WBIO-DI-DR-8 I/O Module/en: различия между версиями

Нет описания правки
(Новая страница: «Such devices form a signal by closing two wires that are suitable for them. Connect one wire to the GND terminal of the module. Connect the second wire to the Dx…»)
 
(не показано 7 промежуточных версий 2 участников)
Строка 1: Строка 1:


{{DisplayTitle: Discrete inputs dry contact  module (WBIO-DI-DR-8)}} {{#vardefine:ProductFullName1|Discrete inputs module for dry contact signals WBIO-DI-DR-8}} {{#vardefine:FileName1|WBIO-DI-DR-8}} {{#vardefine:ProductName1|WBIO-DI-DR-8}}
{{DISPLAYTITLE: Discrete inputs dry contact  module (WBIO-DI-DR-8)}} {{#vardefine:ProductFullName1|Discrete inputs module for dry contact signals WBIO-DI-DR-8}} {{#vardefine:FileName1|WBIO-DI-DR-8}} {{#vardefine:ProductName1|WBIO-DI-DR-8}}
[[File:WBIO-DI-DR-8-small-crop.png|200px|thumb|WBIO-DI-DR-8 Module]]
[[File:WBIO-DI-DR-8-small-crop.png|200px|thumb|WBIO-DI-DR-8 Module]]
'''[https://wirenboard.com/en/product/wbio-di-dr-8/ Buy online]'''
This model is discontinued​.[[WBIO-DI-WD-14_I/O_Module/en| WBIO-DI-WD-14]] is a recommended replacement.
'''[https://wirenboard.com/ru/product/WBIO-DI-WD-14/ Buy WBIO-DI-WD-14 online]'''


== Applicability ==
== Applicability ==
Строка 80: Строка 81:
Such devices form a signal by closing two wires that are suitable for them. Connect one wire to the GND terminal of the module. Connect the second wire to the Dx terminal. Some counters have a pulse output on the optocoupler, then the two wires have a polarity - "plus" and "minus". In this case, minus is connected to GND, plus - to Dx.
Such devices form a signal by closing two wires that are suitable for them. Connect one wire to the GND terminal of the module. Connect the second wire to the Dx terminal. Some counters have a pulse output on the optocoupler, then the two wires have a polarity - "plus" and "minus". In this case, minus is connected to GND, plus - to Dx.


'''Устройства с выходом открытый коллектор.'''
'''Devices with open collector output.'''


Устройство и модуль должны иметь общую землю. Выход "открытый коллектор" подключите к клемме Dx.  
Both device and controller must be connected to the common grounding bus. Connect the "open collector" output to the Dx terminal.  


Входы модуля гальванически развязаны от контроллера. Поэтому земли GND модуля и контроллера могут быть разными.
The module inputs are galvanically isolated from the controller. Therefore, the ground GND of the module and the controller may be different.


[[Файл:DI.png|300px|thumb|none|Цифровые входы DI]]
[[Файл:DI.png|300px|thumb|none|Digital inputs DI]]


== Изображения и чертежи устройства ==
== Images and drawings of the device ==
{{Wbincludes:WBPictures|1}}
{{Wbincludes:WBPictures|1}}
12 063

правки