WBIO-DO-R1G-16 1A Relay Module/en: различия между версиями
FuzzyBot (обсуждение | вклад) (Часть переводимой страницы WBIO-DO-R1G-16 I/O Module.) |
(Новая страница: «|- |Maximum switching voltage, alternating current |250 V |- |Maximum switching voltage, direct current |30 Volts |- |Maximum switching current, per channel (*) |…») |
||
(не показано 9 промежуточных версий 2 участников) | |||
Строка 79: | Строка 79: | ||
|} | |} | ||
<nowiki>*</nowiki>) | <nowiki>*</nowiki>) Максимальный коммутируемый ток указан для резистивной нагрузки 230 В переменного тока. | ||
<nowiki>**</nowiki>) | <nowiki>**</nowiki>) Расчётное значение | ||
{| class="wikitable" | {| class="wikitable" | ||
!colspan="2" | ''' | !colspan="2" | '''Клеммники и сечение проводов''' | ||
|- | |- | ||
|| | || Рекомендуемое сечение провода с НШВИ, мм<sup>2</sup> || 2,5 | ||
|- | |- | ||
|| | || Длина стандартной втулки НШВИ, мм || 8 | ||
|- | |- | ||
|| | || Момент затяжки винтов, Н∙м || 0,5 | ||
|- | |- | ||
|} | |} | ||
[[File:DIN 3U.png |300px|thumb|right| | [[File:DIN 3U.png |300px|thumb|right|Габаритные размеры]] | ||
== | == Подключение к контроллеру == | ||
Смотрите раздел [[Модули ввода-вывода#Активирование в веб-интерфейсе контроллера|Активирование в веб-интерфейсе контроллера]] | |||
== | == Подключение нагрузки == | ||
Реле подключаются в разрыв фазы. | |||
[[Файл:Relay outputs.png|400px|thumb|none| | [[Файл:Relay outputs.png|400px|thumb|none|Схема подключения]] | ||
== | |||
== Изображения и чертежи устройства == | |||
{{Wbincludes:WBPictures|1}} | {{Wbincludes:WBPictures|1}} |
Версия 16:33, 15 июля 2019
Purpose
Control of contactors, warning lights, etc.
Technical specifications
Contains 16 HF49FD relays [(Datasheet)] with the configuration of contacts SPST (two contacts on the relay: NO/COM).
The relays are combined into two groups of 8 pieces, each group has one common COM pin: the upper COM pin for relays K1 — K8 and the lower COM pin for relays K9 — K16. There's no connection between groups, so the first group can switch one voltage source, and the second - the other.
Rated channel current: 1 A. The module has protection against sparking of the contacts.
Our detailed article in russian on habr.com about the choice of relay parameters for the switched load: https://habr.com/ru/company/wirenboard/blog/422197/
Parameter | Value |
---|---|
Number of outputs | 16 |
Number of output groups | 2 |
Output type | mechanical relay |
Contact configuration | SPST, normally open
states:
|
Maximum switching voltage, alternating current | 250 V |
Maximum switching voltage, direct current | 30 Volts |
Maximum switching current, per channel (*) | 5 A |
Maximum switching current,
the channels in one group |
10 A |
The channel resistance in the open state | < 50 mW |
Voltage isolation between the controller and the output | 2000 V (RMS.) |
Lifetime: number of switches
for load 3 A 230 V AC, cos φ = 1 |
100 000 |
Lifetime: number of switches
for load 0.1 A 230 V AC, cos φ = 1 (**) |
1 000 000 |
Module type | "O" (non-inverted address scheme) |
Maximum power consumption | 1 W |
Width, DIN units | 3 |
Size | 53,3x90,2x57,5 mm |
*) Максимальный коммутируемый ток указан для резистивной нагрузки 230 В переменного тока.
**) Расчётное значение
Клеммники и сечение проводов | |
---|---|
Рекомендуемое сечение провода с НШВИ, мм2 | 2,5 |
Длина стандартной втулки НШВИ, мм | 8 |
Момент затяжки винтов, Н∙м | 0,5 |
Подключение к контроллеру
Смотрите раздел Активирование в веб-интерфейсе контроллера
Подключение нагрузки
Реле подключаются в разрыв фазы.
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WBIO-DO-R1G-16.
Corel Draw 2018: WBIO-DO-R1G-16.cdr.zip
Corel Draw PDF: WBIO-DO-R1G-16.cdr.pdf
Autocad 2013 DXF: WBIO-DO-R1G-16.dxf.zip
Autocad PDF: WBIO-DO-R1G-16.pdf