-
|WB-MS
| 2022-01-28
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/main/4.18.0/ 4.18.0]
| WB-MSWv3, WB-MIR
|
* added:    Holdreg 5500 - play IR command from ROM
* added:    Holdreg 5501 - edit IR command (ROM -> RAM)
* added:    Holdreg 5502 - learn IR command to ROM
* fixed:    Reset all ROMs command (coil 5000) reset only first ROM
* fixed:    ROM Size is not updated if ROM was cleared by editing command
* fixed:    Error is returned when coil disabled after editing ROM if first two regs are zeroes
 
|-
|WB-MS
| 2022-01-27
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/main/4.17.7/ 4.17.7]
| WB-MSWv3
| make target MSW3_4_9_GD32_TH
 
|-
|WB-MS
| 2022-01-26
|4.17.6
not released
| all
| improve adc driver. fix random bursts in adc channels like PIR or SPL.
 
|-
|WB-MS
| 2022-01-26
|4.17.5
not released
| WB-MAI2-mini
| added registers (holdreg 273,274) for setting the low-pass filter for inputs and saving setting to EEPROM
 
|-
|WB-MS
| 2022-01-19
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.17.4/ 4.17.4]
| WB-MSWv3
| increase in the measurement speed due to the fact that the illumination value is written
to the register at each measurement of the light sensor WB-MSW v.3 hw. 4.19.
 
|-
|WB-MS
| 2022-01-14
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.17.3/ 4.17.3]
| WB-MSWv3
| added support calibration of the light sensor WB-MSW v3 hw. 4.19 (holdreg 288)
 
|-
|WB-MR
| 2021-12-13
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MR/stable/1.16.4/ 1.16.4]
| WB-MR
| added support MRWM2 voltage and power measure relay module
 
|-
|WB-MS
| 2021-12-14
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.17.2/ 4.17.2]
| WB-MSWv3
| increase in measurement speed for light sensor WB-MSW v3 hw. 4.19
 
|-
|WB-MS
| 2021-12-03
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.17.1/ 4.17.1]
| WB-MSWv3
| new lid transmittance constant for WB-MSW v.3 hw. 4.19
 
|-
|WB-MS
| 2021-11-22
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.17.0/ 4.17.0]
| WB-MSWv3
|support for WB-MSW v.3 hw. 4.19
 
|-
|WB-MAP
|2020-12-07
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MAP/stable/2.3.3/ 2.3.3]
| WB-MAP3E
| add target MAP3E GD32
 
|-
|WB-REF-CR
|2021-11-13
|2021-11-13
|1.0.1
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-REF-CR/stable/1.0.1/ 1.0.1]
|[[WB-REF-U-CR_Carel_PYEZ/PJEZ_Modbus_Module | WB-REF-U-CR]]
|[[WB-REF-U-CR_Carel_PYEZ/PJEZ_Modbus_Module | WB-REF-U-CR]]
| Fix modbus device signature
| Fix modbus device signature