WB-MR3xV and WB-MR6xV Modbus Relay Modules/en: различия между версиями

{/class= " wikitable"

!Modification I

!Modification S

!Modification R

|Maximum switching current,

230V AC resistive load

| colspan= "3" |16A

|Maximum switching current,

resistive load 30V DC

|Maximum switching power

for incandescent lamps (230V AC)

|"'3000W"'

|Maximum permissible starting current

(within 20ms, for contact NO.)

|"'165A"'

|Maximum permissible starting current

(within 200 microseconds, for contact NO)

|"'800A"'

|Contact resistance

| colspan= "3" / 100 milliohms

|Contact material

|"'W+AgSnO₂"'

| Contact configuration

|"'SPDT (NO, COM, NC)"'

|SPST (NO / COM)

|"'SPDT (NO, COM, NC)"'

|Lifetime: number of switches

for load 16A 230V AC, cos φ = 1

|Lifetime: number of switches

|20 000 000

| Relay model

|Peculiar properties

|Large inrush current,  

|Very large inrush current

|Low price

|Application

| colspan= " 2 " |General purpose Power load, inductive load,  

capacitive load. Motors, contactors, incandescent lamps,  

led lights, switching power supplies, etc.

|Resistive load, contactors,

of the low intensity.

=== Outputs ===

The inputs of the WB-MR3xV and WB-MR6xV modules are connected to screw terminals. Depending on the model, the modules have discrete inputs of different types.  

In LV modification inputs are organized on the principle of "dry contact". Buttons or switches are connected between the corresponding input of the Inputs unit and the GND.

In the HV modification, the inputs determine the presence of a connected phase of the 220 V AC network. Input voltage: 90V — 250V AC. External buttons and switches are connected between the corresponding input of the Inputs unit and the phase. The 230V neutral (N) is connected to the terminal "N" of the module.

==Technical specifications==

{| border="1" class= "wikitable" style= " text-align:left"

!Parameter

!Value

! colspan= " 2 " / Power

|Supply voltage

|9-24V DC

|Power consumption

* Idle mode (with all relays off) — 0.5 W

*With all relays on-WB-MR3xV: 1.5 W; WB-MR6xV: 3W

* Peak value-up to 8W for 20ms

! colspan= " 2 " | "'Outputs"'

|Output type

| Mechanical relay contacts

| Output configuration

|3 or 6 outputs connected to relay contacts

| Configuration of contacts of each output

|Two-position, normally open in modification "'S"' (C and NO)

Two-position with switching in modifications "'I"' and "'R"' (NC C NO)

|Maximum switching voltage, AC

|250 V

|Maximum switching voltage, DC

|30 V

|Maximum switching current per channel

see the table in [[Special: MyLanguage/#relay Parameters| # relay Parameters]]

|Contact resistance

|< 100 milliohms

|Voltage isolation between the controller and the output

| 1500 V (RMS)

|Term life:  

|see table under [[Special:MyLanguage/ # relay Parameters| # relay Parameters]]

! colspan= " 2 " / Inputs

|Number of inputs (Inputs 1&mdash; 4)

|4 (3+1) for WB-MR3xV

7 (6+1) for WB-MR6xV

| Input type (WB-MR3LV and WB-MR6LV)

| "Dry contact", group isolation.  

The input voltage is ~4.5 V.  

Input short-circuit current ~2mA.

| Input type (WB-MR3HV and WB-MR6HV)

| "Network availability", group isolation.  

Input voltage: 90V — 250VAC/DC. The current is ~0.5 mA.

|Functions

* General purpose inputs

* Signal count

* Direct control of relay channels

* Simultaneous shutdown of the entire load

*Remember the relay status in case of power cuts

! colspan= " 2 " / Control

|Management interface

| Interface isolation

|Uninsulated

|Communication protocol

| Modbus RTU, address is programmed, factory settings are indicated on the sticker

| RS-485 interface parameters

|set programmatically via Modbus registers; < br> default: speed-9600 bps; data-8 bits; parity — none (N); stop-bits-2

| Ready for operation after power supply

| ~0.03 c

! colspan= " 2 " / dimensions

|Width, DIN units

| Overall dimensions (L x W x H)  

|WB-MR3xV: 53.3 x 90.2 x 57.5 mm

WB-MR6xV: 106.25 x 90.2 x 57.5 mm

! colspan="2" |Indication

| Power and data exchange indication

| Yellow status led

| Relay channel status indication

|Green LEDs, WB-MR3xV: 1-3, WB-MR6xV: 1-6

! colspan= " 2 | / operating Conditions

|Air temperature

|-40 to +50 °C

|Relative humidity

|Up to 92%, non-condensing moisture

=== Overall dimensions ===

| [[File:DIN 6U.png |300px|thumb|center| WB-MR6xV overall dimensions: 106,25 x 90,2 x 57,5 mm (L x W х H)]]

| [[File:DIN 3U.png |400px|thumb|center|WB-MR3xV overall dimensions: 53,3 x 90,2 x 57,5 mm (L x W х H)]]

== Installation of WB-MR3xV and WB-MR6xV modules ==

The relay module is mounted on a standard 35 mm wide DIN rail and occupies a width of 3/6 DIN modules.

The screwless terminal blocks on the relay Board are used to connect power lines, control (RS-485) and input contacts. When used with the mounting lugs of the type NSVI to install wires into screwless terminals it is necessary that the diameter of the insulated cuff does not exceed 3.6 mm, wire size — 0.75 mm², and the length of the conductive sleeve — 5-6 mm. Screw terminals accept wire cross-section 2,5—4 mm². The cross section of the wire must correspond to the switched load.  

It is important not to exceed the recommended current of 16 A, when connecting switched devices to the KX relay contacts.  

The current flowing when a button or switch is shorted is small, so the type of button or switch can be anything. Despite the built-in anti-rattle protection, choose quality buttons and switches to avoid false positives due to bad contacts. Caution-in the HV modification, high voltage is present at the terminals!

If the device is the last on the RS-485 line, a 120 Ohm terminator resistor must be installed between its inputs A and B. Practice shows that in the case of bench tests with a small length of the RS-485 line and a small number of devices, the terminator on the last device in the line can not be installed.  

The module must be installed in such a way as to meet electrical safety requirements and prevent accidental contact of contacts under high voltage. The module must be operated under recommended environmental conditions.

[[File:Installation_WB3_+_WB5_+_DIN.png|850px|thumb|center|The Installation and connection sample of module WB-MR3HV/I. Choice of quality power supply is very important for the operation of the module. A button with yellow wires connected to input "4" of the module disables all three channels simultaneously]]

[[File:Installation_WB_MR6LV+WB5.png|850px|thumb|center|The installation and connection sample of module WB-MR6HV/I.Choice of quality power supply is very important for the operation of the module. A button with yellow wires connected to input "7" of the module disables all three channels simultaneously]]

== Relay operation mode in case of power failure ==

Depending on the value written to the storage register 0x06, after the power is turned off and restored, the relays will remain off (if the value is 0, or turn on those that were turned on before the power interruption if the register has a value of 1). This feature appeared in the modules with the firmware, starting with version 1.5.3.

==Modbus Control==

Details of the work with the module via Modbus Protocol is written in [[Relay Module Modbus Management/en| Relay Modules Modbus Management ]].

You can also find a map of the device registers there.

[[Периферийные устройства с интерфейсом RS-485 серии WB-xxxx/en |Back to peripheral devices list]]