WBIO-DI-DR-14 I/O Module/en: различия между версиями
(Новая страница: «circuit to the ground |- |Operation condition |GND input lockout circuit |- |Tripping current |1 mA |- |Minimum pulse width to trigger |10 MS |- |Minimum time bet…») |
(Новая страница: «{| class="wikitable" !colspan="2" | '''Terminals and wire section''' |- || The recommended wire cross section with pin bushing insulated tip, mm<sup>2</sup> ||…») |
||
Строка 61: | Строка 61: | ||
{| class="wikitable" | {| class="wikitable" | ||
!colspan="2" | ''' | !colspan="2" | '''Terminals and wire section''' | ||
|- | |- | ||
|| | || The recommended wire cross section with pin bushing insulated tip, mm<sup>2</sup> || 0,75 — 1 | ||
|- | |- | ||
|| | || Standard sleeve length of pin bushing insulated tip, mm || 8 | ||
|- | |- | ||
|| | ||Tightening torque of screws, Н∙м || 0,2 | ||
|- | |- | ||
|} | |} |
Версия 12:54, 3 июля 2019
Внимание: Отображаемое название «14 digital dry contact inputs module (WBIO-DI-DR-14)» переопределяет ранее заданное отображаемое название «WBIO-DI-DR-14 I/O Module». The model is discontinued. Recommended replacement is WBIO-DI-WD-14
Purpose
Connection of pulse counters, buttons, switches, sensors with dry contact output.
Technical specifications
It contains 14 inputs for connection of dry contacts, which are united in two groups of 7 inputs with group galvanic isolation. The scheme of inputs is shown in the figure. The terminal is supplied with ~ 4.5 V, when the small (1 mA) current is supplied to the ground, causing the operation of the input.
Parameter | Value |
---|---|
Number of inputs | 14 |
Isolated input groups | 2 |
Input type | dry contact,
the opening by the current at circuit to the ground |
Operation condition | GND input lockout circuit |
Tripping current | 1 mA |
Minimum pulse width to trigger | 10 MS |
Minimum time between consecutive signals | 5 MS |
Voltage "wetting" | 4.5 V |
Module type | "I" (inverted address scheme) |
Maximum power consumption | 0.1 W |
Width, DIN units | 2 |
Size | 36,3x90,2x57,5 mm |
Terminals and wire section | |
---|---|
The recommended wire cross section with pin bushing insulated tip, mm2 | 0,75 — 1 |
Standard sleeve length of pin bushing insulated tip, mm | 8 |
Tightening torque of screws, Н∙м | 0,2 |
Подключение к контроллеру
Смотрите раздел Активирование в веб-интерфейсе контроллера
Подключение
Датчики/счетчики с импульсными выходами/кнопки.
Такие устройства формируют сигнал, замыкая подходящие к ним два провода. Подключите один провод к клемме GND модуля. Второй провод подключите к клемме Dx. Некоторые счетчики имеют импульсный выход на оптроне, тогда два провода имеют полярность - "плюс" и "минус". В таком случае минус подключается к GND, "плюс" к Dx.
Устройства с выходом открытый коллектор.
Устройство и модуль должны иметь общую землю. Выход "открытый коллектор" подключите к клемме Dx.
Входы модуля гальванически развязаны от контроллера. Поэтому земли GND модуля и контроллера могут быть разными.
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WBIO-DI-DR-14.
Corel Draw 2018: WBIO-DI-DR-14.cdr.zip
Corel Draw PDF: WBIO-DI-DR-14.cdr.pdf
Autocad 2013 DXF: WBIO-DI-DR-14.dxf.zip
Autocad PDF: WBIO-DI-DR-14.pdf