WBIO-DO-HS-8 Discrete Outputs/en: различия между версиями
FuzzyBot (обсуждение | вклад) (Часть переводимой страницы Модуль дискретных выходов (WBIO-DO-HS-8).) |
(Новая страница: «== Connection to the controller == See Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in…») |
||
(не показано 5 промежуточных версий 2 участников) | |||
Строка 72: | Строка 72: | ||
See [[Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in the web interface of the controller]] | See [[Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in the web interface of the controller]] | ||
== | == Подключение нагрузки == | ||
Требует подключения внешнего питания к клеммам '''Vin''' и '''GND''' (от 11 до 45В). | |||
Земля модуля должна быть соединена с землей контроллера! | |||
[[Файл:HSx.png|300px|thumb|none| High Side Outputs | [[Файл:HSx.png|300px|thumb|none|Схема работы модуля High Side Outputs. ]] | ||
== | == Изображения и чертежи устройства == | ||
{{Wbincludes:WBPicturesNoDrawing|1}} | {{Wbincludes:WBPicturesNoDrawing|1}} |
Версия 16:54, 15 июля 2019
Purpose
The module is designed to control low-voltage loads: relays, low-voltage motors, signal lamps, etc
Technical specifications
Contains 8 outputs such as "High Side Switch" - when you turn on channel Vin voltage is supplied to the output.
The module is based on BTS4880R chip.
The outputs are protected against overload, short circuit, overheating, spikes when controlling the inductive load.
Parameter | Value |
---|---|
Number of outputs | 8 |
Number of groups | 1 |
Output type | High Side Switch |
Switching voltage | 11 - 45 V DC |
Maximum switching current, per channel | 0.6 A |
Leakage current disabled output (each output) | <10 µa |
The channel resistance in the open state | 200 mOhm |
Module type | O (non-inverted addr.) |
Maximum power consumption | 0.025 W |
Width, DIN units | 2 |
Size | 36.3x90.2x57.5 mm |
Terminals and wire section | |
---|---|
Recommended wire cross-section with TSVI, mm2 | 0,75 — 1 |
Length of the standard sleeve NSVE, mm | 8 (10 for adjusting screwless terminal blocks) |
Torque of screws, N∙m | 0,2 (for screw terminals) |
Connection to the controller
See Activating the modules in the web interface of the controller
Подключение нагрузки
Требует подключения внешнего питания к клеммам Vin и GND (от 11 до 45В).
Земля модуля должна быть соединена с землей контроллера!
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WBIO-DO-SSR-8.
Corel Draw 2018: WBIO-DO-SSR-8.cdr.zip
Corel Draw PDF: WBIO-DO-SSR-8.cdr.pdf
Autocad 2013 DXF: Мы еще не подготовили чертеж этого устройства. Вы можете запросить чертеж устройства "Digital output module WBIO-DO-SSR-8" на портале техподдержки Wiren Board (необходима регистрация).