WBIO-DO-R10A-8 Relay Module/en: различия между версиями
(Новая страница: «== Connection to the controller == See Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in…») |
(Новая страница: «300px|thumb|right|Controls of the module in the web interface») |
||
| Строка 86: | Строка 86: | ||
See [[Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in the web interface of the controller]]. In the Module type field, select '''WBIO-DO-RxA-8: 8 Channel Relay I/O module'''. In the web interface the relay will be presented by the controls of EXT'''x'''_R3A1 — EXT'''x'''_R3A8 of the Discrete I/O devices. The corresponding MQTT-topics: /devices/wb-gpio/controls/EXT'''x'''_R3A'''y'''. | See [[Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in the web interface of the controller]]. In the Module type field, select '''WBIO-DO-RxA-8: 8 Channel Relay I/O module'''. In the web interface the relay will be presented by the controls of EXT'''x'''_R3A1 — EXT'''x'''_R3A8 of the Discrete I/O devices. The corresponding MQTT-topics: /devices/wb-gpio/controls/EXT'''x'''_R3A'''y'''. | ||
[[File:Wbio-do-rxa-8_controls.png|300px|thumb|right| | [[File:Wbio-do-rxa-8_controls.png|300px|thumb|right|Controls of the module in the web interface]] | ||
== Подключение нагрузки== | == Подключение нагрузки== | ||
Версия 17:27, 15 июля 2019
Purpose
Control of lighting, motors, contactors.
Technical specifications
Contains 8 HF32F-G relays (Datasheet) with SPST contacts configuration (two contacts per relay: NO/COM) switching the corresponding 8 outputs. The outputs are output to screw clamps designed for a maximum current of 20 A.
Permissible current up to 7A per channel. The module has protection against sparking of the contacts.
Our detailed article in russian on habr.com about the choice of relay parameters for the switched load: https://habr.com/ru/company/wirenboard/blog/422197/
| Parameter | Value |
|---|---|
| Number of outputs | 8 |
| Output type | mechanical relay |
| Contact configuration | SPST, normally open
states:
|
| Maximum switching voltage, alternating current | 250 V |
| Maximum switching voltage, direct current | 30 Volts |
| Maximum switching current, per channel (*) | 7 A |
| The channel resistance in the open state | < 100 megohms |
| Voltage isolation between the controller and the output | 1500 V (RMS.) |
| Lifetime: number of switches
for load 10 A 230 V AC, cos φ = 1 |
100 000 |
| Module type | "O" (non-inverted address scheme) |
| Maximum power consumption | 1 W |
| Width, DIN units | 3 |
| Size | 53,3x90,2x57,5 mm |
*) Maximum switching current is specified for 230 VAC resistive load.
| Terminals and wire section | |
|---|---|
| The recommended wire cross section with pin bushing insulated tip, mm2 | 2,5 |
| Standard sleeve length of pin bushing insulated tip, mm | 8 |
| Tightening torque of screws, Н∙м | 0,5 |
Connection to the controller
See Activating the modules in the web interface of the controller. In the Module type field, select WBIO-DO-RxA-8: 8 Channel Relay I/O module. In the web interface the relay will be presented by the controls of EXTx_R3A1 — EXTx_R3A8 of the Discrete I/O devices. The corresponding MQTT-topics: /devices/wb-gpio/controls/EXTx_R3Ay.
Подключение нагрузки
Реле подключаются в разрыв фазы.
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WBIO-AO-10V-8.
Corel Draw 2018: WBIO-AO-10V-8.cdr.zip
Corel Draw PDF: WBIO-AO-10V-8.cdr.pdf
Autocad 2013 DXF: WBIO-AO-10V-8.dxf.zip
Autocad PDF: WBIO-AO-10V-8.pdf