WB-MAO4 0-10V Modbus Analog Outputs/en: различия между версиями
(Новая страница: «The module has inputs for three hardware buttons.») |
|||
Строка 92: | Строка 92: | ||
"<u>The page is under development!</u>" | "<u>The page is under development!</u>" | ||
The module has inputs for three hardware buttons. | |||
Кнопка 1. Короткое нажатие – включение/выключение всех каналов. Длительное нажатие – плавное изменение яркости всех каналов. | Кнопка 1. Короткое нажатие – включение/выключение всех каналов. Длительное нажатие – плавное изменение яркости всех каналов. |
Версия 15:53, 19 июля 2019
The page is in development!
Purpose
4-channel lighting control module is designed to control lamps with interfaces 0-10V, PWM, as well as to control arbitrary load with the corresponding inputs.
The type of output signal: 0-10V or PWM c with an amplitude of 10V. Type of output signals is configured (for all channels at once).
The module is controlled from the controller or PC via the RS-485 bus by MODBUS commands, as well as by external buttons.
Technical specifications
- 4 channels 0-10V or 10V PWM
- PWM frequency up to 400 Hz.
- Supply voltage: 11 to 24 V.
- Power consumption: 0.3 W.
- Interface: RS485, Modus RTU
- RS-485 interface parameters are set programmatically (see register Card);
default: speed — 9600 bit/s; data — 8 bit; parity bit — no (N); stop bits — 2 - Save state when power is off
- Inputs for three buttons for channel control
- Size– 65*35*7 mm.
Operating conditions
- Air temperature from -40°C to +70°C;
- Relative humidity up to 95%, without moisture condensation.
Connection
The module is made in the unselfish version - the board is in a shrink tube.
RS-485 and control buttons are connected to the blue terminals:
- A and B - RS485 signal lines
- GND - ground RS-485 bus (if any)
- b1 and GND - color balance control button
- b2 and GND - brightness control button
Management
Bus parameters
Speed is 9600 bit/s, data - 8 bit, parity – no, stop bit - 2.
Commands supported by device
Command | command (dec) |
---|---|
READ_COIL | 1 |
WRITE_SINGLE_COIL | 5 |
WRITE_MULTI_COILS | 15 |
READ_HOLDING_REGISTERS | 3 |
WRITE_SINGLE_REGISTER | 6 |
WRITE_MULTI_REGISTERS | 16 |
Functions
Address change is broadcast (slave_id 0) team record (WRITE_SINGLE_REGISTER) to holding register with address 128 (0x80).
6 bytes signature lies at the address 200. The signature is unique for each device model and allows you to identify the model. To obtain the signatures necessary to fulfill READ_HOLDING_REGISTERS address 200 length 6. Writing to this area of memory is not supported and error 3 is returned when attempting to write to an invalid location.
LED control
The brightness of the channel is set by an 8-bit number (0-255). The physical brightness of the LEDs is set according to the logarithmic dimming curve.
The module uses pulse width modulation (PWM), bit depth: 12 bit, PWM frequency: 24 kHz.
"The page is under development!"
The module has inputs for three hardware buttons.
Кнопка 1. Короткое нажатие – включение/выключение всех каналов. Длительное нажатие – плавное изменение яркости всех каналов.
Кнопка 2. Длительное нажатие кнопки – плавное изменение цвета.
Отключить управление каналами с помощью кнопок можно, записав число 255(0xFF) в HOLDING_REGISTER по адресу 5.
В любом режиме работы, текущее состояние кнопок можно прочесть из HOLDING_REGISTER по адресу 6 и 7. 0 отпущена, 1 - нажата.
Карта регистров
Регистр / адрес | тип | чтение/запись | значение по-умолчанию | формат | назначение | Примечание |
---|---|---|---|---|---|---|
0 | holding | RW | - | 0-255 | Уровень канала G, логарифмическая кривая | |
1 | holding | RW | - | 0-255 | Уровень канала R, логарифмическая кривая | |
2 | holding | RW | - | 0-255 | Уровень канала B, логарифмическая кривая | |
5 | holding | RW | 0 | 0: стандартный режим, 0xFF: отключить управление | режим работы кнопок | |
6 | input | R | 1 - нажата, 0 - отпущена | состояние кнопки 1 | ||
7 | input | R | 1 - нажата, 0 - отпущена | состояние кнопки 2 | ||
9 | holding | RW | 74 (312.5 Hz) | freq = 24 kHz / (value + 1) | частота ШИМ | |
13 | holding | RW | 100 | x 10ms | Время плавного изменения цвета | |
0 | coil | RW | 0 | 0: 0-10V
1: PWM 10V |
Режим работы выходов | |
120 (0x78) | holding | RW | 0 | отличное от 0 | запись в регистр вызывает перезагрузку МК без сохранения состояния | не поддерживается |
121 (0x79) | input | R | - | mV | текущее напряжение питания модуля | не поддерживается |
128 (0x80) | holding | RW | 1 | Modbus-адрес устройства | все | |
200-206 | input | R | {'W','B','M','A,'O', 0} | сигнатура | все | |
220-241 | input | R | __date__ __time__ | дата сборки прошивки | все |