WB-REF-U-CR Modbus Registers: различия между версиями

Материал из Wiren Board
Строка 1694: Строка 1694:
|-
|-
|}
|}
== uRack ==
{{Wbincludes:Carel Modbus Register Table Header}}
| 0x0195
| style="text-align:right;" | 405
| input
| u16
| LP1
| Probe B4
| bar
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x0199
| style="text-align:right;" | 409
| input
| u16
| HP/LP2
| Probe B1
| bar/°C
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x0196
| style="text-align:right;" | 406
| input
| u16
| B2
| Probe B2
| °C/°F
| style="text-align:right;" | -40
| style="text-align:right;" | 150
|-
| 0x0193
| style="text-align:right;" | 403
| input
| u16
| B3
| Probe B3
| °C/°F
| style="text-align:right;" | -40
| style="text-align:right;" | 150
|-
| 0x019C
| style="text-align:right;" | 412
| holding
| u16
| r01
| Suction set point circuit 1
| bar
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x019A
| style="text-align:right;" | 410
| holding
| u16
| r02
| Differential circuit 1
| bar
| style="text-align:right;" | 0
| style="text-align:right;" | 20
|-
| 0x019E
| style="text-align:right;" | 414
| holding
| u16
| r03
| Suction set point circuit 2
| bar
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x019F
| style="text-align:right;" | 415
| holding
| u16
| r04
| Differential circuit 2
| bar
| style="text-align:right;" | 0
| style="text-align:right;" | 20
|-
| 0x0197
| style="text-align:right;" | 407
| holding
| u16
| r12
| Min suction set point 1
| bar
| style="text-align:right;" | 0
| style="text-align:right;" |
|-
| 0x019B
| style="text-align:right;" | 411
| holding
| u16
| r13
| Max suction set point 1
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x019D
| style="text-align:right;" | 413
| holding
| u16
| r14
| Min suction set point 2
| bar
| style="text-align:right;" | 0
| style="text-align:right;" |
|-
| 0x0190
| style="text-align:right;" | 400
| holding
| u16
| r15
| Max suction set point 2
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x0198
| style="text-align:right;" | 408
| holding
| u16
| r16(bar)
| Fan set point (bar)
| bar
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x0192
| style="text-align:right;" | 402
| holding
| u16
| r16 (°C)
| Fan set point (°C)
| °C/°F
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x0191
| style="text-align:right;" | 401
| holding
| u16
| r17 (bar)
| Fan differential (bar)
| bar
| style="text-align:right;" | 0
| style="text-align:right;" | 20
|-
| 0x0194
| style="text-align:right;" | 404
| holding
| u16
| r17(°C)
| Fan differential (°C)
| °C/°F
| style="text-align:right;" | 0
| style="text-align:right;" | 20
|-
| 0x01A5
| style="text-align:right;" | 421
| holding
| u16
| r25(bar)
| Min fan set point (bar)
| °F
| style="text-align:right;" | 0
| style="text-align:right;" |
|-
| 0x01A9
| style="text-align:right;" | 425
| holding
| u16
| r25 (°C)
| Min fan set point (°C)
| °C/°F
| style="text-align:right;" | 0
| style="text-align:right;" |
|-
| 0x01A6
| style="text-align:right;" | 422
| holding
| u16
| r26(bar)
| Max fan set point (bar)
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x01A3
| style="text-align:right;" | 419
| holding
| u16
| r26(°C)
| Max fan set point (°C)
| °C/°F
| style="text-align:right;" |
| style="text-align:right;" | 150
|-
| 0x01AC
| style="text-align:right;" | 428
| holding
| u16
| r18 (bar)
| Fan inverter set point (bar)
| bar
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x01AA
| style="text-align:right;" | 426
| holding
| u16
| r18 (°C)
| Fan inverter set point (°C)
| °C/°F
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x01AE
| style="text-align:right;" | 430
| holding
| u16
| r19 (bar)
| Fan inverter differential
| bar
| style="text-align:right;" | 0
| style="text-align:right;" | 20
|-
| 0x01AF
| style="text-align:right;" | 431
| holding
| u16
| r19 (°C)
| Fan inverter differential
| °C/°F
| style="text-align:right;" | 0
| style="text-align:right;" | 20
|-
| 0x01A7
| style="text-align:right;" | 423
| holding
| u16
| A01
| HP suction 1 alarm threshold
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x01AB
| style="text-align:right;" | 427
| holding
| u16
| A03
| LP suction 1 alarm threshold
| bar
| style="text-align:right;" | -0.5
| style="text-align:right;" | 7
|-
| 0x01AD
| style="text-align:right;" | 429
| holding
| u16
| A05
| HP suction 2 alarm threshold
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x01A0
| style="text-align:right;" | 416
| holding
| u16
| A07
| LP suction 2 alarm threshold
| bar
| style="text-align:right;" | -0.5
| style="text-align:right;" | 7
|-
| 0x01A8
| style="text-align:right;" | 424
| holding
| u16
| A09 (bar)
| HP discharge alarm threshold (bar)
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x01A2
| style="text-align:right;" | 418
| holding
| u16
| A09 (°C)
| HP discharge alarm threshold (°C)
| °C/°F
| style="text-align:right;" |
| style="text-align:right;" | 150
|-
| 0x01A1
| style="text-align:right;" | 417
| holding
| u16
| A10(bar)
| LP discharge alarm threshold (bar)
| bar
| style="text-align:right;" | 0
| style="text-align:right;" |
|-
| 0x01A4
| style="text-align:right;" | 420
| holding
| u16
| A10 (°C)
| LP discharge alarm threshold (°C)
| °C/°F
| style="text-align:right;" | 0
| style="text-align:right;" |
|-
| 0x01B5
| style="text-align:right;" | 437
| holding
| u16
| /23
| Suction probe 4 calibration
| bar
| style="text-align:right;" | -12
| style="text-align:right;" | 12
|-
| 0x01B9
| style="text-align:right;" | 441
| holding
| u16
| /24
| Discharge probe 1 calibration
| bar
| style="text-align:right;" | -12
| style="text-align:right;" | 12
|-
| 0x01B6
| style="text-align:right;" | 438
| holding
| u16
| /25
| Room probe 2 calibration
| °C/°F
| style="text-align:right;" | -12
| style="text-align:right;" | 12
|-
| 0x01B3
| style="text-align:right;" | 435
| holding
| u16
| /26
| Outside probe 3 calibration
| °C/°F
| style="text-align:right;" | -12
| style="text-align:right;" | 12
|-
| 0x01BC
| style="text-align:right;" | 444
| holding
| u16
| /17
| Min value suction transducer
| bar
| style="text-align:right;" | -1
| style="text-align:right;" |
|-
| 0x01BA
| style="text-align:right;" | 442
| holding
| u16
| /18
| Min value discharge transducer
| bar
| style="text-align:right;" | -1
| style="text-align:right;" |
|-
| 0x01BE
| style="text-align:right;" | 446
| holding
| u16
| /19
| End scale value suction transducer
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x01BF
| style="text-align:right;" | 447
| holding
| u16
| /20
| End scale value discharge transducer
| bar
| style="text-align:right;" |
| style="text-align:right;" | 40
|-
| 0x01B7
| style="text-align:right;" | 439
| holding
| u16
| /33
| Set point prevent high pressure function
| bar
| style="text-align:right;" | 0
| style="text-align:right;" | 40
|-
| 0x01BB
| style="text-align:right;" | 443
| holding
| u16
| r34
| Set point offset to change set from DI
| bar
| style="text-align:right;" | -99
| style="text-align:right;" | 99
|-
| 0x01BD
| style="text-align:right;" | 445
| holding
| u16
| r11
| Differential pressure for dead band by time
| bar
| style="text-align:right;" | 0
| style="text-align:right;" | 20
|-
| 0x01B0
| style="text-align:right;" | 432
| holding
| u16
| r33
| Condensing temperature delta for floating control
| °C/°F
| style="text-align:right;" | -40
| style="text-align:right;" | 150
|-
| 0x01B8
| style="text-align:right;" | 440
| holding
| u16
| A16
| High temp threshold probe B2
| °C/°F
| style="text-align:right;" | -40
| style="text-align:right;" | 150
|-
| 0x01B2
| style="text-align:right;" | 434
| holding
| u16
| A17
| High temp threshold probe B3
| °C/°F
| style="text-align:right;" | -40
| style="text-align:right;" | 150
   
