Wiren Board 6/en: различия между версиями

[[RS-485:Настройка через веб-интерфейс/en| Setting up connection]] of the devices is carried out in the web interface.

Basically in Wiren Board,[[WB-mqtt-serial driver/en| WB-mqtt-serial driver]] works through the system of [[MQTT/en| MQTT]]-messages with connected RS-485 devices.

* [[ADC/en |ADC]]with a measurement range of 0 — 28 V

* [[DI | Discrete input ]] — is triggered when the voltage at the terminal is 5 V

Multiple DS18B20 temperature sensors can be connected to each channel via a loop: depending on the loop length, the maximum number of sensors is 10 to 20 (the limit is 20 sensors per 5m cable connected by a star). Additional sensors can be connected via the [[Wiren_Board_6:_Модуль_расширения_1-Wire|WBE2-I-1-WIRE]] module.

Some terminal blocks can be used to perform more than one function. See the detailed description in the [[Мультиплексирование портов/en| Port multiplexing]] article.

! colspan="6"| Upper row, right block

In the 6.3 revision of Wiren Board controller terminals of "type 250" applied as front-end terminals.

[[Отладочный порт/en/ Debug port]] — by connecting to it, you can directly access the controller console. Through it you can also interact with the bootloader and monitor the operating system boot (serial console).  

For backup power, you can connect the internal extension module [[WBMZ-BATTERY2/en | WBMZ-BATTERY2 ]] with Li-Ion (Li-Pol) battery.'''Important: when the controller is supplied with a battery module, the controller does not turn on immediately when the power is supplied. To turn it on, press the power button of the module under the top cover of the controller. See article [[WBMZ2-BATTERY/en]].'''

[[Wirenboard6:InstallingOnTheRemoteSite/en|Wiren Board 6:Installing On The Remote Site]]

[[Special:MyLanguage/WB 6: Errata/en | Hardware errors/features of Wiren Board 6 ]] found in the operation of the controller.

The table of processor and GPIO signals match on the board according to the revisions: [[Wiren Board 6.0.1:a List of GPIO/en|Wiren Board 6.0.1]], [[Wiren Board 6.1:a List of GPIO/en|Wiren Board 6.1]],

[[Wiren Board 6.2:GPIO/en|Wiren Board 6.2  and above]]

[[Обновление прошивки/en|Обновление прошивки]]. To reset the Wiren Board 6 to factory settings (factory reset), use the instructions in the section [[Обновление прошивки/en#Factory reset]]

[[WB6_root_password_recovery|Wiren Board 6: WB6 root password recovery]]

|| Scripts || Rules wb-rules in JavaScript, editing via Web-interface. Support for node-RED scripting

| [[Media:{{#var:FileName2}}.cdr.zip|{{#var:FileName2}}.cdr.zip]] || [[Media:{{#var:FileName2}}.cdr.pdf|{{#var:FileName2}}.cdr.pdf]] || We haven't prepared a blueprint for this device yet. You can [https://support.wirenboard.com/new-topic?category=featurerequests/blueprints&title=Чертеж%20устройства%20{{#var:ProductName2}} send request for the device drawing "{{#var:ProductFullName2}}"] on our support portal (registration required). || —

| [[Media:{{#var:FileName4}}.cdr.zip|{{#var:FileName4}}.cdr.zip]] || [[Media:{{#var:FileName4}}.cdr.pdf|{{#var:FileName4}}.cdr.pdf]] ||We haven't prepared a blueprint for this device yet. You can [https://support.wirenboard.com/new-topic?category=featurerequests/blueprints&title=Чертеж%20устройства%20{{#var:ProductName4}} send request for the device drawing "{{#var:ProductFullName4}}"] on our support portal (registration required).|| —

| [[Media:{{#var:FileName5}}.cdr.zip|{{#var:FileName5}}.cdr.zip]] || [[Media:{{#var:FileName5}}.cdr.pdf|{{#var:FileName5}}.cdr.pdf]] || We haven't prepared a blueprint for this device yet. You can [https://support.wirenboard.com/new-topic?category=featurerequests/blueprints&title=Чертеж%20устройства%20{{#var:ProductName5}} send request for the device drawing "{{#var:ProductFullName5}}"] on our support portal (registration required). || —