WBIO-DI-DR-14 I/O Module/en: различия между версиями
(Новая страница: «== Images and drawings of the device == {{WBPictures|1}}») |
(Новая страница: «== Connection== '''Sensors/counters with pulse outputs/buttons.'''») |
||
(не показано 5 промежуточных версий этого же участника) | |||
Строка 79: | Строка 79: | ||
'''Sensors/counters with pulse outputs/buttons.''' | '''Sensors/counters with pulse outputs/buttons.''' | ||
Такие устройства формируют сигнал, замыкая подходящие к ним два провода. Подключите один провод к клемме GND модуля. Второй провод подключите к клемме Dx. Некоторые счетчики имеют импульсный выход на оптроне, тогда два провода имеют полярность - "плюс" и "минус". В таком случае минус подключается к GND, "плюс" к Dx. | |||
''' | '''Устройства с выходом открытый коллектор.''' | ||
Устройство и модуль должны иметь общую землю. Выход "открытый коллектор" подключите к клемме Dx. | |||
Входы модуля гальванически развязаны от контроллера. Поэтому земли GND модуля и контроллера могут быть разными. | |||
[[Файл:DI.png|300px|thumb|none| | [[Файл:DI.png|300px|thumb|none|Цифровые входы DI]] | ||
== | == Изображения и чертежи устройства == | ||
{{Wbincludes:WBPictures|1}} | {{Wbincludes:WBPictures|1}} |
Версия 12:56, 3 июля 2019
Внимание: Отображаемое название «14 digital dry contact inputs module (WBIO-DI-DR-14)» переопределяет ранее заданное отображаемое название «WBIO-DI-DR-14 I/O Module». The model is discontinued. Recommended replacement is WBIO-DI-WD-14
Purpose
Connection of pulse counters, buttons, switches, sensors with dry contact output.
Technical specifications
It contains 14 inputs for connection of dry contacts, which are united in two groups of 7 inputs with group galvanic isolation. The scheme of inputs is shown in the figure. The terminal is supplied with ~ 4.5 V, when the small (1 mA) current is supplied to the ground, causing the operation of the input.
Parameter | Value |
---|---|
Number of inputs | 14 |
Isolated input groups | 2 |
Input type | dry contact,
the opening by the current at circuit to the ground |
Operation condition | GND input lockout circuit |
Tripping current | 1 mA |
Minimum pulse width to trigger | 10 MS |
Minimum time between consecutive signals | 5 MS |
Voltage "wetting" | 4.5 V |
Module type | "I" (inverted address scheme) |
Maximum power consumption | 0.1 W |
Width, DIN units | 2 |
Size | 36,3x90,2x57,5 mm |
Terminals and wire section | |
---|---|
The recommended wire cross section with pin bushing insulated tip, mm2 | 0,75 — 1 |
Standard sleeve length of pin bushing insulated tip, mm | 8 |
Tightening torque of screws, Н∙м | 0,2 |
Connection to controller
See activating the module in the web interface of the controller.
Connection
Sensors/counters with pulse outputs/buttons.
Такие устройства формируют сигнал, замыкая подходящие к ним два провода. Подключите один провод к клемме GND модуля. Второй провод подключите к клемме Dx. Некоторые счетчики имеют импульсный выход на оптроне, тогда два провода имеют полярность - "плюс" и "минус". В таком случае минус подключается к GND, "плюс" к Dx.
Устройства с выходом открытый коллектор.
Устройство и модуль должны иметь общую землю. Выход "открытый коллектор" подключите к клемме Dx.
Входы модуля гальванически развязаны от контроллера. Поэтому земли GND модуля и контроллера могут быть разными.
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WBIO-DI-DR-14.
Corel Draw 2018: WBIO-DI-DR-14.cdr.zip
Corel Draw PDF: WBIO-DI-DR-14.cdr.pdf
Autocad 2013 DXF: WBIO-DI-DR-14.dxf.zip
Autocad PDF: WBIO-DI-DR-14.pdf