|-
| 0x01B1
| style="text-align:right;" | 433
| holding
| u16
| /00
| Type of unit
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01B4
| style="text-align:right;" | 436
| holding
| u16
| /01
| Unit model
|
| style="text-align:right;" | 0
| style="text-align:right;" | 14
|-
| 0x01C5
| style="text-align:right;" | 453
| input
| u16
| -
| Number of compressors
|
| style="text-align:right;" | 0
| style="text-align:right;" | 4
|-
| 0x01C9
| style="text-align:right;" | 457
| holding
| u16
| /09
| Number of fans
|
| style="text-align:right;" | 0
| style="text-align:right;" | 4
|-
| 0x01C6
| style="text-align:right;" | 454
| input
| u16
| -
| Unit status
|
| style="text-align:right;" | 0
| style="text-align:right;" | 7
|-
| 0x01C3
| style="text-align:right;" | 451
| holding
| u16
| r07
| Minimum call time for compressor start (dead band)
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01CC
| style="text-align:right;" | 460
| holding
| u16
| r09
| Minimum call time for compressor stop (dead band)
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01CA
| style="text-align:right;" | 458
| holding
| u16
| C01
| Minimum compressor ON time
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01CE
| style="text-align:right;" | 462
| holding
| u16
| C02
| Minimum compressor OFF time
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01CF
| style="text-align:right;" | 463
| holding
| u16
| C03
| Minimum time between starts of different compressors
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01C7
| style="text-align:right;" | 455
| holding
| u16
| C05
| Minimum time between starts of the same compressor
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01CB
| style="text-align:right;" | 459
| holding
| u16
| -
| Fan start delay (dead band)
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01CD
| style="text-align:right;" | 461
| holding
| u16
| -
| Fan stop delay (dead band)
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01C0
| style="text-align:right;" | 448
| holding
| u16
| A18
| Liquid level alarm delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01C8
| style="text-align:right;" | 456
| holding
| u16
| -
| Minimum fan speed
| %
| style="text-align:right;" | 0
| style="text-align:right;" | 100
|-
| 0x01C2
| style="text-align:right;" | 450
| holding
| u16
| /07
| Number of compressors on in circuit 1 with probe damaged
|
| style="text-align:right;" | 0
| style="text-align:right;" | 4
|-
| 0x01C1
| style="text-align:right;" | 449
| holding
| u16
| /08
| Number of compressors on in circuit 2 with probe damaged
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01C4
| style="text-align:right;" | 452
| holding
| u16
| /12
| Number of fans on with probe damaged
|
| style="text-align:right;" | 0
| style="text-align:right;" | 4
|-
| 0x01D5
| style="text-align:right;" | 469
| input
| u16
| -
| Version of the application
|
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x01D9
| style="text-align:right;" | 473
| holding
| u16
| /35
| Type of refrigerant
|
| style="text-align:right;" | 0
| style="text-align:right;" | 11
|-
| 0x01D6
| style="text-align:right;" | 470
| holding
| u16
| /03
| Capacity of compressor 1
|
| style="text-align:right;" | 0
| style="text-align:right;" | 500
|-
| 0x01D3
| style="text-align:right;" | 467
| holding
| u16
| /04
| Capacity of compressor 2
|
| style="text-align:right;" | 0
| style="text-align:right;" | 500
|-
| 0x01DC
| style="text-align:right;" | 476
| holding
| u16
| /05
| Capacity of compressor 3
|
| style="text-align:right;" | 0
| style="text-align:right;" | 500
|-
| 0x01DA
| style="text-align:right;" | 474
| holding
| u16
| /06
| Capacity of compressor 4
|
| style="text-align:right;" | 0
| style="text-align:right;" | 500
|-
| 0x01DE
| style="text-align:right;" | 478
| input
| u16
| /11
| Inverter readout %
| %
| style="text-align:right;" | 0
| style="text-align:right;" | 100
|-
| 0x01DF
| style="text-align:right;" | 479
| holding
| u16
| /15
| Multifunction DI configuration
|
| style="text-align:right;" | 0
| style="text-align:right;" | 12
|-
| 0x01D7
| style="text-align:right;" | 471
| holding
| u16
| /16
| Type of discharge probe
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01DB
| style="text-align:right;" | 475
| holding
| u16
| /21
| Type of probe B2
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01DD
| style="text-align:right;" | 477
| holding
| u16
| /22
| Type of probe B3
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01D0
| style="text-align:right;" | 464
| holding
| u16
| /37
| Delay restart after black out
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01D8
| style="text-align:right;" | 472
| holding
| u16
| C04
| Min time between two stop calls for different compressors
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01D2
| style="text-align:right;" | 466
| holding
| u16
| C06
| Time between compressor stop call with Prevent function
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01D1
| style="text-align:right;" | 465
| holding
| u16
| C07
| Operating hour threshold for maintenance
