WBE-MICROSD Extension Module/en: различия между версиями
(Новая страница: «__NOTOC__ thumb|300px| MicroSD extension module») |
|||
| (не показано 16 промежуточных версий этого же участника) | |||
| Строка 1: | Строка 1: | ||
<languages/> | <languages/> | ||
{{DISPLAYTITLE:MicroSD extension module (WBE-MICROSD)}} | <!--{{DISPLAYTITLE:MicroSD extension module (WBE-MICROSD)}}--> | ||
| Строка 6: | Строка 6: | ||
[[File:MEM.png|thumb|300px| MicroSD extension module]] | [[File:MEM.png|thumb|300px| MicroSD extension module]] | ||
== | == Hardware == | ||
Can be installed only to MOD1 extension slot. | |||
microSD | the microSD card is inserted into the slot under the top cover of the controller. | ||
The module comes without a microSD card! | |||
Supported cards: microSD, microSDHC. | |||
Maximum interface speed supported: "high speed" (18MB/s for revision 5.3, 4.5 MB/s for revision 5.6). | |||
Standard UHS is not supported (card is working in the mode of "high speed"). | |||
== | == Pinout == | ||
O1-O3 terminals are not used. | |||
== | ==Configuration== | ||
[[File:Hwconf microsd.jpg|thumb|300px| | [[File:Hwconf microsd.jpg|thumb|300px|Configuration]] | ||
Configuration is done in the web interface. Section Configs => Hardware Modules Configuration. | |||
Next, in Internal slot 1 select "WBE-MICROSD" and click Save. | |||
Для аппаратной [[Wiren Board 5: Аппаратные ревизии | | Для аппаратной нужно выбрать "WBE-MICROSD: microSD module". | ||
For the hardware WB [[Wiren Board 5: Аппаратные ревизии/en |rev 5.3]], select "WBE-MICROSD: microSD module". | |||
For [[Wiren Board 5: Аппаратные ревизии/en | rev.5.6]] - "WBE-MICROSD: microSD module (WB 5.6)". | |||
The device is detected immediately, no reboot is required. | |||
== | == Operation == | ||
The memory card is defined in the system as mmc1. The entire card is available as /dev/mmcblk1 is the card partitions as /dev/mmcblk1p0 etc. | |||
== | == Compatibility table == | ||
{| class="wikitable" | {| class="wikitable" | ||
! | !Controller | ||
! | !Revision | ||
!MOD1 | !MOD1 | ||
!MOD2 | !MOD2 | ||
! | !Purchase part number | ||
|- | |- | ||
|Wiren Board 5 | |Wiren Board 5 | ||
Текущая версия на 19:36, 1 июля 2019
Hardware
Can be installed only to MOD1 extension slot.
the microSD card is inserted into the slot under the top cover of the controller. The module comes without a microSD card!
Supported cards: microSD, microSDHC. Maximum interface speed supported: "high speed" (18MB/s for revision 5.3, 4.5 MB/s for revision 5.6). Standard UHS is not supported (card is working in the mode of "high speed").
Pinout
O1-O3 terminals are not used.
Configuration
Configuration is done in the web interface. Section Configs => Hardware Modules Configuration. Next, in Internal slot 1 select "WBE-MICROSD" and click Save.
Для аппаратной нужно выбрать "WBE-MICROSD: microSD module". For the hardware WB rev 5.3, select "WBE-MICROSD: microSD module".
For rev.5.6 - "WBE-MICROSD: microSD module (WB 5.6)".
The device is detected immediately, no reboot is required.
Operation
The memory card is defined in the system as mmc1. The entire card is available as /dev/mmcblk1 is the card partitions as /dev/mmcblk1p0 etc.
Compatibility table
| Controller | Revision | MOD1 | MOD2 | Purchase part number |
|---|---|---|---|---|
| Wiren Board 5 | 5.3 | + | - | WBE-MICROSD |
| Wiren Board 5 | 5.6 | + | - | WBE-MICROSD |