RS-485/en: различия между версиями
(Новая страница: «File:rs-485-setup-configs.png|thumb|right|300 px|Configuration takes place via the ''Configs'' [[RS-485:Настройка через веб-интерфейс|…») |
|||
(не показано 12 промежуточных версий этого же участника) | |||
Строка 1: | Строка 1: | ||
<languages/> | <languages/> | ||
__NOTOC__ | __NOTOC__ | ||
'''RS-485''' | '''RS-485''' - two-wire bus communication standard. | ||
Up to 256 devices can be connected to the bus. Transmission speed is up to 115200 bit/s.Line length is up to 1200 meters. | Up to 256 devices can be connected to the bus. Transmission speed is up to 115200 bit/s.Line length is up to 1200 meters. | ||
Via the RS-485 bus you can connect to the Wiren Board controller: | |||
* [[Special:MyLanguage/Периферийные устройства с интерфейсом RS-485 серии WB-xxxx | devices of our production with the RS-485 interface]], | * [[Special:MyLanguage/Периферийные устройства с интерфейсом RS-485 серии WB-xxxx | devices of our production with the RS-485 interface,]], | ||
* Mercuriy and Milur counters, | * Mercuriy and Milur counters, | ||
* [[Поддерживаемые устройства | * [[Special:MyLanguage/Поддерживаемые устройства#Подключаемые по RS-485 | some other devices.]]. | ||
Строка 15: | Строка 15: | ||
See article [[RS-485:Основы функционирования интерфейса RS-485|Basics of RS-485 interface operation]]. | See article [[RS-485:Основы функционирования интерфейса RS-485|Basics of RS-485 interface operation]]. | ||
The Wiren Board devices use the Modbus Protocol on top of the RS-485. [[Протокол Modbus | See article RS-485:Basics of RS-485 interface operation. | ||
The Wiren Board devices use the Modbus Protocol on top of the RS-485. [[Special:MyLanguage/Протокол Modbus|Протокол Modbus]]. | |||
==How to lay the bus correctly== | ==How to lay the bus correctly== | ||
See article[[RS-485:Физическое подключение | See article[[RS-485:Физическое подключение| RS-485:Physical connection.]]. | ||
Строка 29: | Строка 31: | ||
== | == Работа с портом RS-485 контроллера из собственного ПО == | ||
* | *Стандартно в Wiren Board с подключёнными по RS-485 устройствами работает [[Special:MyLanguage/Драйвер wb-mqtt-serial|Драйвер wb-mqtt-serial]] (ранее ''wb-homa-modbus''). Он позволяет работать с подключёнными устройствами RS-485 через систему [[Special:MyLanguage/MQTT|MQTT]]-сообщений. | ||
*: | *:Если вы хотите работать с портом RS-485 напрямую, не используя этот драйвер - отключите его, иначе он будет писать в порт RS-485. | ||
*[[Работа с последовательным портом из Linux | *[[Special:MyLanguage/Работа с последовательным портом из Linux|Работа с последовательным портом из Linux]] | ||
*[[Доступ к порту RS-485 контроллера Wiren Board с компьютера | *[[Special:MyLanguage/Доступ к порту RS-485 контроллера Wiren Board с компьютера|Доступ к порту RS-485 контроллера Wiren Board с компьютера]] | ||
*[[UART_Communication_Settings | *[[Special:MyLanguage/UART_Communication_Settings|Настройка параметров обмена данными по RS-485 для modbus-устройств Wiren Board]] |
Версия 18:51, 23 апреля 2019
RS-485 - two-wire bus communication standard.
Up to 256 devices can be connected to the bus. Transmission speed is up to 115200 bit/s.Line length is up to 1200 meters.
Via the RS-485 bus you can connect to the Wiren Board controller:
- devices of our production with the RS-485 interface,,
- Mercuriy and Milur counters,
- some other devices..
Basics of the RS-485 interface
See article Basics of RS-485 interface operation.
See article RS-485:Basics of RS-485 interface operation.
The Wiren Board devices use the Modbus Protocol on top of the RS-485. Протокол Modbus.
How to lay the bus correctly
See article RS-485:Physical connection..
Adding a device to the web interface
After connecting the RS-485 device to the controller, you need to configure it to appear in the web interface. See the instructions in article RS-485:Настройка через веб-интерфейс.
Работа с портом RS-485 контроллера из собственного ПО
- Стандартно в Wiren Board с подключёнными по RS-485 устройствами работает Драйвер wb-mqtt-serial (ранее wb-homa-modbus). Он позволяет работать с подключёнными устройствами RS-485 через систему MQTT-сообщений.
- Если вы хотите работать с портом RS-485 напрямую, не используя этот драйвер - отключите его, иначе он будет писать в порт RS-485.
- Работа с последовательным портом из Linux
- Доступ к порту RS-485 контроллера Wiren Board с компьютера
- Настройка параметров обмена данными по RS-485 для modbus-устройств Wiren Board