| h x10
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01D4
| style="text-align:right;" | 468
| input
| u16
| C08
| Compressor 1 hours
| h x10
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E5
| style="text-align:right;" | 485
| input
| u16
| C10
| Compressor 2 hours
| h x10
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E9
| style="text-align:right;" | 489
| input
| u16
| C12
| Compressor 3 hours
| h x10
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E6
| style="text-align:right;" | 486
| input
| u16
| C14
| Compressor 4 hours
| h x10
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E3
| style="text-align:right;" | 483
| holding
| u16
| r05
| Type of compressor rotation
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01EC
| style="text-align:right;" | 492
| holding
| u16
| r06
| Type of compressor control
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01EA
| style="text-align:right;" | 490
| holding
| u16
| r08
| Maximum call for compressor starts in dead band by time
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01EE
| style="text-align:right;" | 494
| holding
| u16
| r10
| Maximum call for compressor stops in dead band by time
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01EF
| style="text-align:right;" | 495
| holding
| u16
| r20
| Type of fan rotation
|
| style="text-align:right;" | 0
| style="text-align:right;" | 1
|-
| 0x01E7
| style="text-align:right;" | 487
| holding
| u16
| r21
| Type of fan control
|
| style="text-align:right;" | 0
| style="text-align:right;" | 2
|-
| 0x01EB
| style="text-align:right;" | 491
| holding
| u16
| r22
| Integral time for P+I fan control
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01ED
| style="text-align:right;" | 493
| holding
| u16
| r23
| Time between 2 fans starts in dead band
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E0
| style="text-align:right;" | 480
| holding
| u16
| r24
| Time between 2 fans stops in dead band
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E8
| style="text-align:right;" | 488
| holding
| u16
| r27
| Inverter speed up time
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E2
| style="text-align:right;" | 482
| holding
| u16
| r28
| Inverter ramp up time
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01E1
| style="text-align:right;" | 481
| holding
| u16
| r29
| Minimum inverter output
| %
| style="text-align:right;" | 0
| style="text-align:right;" | 100
|-
| 0x01E4
| style="text-align:right;" | 484
| holding
| u16
| r30
| Maximum inverter output
| %
| style="text-align:right;" | 0
| style="text-align:right;" | 100
|-
| 0x01F5
| style="text-align:right;" | 501
| holding
| u16
| r31
| Triac impulse duration
| ms
| style="text-align:right;" | 0
| style="text-align:right;" | 10
|-
| 0x01F9
| style="text-align:right;" | 505
| holding
| u16
| A02
| High suction pressure 1 alarm delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01F6
| style="text-align:right;" | 502
| holding
| u16
| A04
| Low suction pressure 1 alarm delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01F3
| style="text-align:right;" | 499
| holding
| u16
| A06
| High suction pressure 2 alarm delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01FC
| style="text-align:right;" | 508
| holding
| u16
| A08
| Low suction pressure 2 alarm delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01FA
| style="text-align:right;" | 506
| holding
| u16
| A11
| Low discharge pressure alarm delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01FE
| style="text-align:right;" | 510
| holding
| u16
| A12
| Compressor thermal overload alarm delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01FF
| style="text-align:right;" | 511
| holding
| u16
| A13
| Prevent time in which no compressor starts are enabled
| m
| style="text-align:right;" | 0
| style="text-align:right;" | 99
|-
| 0x01F7
| style="text-align:right;" | 503
| holding
| u16
| A14
| Prevent time in which the activation signals the alarm
| m
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01FB
| style="text-align:right;" | 507
| holding
| u16
| A15
| Time to reset prevent alarm
| m
| style="text-align:right;" | 0
| style="text-align:right;" | 99
|-
| 0x01FD
| style="text-align:right;" | 509
| holding
| u16
| A20
| Alarm signal delay
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01F0
| style="text-align:right;" | 496
| holding
| u16
| A21
| Time to change low pressure alarm from automatic to manual
| s
| style="text-align:right;" | 0
| style="text-align:right;" | 999
|-
| 0x01F1
| style="text-align:right;" | 497
| input
| u16
|
| Operating percentage of first capacity controlled compressor
|
| style="text-align:right;" |
| style="text-align:right;" |
|-
| 0x01F4
| style="text-align:right;" | 500
| input
| u16
|
| Operating percentage of second capacity controlled compressor
|
| style="text-align:right;" |
| style="text-align:right;" |
|-
|}
==Общие регистры==
==Общие регистры==
{{Wbincludes:Common Modbus Registers|addlines=true}}
{{Wbincludes:Common Modbus Registers|addlines=true}}

