История
20 апреля 2021
19 июля 2019
Новая страница: «1: PWM 10V ||Output mode | |- | 120 (0x78) || holding || RW|| 0 || 0 || write to the register causes a stateless reboot of the module |not supported |- | 121 (0x…»
−215
Новая страница: «| 0 ||holding||RW||-||0-255||Channel level G, logarithmic curve | |- |1||holding||RW||-||0-255||the Level of the R channel, the logarithmic curve | |- |2 |holding…»
−255
Новая страница: «{| border="1" class="wikitable" style="text-align:center" !Register / address !type !read-write !default !format !Purpose !Note |-»
−95
Новая страница: «In any operating mode, the current status of the buttons can be read from HOLDING_REGISTER at 6 and 7. 0 - button unpressed, 1 - pressed. ==== Register map ====»
−80
Новая страница: «You can disable channel management using the buttons by writing 255(0xFF) to HOLDING_REGISTER at address 5.»
−69
Новая страница: «Button 2. Long press the button – smooth color change.»
−58
Новая страница: «Button 1. Short press – turns all channels on/off. Long press – smoothly change the brightness of all channels.»
−115
Новая страница: «The module has inputs for three hardware buttons.»
−36
Нет описания правки
−40
Новая страница: «<!--''<u>Страница находится в разработке!d</u>''-->»
+7
Нет описания правки
−18
Новая страница: «The module uses pulse width modulation (PWM), bit depth: 12 bit, PWM frequency: 24 kHz. ==== Buttons ====»
−83
Новая страница: «The brightness of the channel is set by an 8-bit number (0-255). The physical brightness of the LEDs is set according to the logarithmic dimming curve.»
−134
Новая страница: «==== LED control ====»
−34
Новая страница: «6 bytes '''signature''' lies at the address 200. The signature is unique for each device model and allows you to identify the model. To obtain the signatures nece…»
−229
Новая страница: «'''Address change''' is broadcast (slave_id 0) team record (WRITE_SINGLE_REGISTER) to holding register with address 128 (0x80).»
−79
Новая страница: «=== Functions===»
−5
Новая страница: «Speed is 9600 bit/s, data - 8 bit, parity – no, stop bit - 2. ==== Commands supported by device ==== {| border="1" cellpadding="3" cellspacing="0" !Command !com…»
−94
Новая страница: «== Management== ==== Bus parameters ====»
−24
Новая страница: «* b2 and GND - brightness control button»
−24
Новая страница: «* b1 and GND - color balance control button»
−30
Новая страница: «* GND - ground RS-485 bus (if any)»
−19
Новая страница: «* A and B - RS485 signal lines»
−20
Новая страница: «RS-485 and control buttons are connected to the blue terminals:»
−37
Новая страница: «The module is made in the unselfish version - the board is in a shrink tube.»
−57
Новая страница: «==== Connection ====»
−27
Новая страница: «* Air temperature from -40°C to +70°C; * Relative humidity up to 95%, without moisture condensation.»
−76
Новая страница: «====Operating conditions====»
−22
Новая страница: «* 4 channels 0-10V or 10V PWM * PWM frequency up to 400 Hz. * Supply voltage: 11 to 24 V. * Power consumption: 0.3 W. * Interface: RS485, Modus RTU * RS-485 inter…»
−340
Новая страница: «==Technical specifications==»
−33
Новая страница: «The module is controlled from the controller or PC via the RS-485 bus by MODBUS commands, as well as by external buttons.»
−110
Новая страница: «The type of output signal: 0-10V or PWM c with an amplitude of 10V. Type of output signals is configured (for all channels at once).»
−72
Новая страница: «4-channel lighting control module is designed to control lamps with interfaces 0-10V, PWM, as well as to control arbitrary load with the corresponding inputs.»
−182
Нет описания правки
−14
Новая страница: «500px|thumb|right| Диммер WB-MAO4''<u>The page is in development!</u>''»
+7176