Версия 19:53, 21 июля 2022

Описание

Регистры сетевой карты WB-REF-U-CR зависят от используемого холодильного контроллера Carel и перечислены в таблицах ниже. Данные в таблицах сгруппированы по функциям.

Служебные регистры сетевой карты вы найдёте в разделе Общие регистры.

PJ BASIC

Адрес Тип Формат Имя Назначение Единицы
измерения		 Значения
в Hex в DEC Минимум Максимум
0x0004 4 discrete u16 s_pre1 1st probe alarm
0x0001 1 discrete u16 s_pre2 2nd probe alarm
0x0009 9 discrete u16 s_pre3 3rd probe alarm
0x000C 12 discrete u16 s_LO Low temperature alarm
0x0003 3 discrete u16 s_HI High temperature alarm
0x0006 6 discrete u16 s_IA External immediate alarm
0x000F 15 discrete u16 s_dA External delay alarm
0x000A 10 discrete u16 s_Ed1 Timeout defrost alarm
0x000E 14 discrete u16 s_cht High temperature condense
0x0002 2 discrete u16 s_CHT High temperature condense
0x0005 5 discrete u16 s_Etc Broken RTC alarm
0x0017 23 discrete u16 s_EE Machine parameters eeprom
0x0010 16 discrete u16 s_EF Functions parameters eepr
0x0019 25 discrete u16 s_PreDor Pre-opened door alarm 0 0
0x001C 28 discrete u16 s_Dor Opened door alarm 0 0
0x0195 405 input s16 s_pr1 Probe 1 reading °C/°F 0 0
0x0199 409 input s16 s_pr2 Probe 2 reading °C/°F 0 0
0x0196 406 input s16 s_pr3 Probe 3 reading °C/°F 0 0
0x0193 403 holdng s16 /C1 Probe 1 offset °C/°F -20 20
0x019C 412 holdng s16 /C2 Probe 2 offset °C/°F -20 20
0x019A 410 holdng s16 St Set point °C/°F
0x019E 414 holdng s16 rd Control differential °C/°F 0 19
0x019F 415 holdng s16 r1 Minimum set point allowe °C/°F -50
0x0197 407 holdng s16 r2 Maximum set point allowed °C/°F 90
0x019B 411 holdng s16 dt End defrost temperature °C/°F -50 90
0x019D 413 holdng s16 A0 Alarm and fan differentia °C/°F -20 20
0x0190 400 holdng s16 AL Absolute/Relative tempera °C/°F -50 90
0x0198 408 holdng s16 AH Absolute/Relative tempera °C/°F -50 90
0x0192 402 holdng s16 F1 Fan control set point °C/°F -50 90
0x0007 7 discrete u16 s_din1 Status of digital input 1 0 0
0x0000 0 discrete u16 s_r1 Compressor relay status 0 0
0x000D 13 discrete u16 s_r2 Defrost relay status 0 0
0x0008 8 discrete u16 s_r3 Fan relay status 0 0
0x000B 11 discrete u16 s_r4 Auxiliary relay status 0 0
0x001D 29 discrete u16 s_DEF Defrost status 0 0
0x0018 24 coil s16 s_cDEF Defrost command 0 1
0x001B 27 discrete u16 s_CC Continuous cycle status 0 0
0x0014 20 coil u16 s_cCC Continuous cycle command 0 1
0x0013 19 coil u16 F0 Fan management 0 1
0x0016 22 coil u16 F3 Fan in defrost 0 1
0x001F 31 coil u16 s_cONOFF ON/OFF command 0 1
0x01A6 422 holdng u16 c0 Comp. and fan start delay Минуты 0 99
0x01A3 419 holdng u16 c2 Minimum compressor off ti Минуты 0 99
0x01AC 428 holdng u16 d0 Defrost type 0 4
0x01AA 426 holdng u16 dI Interval between defrosts Часы 0 24
0x01AE 430 holdng u16 dP Maximum defrost duration Минуты 1 99
0x01AF 431 holdng u16 dd Dripping time after defro Минуты 0 15
0x01A7 423 holdng u16 Ad Low and high temperature Минуты 0 99
0x01AB 427 holdng u16 A4 Third input configuration 0 2
0x01AD 429 holdng u16 F2 Fan off with compressor o °C/°F 0 2
0x01A0 416 holdng u16 Fd Post dripping time Минуты 0 15
0x01A8 424 holdng u16 F4 Start delay when fan on Секунды 1 99
0x01A2 418 holdng u16 F5 Fan on time (with F2=2) Минуты 1 99
0x01A1 417 holdng u16 F6 Fan off time (with F2=2) Минуты 1 99
0x01A4 420 input s16 H0 Serial address 0 207

PJ EASY

Адрес Тип Формат Имя Назначение Единицы
измерения		 Значения
в Hex в DEC Минимум Максимум
0x0007 7 discrete u16 Dig.input Digital input status
0x0000 0 discrete u16 Rel. comp. Compressor relay status
0x000D 13 discrete u16 Rel. defr. Defrost relay status
0x0008 8 discrete u16 Rel. fan. Fan relay status
0x000B 11 discrete u16 Rel.AUX Activate AUX command
0x001D 29 discrete u16 Defrost Defrost status
0x0018 24 coil u16 Defrost Activate defrost command
0x001B 27 discrete u16 C.C. Continuous cycle status
0x0014 20 coil u16 C.C. Activation contin. cycle
0x0011 17 discrete u16 s_nRTC Set point started by RTC
0x0013 19 coil u16 /5 Select C/F
0x0016 22 coil u16 /6 Disable decimal point
0x001F 31 coil u16 d4 Defrost at power-on
0x001A 26 coil u16 d6 Display lock during defr.
0x001E 30 coil u16 d9 Def prior over comp prots
0x0012 18 coil u16 dC Time base
0x0015 21 coil u16 A8 En alarm Ed
0x0027 39 coil u16 F0 Enable evap fan control
0x0020 32 coil u16 F2 Stop fans if compr stops
0x002D 45 coil u16 F3 Stop fans during defrost
0x0028 40 coil u16 H4 Buzzer inhibition
0x002B 43 coil u16 tEn Enable RTC
0x0024 36 coil u16 ON/OFF Controller ON/OFF command
0x0195 405 input u16 d/ Defrost probe value °C 0 0
0x0199 409 input u16 s_pr1 Probe 1 status °C 0 0
0x0196 406 input u16 s_pr2 Probe 2 status °C/°F 0 0
0x0193 403 input u16 s_pr3 Probe 3 status °C/°F 0 0
0x019C 412 holdng u16 /C1 Probe 1 offset °C 12
0x019A 410 holdng u16 /C2 Probe 2 offset °C/°F 12
0x019E 414 holdng u16 /C3 Probe 3 offset °C/°F 12
0x019F 415 holdng u16 St User set point °C
0x0197 407 holdng u16 rd Differential °C 0 19
0x019B 411 holdng u16 r1 Minimum set point allowed °C/°F -50 pk78
0x019D 413 holdng u16 r2 Maximum set point allowed °C/°F pk79 150
0x0190 400 holdng u16 r4 Night-time set point diff °C/°F -50 50
0x0198 408 holdng u16 dt End defrost temperature °C/°F -50 127
0x0192 402 holdng u16 A0 Al and fan differential °C/°F -20 20
0x0191 401 holdng u16 AL Low temperature alarm °C -50 150
0x0194 404 holdng u16 AH High temperature alarm °C -50 150
0x01A5 421 holdng u16 Ac Dirty cond Al set point °C/°F -50 150
0x01A9 425 holdng u16 AE Dirty cond Al temp. diff. °C/°F 0.1 20
0x01A6 422 holdng u16 F1 Evap fan control sp °C -50 127
0x01A3 419 holdng u16 tc_d RTC day of the week День 1 7
0x01AC 428 holdng u16 tc_h RTC hour Часы 0 23
0x01AA 426 holdng u16 tc_m RTC minutes Минуты 0 59
0x01AE 430 input u16 hw_RTC RTC presence 0 1
0x01AF 431 input u16 hw_model Machine model 0 255
0x01A7 423 input u16 hw_probe Probe type NTC/PTC 0 1
0x01AD 429 holdng u16 /2 Probe meas. stability 1 15
0x01A0 416 holdng u16 /4 Select display probe 1 3
0x01A8 424 holdng u16 r3 Direct/reverse 0 2
0x01A2 418 holdng u16 c0 Start delay after Pow-on Минуты 0 100
0x01A1 417 holdng u16 c1 Delay between starts Минуты 0 100
0x01A4 420 holdng u16 c2 Min compressor OFF time Минуты 0 100
0x01B5 437 holdng u16 c3 Min compressor ON time Минуты 0 100
0x01B9 441 holdng u16 c4 Duty setting time Минуты 0 100
0x01B6 438 holdng u16 cc Continuous cycle duration Часы 0 15
0x01B3 435 holdng u16 c6 Temp al bypass after c.c. Часы 0 15
0x01BC 444 holdng u16 d0 Type of defrost 0 4
0x01BA 442 holdng u16 dI Defrost interval Часы
0x01BE 446 holdng u16 dP Maximum defrost duration Минуты
0x01BF 447 holdng u16 d5 Def delay P-on, En Dig-In Минуты 0 199
0x01B7 439 holdng u16 dd Dripping time Минуты 0 15
0x01BB 443 holdng u16 d8 Alarm off after defrost Часы 0 15
0x01BD 445 holdng u16 Ad Temperature alarm delay Минуты
0x01B0 432 holdng u16 A4 3rd input conf. 0 11
0x01B8 440 holdng u16 A7 Digital input alarm delay Минуты 0 199
0x01B2 434 holdng u16 Acd Dirty cond. alarm delay Минуты 0 250
0x01B1 433 holdng u16 Fd Post-dripping timeout Минуты 0 15
0x01B4 436 input u16 H0 Serial address 0 207
0x01C5 453 holdng u16 H1 AUX output configuration 0 3
0x01C9 457 holdng u16 H2 Enable keypad 0 2
0x01C6 454 holdng u16 H5 ID code (read-only) 1 199
0x01C3 451 holdng u16 EZY Sel set of default param 0 4
0x01CC 460 holdng u16 d1d Defrost time band 1st day Дни 0 11
0x01CA 458 holdng u16 d1h Time band 1st hour Часы 0 23
0x01CE 462 holdng u16 d1m Time band 1st minutes Минуты 0 59
0x01CF 463 holdng u16 d2d Defrost time band 2nd day Дни 0 11
0x01C7 455 holdng u16 d2h Time band 2nd hour Часы 0 23
0x01CB 459 holdng u16 d2m Time band 2nd minutes Минуты 0 59
0x01CD 461 holdng u16 d3d Defrost time band 3rd day Дни 0 11
0x01C0 448 holdng u16 d3h Time band 3rd hour Часы 0 23
0x01C8 456 holdng u16 d3m Time band 3rd minutes Минуты 0 59
0x01C2 450 holdng u16 d4d Defrost time band 4th day Дни 0 11
0x01C1 449 holdng u16 d4h Time band 4th hour Часы 0 23
0x01C4 452 holdng u16 d4m Time band 4th minutes Минуты 0 59
0x01D5 469 holdng u16 nOd Night time band ON day Дни 0 11
0x01D9 473 holdng u16 nOh Night time band ON hour Часы 0 23
0x01D6 470 holdng u16 nOm Night time band ON min. Минуты 0 59
0x01D3 467 holdng u16 nFd Night time band OFF day Дни 0 11
0x01DC 476 holdng u16 nFh Night time band OFF hour Часы 0 23
0x01DA 474 holdng u16 nFm Night time band OFF min Минуты 0 59
0x01DE 478 holdng u16 AOd AUX time band ON day Дни 0 11
0x01DF 479 holdng u16 AOh AUX time band ON hour Часы 0 23
0x01D7 471 holdng u16 AOm AUX time band ON minutes Минуты 0 59
0x01DB 475 holdng u16 AFd AUX time band OFF day Дни 0 11
0x01DD 477 holdng u16 AFh AUX time band OFF hour Часы 0 23
0x01D0 464 holdng u16 AFm AUX time band OFF minutes Минуты 0 59
0x0004 4 discrete u16 s_pre1 1st probe alarm
0x0001 1 discrete u16 s_pre2 2nd probe alarm
0x0009 9 discrete u16 s_pre3 3rd probe alarm
0x000C 12 discrete u16 s_LO Low temperature alarm
0x0003 3 discrete u16 s_HI High temperature alarm
0x0006 6 discrete u16 s_IA External immediate alarm
0x000F 15 discrete u16 s_dA External delay alarm
0x000A 10 discrete u16 s_Ed1 Timeout defrost alarm
0x000E 14 discrete u16 s_cht High temp cond pre-alarm
0x0002 2 discrete u16 s_CHT High temp condenser alarm
0x0005 5 discrete u16 s_Etc Broken RTC alarm
0x0017 23 discrete u16 s_EE Machine param e2 alarm
0x0010 16 discrete u16 s_EF Func param eeprom alarm
0x0019 25 discrete u16 s_PreDor Open door pre-alarm state
0x001C 28 discrete u16 s_Dor Open door alarm state

uRack

Адрес Тип Формат Имя Назначение Единицы
измерения		 Значения
в Hex в DEC Минимум Максимум
0x0195 405 input u16 LP1 Probe B4 bar
0x0199 409 input u16 HP/LP2 Probe B1 bar/°C
0x0196 406 input u16 B2 Probe B2 °C/°F -40 150
0x0193 403 input u16 B3 Probe B3 °C/°F -40 150
0x019C 412 holding u16 r01 Suction set point circuit 1 bar
0x019A 410 holding u16 r02 Differential circuit 1 bar 0 20
0x019E 414 holding u16 r03 Suction set point circuit 2 bar
0x019F 415 holding u16 r04 Differential circuit 2 bar 0 20
0x0197 407 holding u16 r12 Min suction set point 1 bar 0
0x019B 411 holding u16 r13 Max suction set point 1 bar 40
0x019D 413 holding u16 r14 Min suction set point 2 bar 0
0x0190 400 holding u16 r15 Max suction set point 2 bar 40
0x0198 408 holding u16 r16(bar) Fan set point (bar) bar
0x0192 402 holding u16 r16 (°C) Fan set point (°C) °C/°F
0x0191 401 holding u16 r17 (bar) Fan differential (bar) bar 0 20
0x0194 404 holding u16 r17(°C) Fan differential (°C) °C/°F 0 20
0x01A5 421 holding u16 r25(bar) Min fan set point (bar) °F 0
0x01A9 425 holding u16 r25 (°C) Min fan set point (°C) °C/°F 0
0x01A6 422 holding u16 r26(bar) Max fan set point (bar) bar 40
0x01A3 419 holding u16 r26(°C) Max fan set point (°C) °C/°F 150
0x01AC 428 holding u16 r18 (bar) Fan inverter set point (bar) bar
0x01AA 426 holding u16 r18 (°C) Fan inverter set point (°C) °C/°F
0x01AE 430 holding u16 r19 (bar) Fan inverter differential bar 0 20
0x01AF 431 holding u16 r19 (°C) Fan inverter differential °C/°F 0 20
0x01A7 423 holding u16 A01 HP suction 1 alarm threshold bar 40
0x01AB 427 holding u16 A03 LP suction 1 alarm threshold bar -0.5 7
0x01AD 429 holding u16 A05 HP suction 2 alarm threshold bar 40
0x01A0 416 holding u16 A07 LP suction 2 alarm threshold bar -0.5 7
0x01A8 424 holding u16 A09 (bar) HP discharge alarm threshold (bar) bar 40
0x01A2 418 holding u16 A09 (°C) HP discharge alarm threshold (°C) °C/°F 150
0x01A1 417 holding u16 A10(bar) LP discharge alarm threshold (bar) bar 0
0x01A4 420 holding u16 A10 (°C) LP discharge alarm threshold (°C) °C/°F 0
0x01B5 437 holding u16 /23 Suction probe 4 calibration bar -12 12
0x01B9 441 holding u16 /24 Discharge probe 1 calibration bar -12 12
0x01B6 438 holding u16 /25 Room probe 2 calibration °C/°F -12 12
0x01B3 435 holding u16 /26 Outside probe 3 calibration °C/°F -12 12
0x01BC 444 holding u16 /17 Min value suction transducer bar -1
0x01BA 442 holding u16 /18 Min value discharge transducer bar -1
0x01BE 446 holding u16 /19 End scale value suction transducer bar 40
0x01BF 447 holding u16 /20 End scale value discharge transducer bar 40
0x01B7 439 holding u16 /33 Set point prevent high pressure function bar 0 40
0x01BB 443 holding u16 r34 Set point offset to change set from DI bar -99 99
0x01BD 445 holding u16 r11 Differential pressure for dead band by time bar 0 20
0x01B0 432 holding u16 r33 Condensing temperature delta for floating control °C/°F -40 150
0x01B8 440 holding u16 A16 High temp threshold probe B2 °C/°F -40 150
0x01B2 434 holding u16 A17 High temp threshold probe B3 °C/°F -40 150
0x01B1 433 holding u16 /00 Type of unit 0 2
0x01B4 436 holding u16 /01 Unit model 0 14
0x01C5 453 input u16 - Number of compressors 0 4
0x01C9 457 holding u16 /09 Number of fans 0 4
0x01C6 454 input u16 - Unit status 0 7
0x01C3 451 holding u16 r07 Minimum call time for compressor start (dead band) s 0 999
0x01CC 460 holding u16 r09 Minimum call time for compressor stop (dead band) s 0 999
0x01CA 458 holding u16 C01 Minimum compressor ON time s 0 999
0x01CE 462 holding u16 C02 Minimum compressor OFF time s 0 999
0x01CF 463 holding u16 C03 Minimum time between starts of different compressors s 0 999
0x01C7 455 holding u16 C05 Minimum time between starts of the same compressor s 0 999
0x01CB 459 holding u16 - Fan start delay (dead band) s 0 999
0x01CD 461 holding u16 - Fan stop delay (dead band) s 0 999
0x01C0 448 holding u16 A18 Liquid level alarm delay s 0 999
0x01C8 456 holding u16 - Minimum fan speed % 0 100
0x01C2 450 holding u16 /07 Number of compressors on in circuit 1 with probe damaged 0 4
0x01C1 449 holding u16 /08 Number of compressors on in circuit 2 with probe damaged 0 2
0x01C4 452 holding u16 /12 Number of fans on with probe damaged 0 4
0x01D5 469 input u16 - Version of the application
0x01D9 473 holding u16 /35 Type of refrigerant 0 11
0x01D6 470 holding u16 /03 Capacity of compressor 1 0 500
0x01D3 467 holding u16 /04 Capacity of compressor 2 0 500
0x01DC 476 holding u16 /05 Capacity of compressor 3 0 500
0x01DA 474 holding u16 /06 Capacity of compressor 4 0 500
0x01DE 478 input u16 /11 Inverter readout % % 0 100
0x01DF 479 holding u16 /15 Multifunction DI configuration 0 12
0x01D7 471 holding u16 /16 Type of discharge probe 0 2
0x01DB 475 holding u16 /21 Type of probe B2 0 2
0x01DD 477 holding u16 /22 Type of probe B3 0 2
0x01D0 464 holding u16 /37 Delay restart after black out s 0 999
0x01D8 472 holding u16 C04 Min time between two stop calls for different compressors s 0 999
0x01D2 466 holding u16 C06 Time between compressor stop call with Prevent function s 0 999
0x01D1 465 holding u16 C07 Operating hour threshold for maintenance h x10 0 999
0x01D4 468 input u16 C08 Compressor 1 hours h x10 0 999
0x01E5 485 input u16 C10 Compressor 2 hours h x10 0 999
0x01E9 489 input u16 C12 Compressor 3 hours h x10 0 999
0x01E6 486 input u16 C14 Compressor 4 hours h x10 0 999
0x01E3 483 holding u16 r05 Type of compressor rotation 0 2
0x01EC 492 holding u16 r06 Type of compressor control 0 2
0x01EA 490 holding u16 r08 Maximum call for compressor starts in dead band by time s 0 999
0x01EE 494 holding u16 r10 Maximum call for compressor stops in dead band by time s 0 999
0x01EF 495 holding u16 r20 Type of fan rotation 0 1
0x01E7 487 holding u16 r21 Type of fan control 0 2
0x01EB 491 holding u16 r22 Integral time for P+I fan control s 0 999
0x01ED 493 holding u16 r23 Time between 2 fans starts in dead band s 0 999
0x01E0 480 holding u16 r24 Time between 2 fans stops in dead band s 0 999
0x01E8 488 holding u16 r27 Inverter speed up time s 0 999
0x01E2 482 holding u16 r28 Inverter ramp up time s 0 999
0x01E1 481 holding u16 r29 Minimum inverter output % 0 100
0x01E4 484 holding u16 r30 Maximum inverter output % 0 100
0x01F5 501 holding u16 r31 Triac impulse duration ms 0 10
0x01F9 505 holding u16 A02 High suction pressure 1 alarm delay s 0 999
0x01F6 502 holding u16 A04 Low suction pressure 1 alarm delay s 0 999
0x01F3 499 holding u16 A06 High suction pressure 2 alarm delay s 0 999
0x01FC 508 holding u16 A08 Low suction pressure 2 alarm delay s 0 999
0x01FA 506 holding u16 A11 Low discharge pressure alarm delay s 0 999
0x01FE 510 holding u16 A12 Compressor thermal overload alarm delay s 0 999
0x01FF 511 holding u16 A13 Prevent time in which no compressor starts are enabled m 0 99
0x01F7 503 holding u16 A14 Prevent time in which the activation signals the alarm m 0 999
0x01FB 507 holding u16 A15 Time to reset prevent alarm m 0 99
0x01FD 509 holding u16 A20 Alarm signal delay s 0 999
0x01F0 496 holding u16 A21 Time to change low pressure alarm from automatic to manual s 0 999
0x01F1 497 input u16 Operating percentage of first capacity controlled compressor
0x01F4 500 input u16 Operating percentage of second capacity controlled compressor

Общие регистры

Общие для всех Modbus-устройств Wiren Board регистры
Адрес Параметры регистра Описание Значения
Dec Hex Тип Доступ Формат
104­-105 0x0068 - 0x0069 Input RO u32 Время работы с момента загрузки секунды
121 0x0079 Input RO u16 Текущее напряжение питания мВ
110 0x006E Holding RW u16 Скорость порта RS-485.
Настройка параметров подключения по RS-485 		x100, Боды
12 — 1200 бит/с,
24 — 2400 бит/с,
48 — 4800 бит/с,
96 — 9600 бит/с,
192 — 19 200 бит/с,
384 — 38 400 бит/с,
576 — 57 600 бит/с,
1152 — 115 200 Кбит/с
111 0x006F Holding RW u16 Настройка бита чётности порта RS-485 0 — нет бита чётности (none),
1 — нечётный,
2 — чётный
112 0x0070 Holding RW u16 Количество стоп-битов порта RS-485 1, 2
113 0x0071 Holding RW u16 Время перед отправкой ответа на modbus запрос 0 - 254 мс
114 0x0072 Holding RW u16 Режим непрерывного чтения регистров с зазором 0 - отключен
1 - включен
2 - включение сохраняется после перезагрузки
128 0x0080 Holding RW u16 Modbus-адрес устройства (подробнее)
120 0x0078 Holding RW u16 Перезагрузка устройства без сохранения состояния любое, отличное от 0 перезагружает устройство
129 0x0081 Holding RW u16 Перевод в режим обновления прошивки на 2 минуты любое, отличное от 0 переводит устройство в режим обновления прошивки
130 0x0082 Holding RW u8 Отключение индикатора состояния 0 - активен,
1 - отключен
123 0x007B Input RO u16 Напряжение на микроконтроллере мВ
124 0x007C Input RO u16 Внутренняя температура микроконтроллера x0.1, °C
200-205 0x00C8 - 0x00CD Input RO string Модель устройства
206-219 0x00CE - 0x00DB Input RO string Расширение модели устройства. Для новых устройств WB-LED и WB-MAI6 поле поддерживается изначально, для остальных - в прошивках с "быстрым Modbus". Для чтения модели устройства нужно читать диапазон из 20 регистров (200 - 219). Если устройство возвращает ошибку Illegal Data Address - читать 6 регистров (200 - 205).
220-248 0x00DC - 0x00F8 Input RO string Хэш коммита и название ветки откуда собрана прошивка (2 символа в регистре)
250-265 0x00FA - 0x0109 Input RO string Версия прошивки
266-269 0x010A - 0x010D Input RO u64 Расширение серийного номера
270-271 0x010E - 0x010F Input RO u32 Серийный номер
290-301 0x0122 - 0x012D Holding RO string Сигнатура прошивки
330-336 0x014A - 0x0150 Holding RO string Версия загрузчика


Версия прошивки в устройствах с «Быстрым Modbus»

В устройствах, поддерживающих Быстрый Modbus, используется другой формат обозначения версии прошивки.

  • Диапазон регистров «Модель устройства» расширен до 20 регистров.
  • Версия формируется согласно semver и имеет формат MAJOR.MINOR.PATCH с опциональным суффиксом (-rc|+wb)SUFFIX:
    суффикс -rc означает, что прошивка предназначена для тестирования и может быть нестабильной. Хранится в регистре с отрицательным знаком;
    суффикс +wb добавляется, когда к прошивке, зафиксированной в релизе, требуется выпустить фикс. Хранится в регистре с положительным знаком.
  • Цифры версии доступны по отдельности в формате u16 (для суффикса - s16), регистры 320-323.
  • Доступно число u32, содержащее комбинацию цифр версии и позволяющее за одно сравнение понять, увеличилась или уменьшилась версия прошивки:
    число рассчитывается по формуле
    if (SUFFIX >= 0) {
    SUFFIX = SUFFIX + 128;
} else {
    SUFFIX = -1 - SUFFIX;
}
VERSION = (MAJOR << 24) + (MINOR << 16) + (PATCH << 8) + SUFFIX;
    число доступно для чтения в little-endian и big-endian форматах;
    число для более свежей версии всегда будет больше, чем для предыдущей, в том числе, когда прошивка переходит из тестовой в стабильную.
    Таким образом обеспечивается корректное сравнение версий:
    1.2.3-rc1 < 1.2.3-rc10 < 1.2.3 < 1.2.3+wb1 < 1.2.3+wb10.


Регистры для хранения версии прошивки в устройствах с быстрым Modbus
Адрес Параметры регистра Описание Значения
Dec Hex Тип Доступ Формат
200-219 0x00C8 - 0x00DB Input RO string Модель устройства
320 0x0140 Input RO u16 Версия прошивки в числовом формате MAJOR
321 0x0141 MINOR
322 0x0142 PATCH
323 0x0143 s16 SUFFIX
324-325 0x0144 - 0x0145 Input RO u32 Версия прошивки в числовом формате
326-327 0x0146 - 0x0147 Input RO u32 Версия прошивки в Big Endian формате

| 816­-818 || 0x0330 ­- 0x0332 || Input || RO || u16 || Используются для определения модели контроллера || |}

Источник — https://wirenboard.com/wiki/index.php?title=WB-REF-U-CR_Modbus_Registers&oldid=64556