Перейти к содержанию

Навигация

Relay Module Modbus Management/en: различия между версиями

Relay Module Modbus Management/en (просмотреть исходный код)

Версия 23:09, 18 апреля 2020

693 байта убрано ,  4 года назад
Нет описания правки
 
(не показано 9 промежуточных версий этого же участника)
Строка 13: Строка 13:
===Relay operation in case of power failure ===
===Relay operation in case of power failure ===


Для устройств WB-MR существует возможность запоминать состояние выхода при отключении питания. Режим контролируется Modbus-регистром 6. Если в регистре записано значение '0', то состояние выходов не сохраниться и при подаче питания все реле буду выключены. Если в регистре записана единица, то после возобновления питания все включенные до аварии реле включатся снова.
In the latest firmware versions (starting with 1.5.3) for WB-MR devices, it is now possible to remember the output status when power is off. The mode is controlled by the Modbus register 6. If the register is set to '0', the state of the outputs will not be saved and all relays will be switched off when power is supplied. If the entry in the register unit, when the power is resumed everything is included before the crash relay is switched on again.
Этот функционал появился в модулях с прошивкой, начиная с версии 1.5.3.


=== Digital inputs ===
=== Digital inputs ===
Строка 29: Строка 28:
** '''Mapping-matrix''' (see detailed description below)
** '''Mapping-matrix''' (see detailed description below)


<div class="mw-translate-fuzzy">
The mode set separately for each channel. To select mode, write mode number to corresponding holding register, starting with register 9 for the first channel etc. You should keep default value in register 5.
The mode can be set separately for each channel. To do this, register 5 must have a value of "0", and the mode for each channel is written to the storage registers starting from address 9 for the first channel, etc.
</div>


<div class="mw-translate-fuzzy">
There could be no registers 9 etc. in outdated firmware. You can only set mode for all their channels at once. To do so, write corresponding number to holding register 5.
There is an outdated method - setting the mode for all channels at the same time. To do this, write the appropriate number in the storage register with address 5.
</div>


==== Mapping-matrix ====
==== Mapping-matrix ====
Строка 41: Строка 36:
Starting from firmware v.1.9.0, '''mode 2''' is also provided for individual channels-disable all outputs, and '''operating modes (4 and 5)''' in accordance with the mapping matrix (see below).In this and later versions of firmware versions modules have flexible settings of the interaction of inputs and outputs of relay modules using a special mapping matrix: a table in which for each input is encoded change of any relay output state when the state of this input changes. A detailed description can be found in [[I/O_Mapping_Matrix/en|I/O Mapping Matrix]].
Starting from firmware v.1.9.0, '''mode 2''' is also provided for individual channels-disable all outputs, and '''operating modes (4 and 5)''' in accordance with the mapping matrix (see below).In this and later versions of firmware versions modules have flexible settings of the interaction of inputs and outputs of relay modules using a special mapping matrix: a table in which for each input is encoded change of any relay output state when the state of this input changes. A detailed description can be found in [[I/O_Mapping_Matrix/en|I/O Mapping Matrix]].


= Карта регистров модулей реле =
= Relay module register card =
В таблице:
In table:
* '''x''' — количество релейных выходов;  
* '''x''' — number of relay outputs;  
* '''y''' — количество цифровых входов.
* '''y''' — number of digital inputs.
Для устаревших модулей WB-MRM2 (не путать с современными WB-MRM2-mini) карту регистров смотрите на отдельной странице [[WB-MRM2]].
For outdated WB-MRM2 devices (not to be confused with modern WB-MRM2-mini) find register card on separate page [[WB-MRM2]].


<div class="mw-translate-fuzzy">
{| border="1" class="wikitable" style="text-align:center; width:1000px;"
{| border="1" class="wikitable" style="text-align:center; width:1000px;"
!Register / address
!Register / address
Строка 67: Строка 61:
| 0  
| 0  
| style="text-align:left;" |
| style="text-align:left;" |
* '''0''': buttons without locking
default value should be kept
* '''1''': switch with lock
|| not used in modern firmware.<br>In outdated versions of firmware was used to set mode of interaction of digital inputs with relay outputs for all inputs at once.
* '''3''': disable interaction
|| not used in modern firmware.<br>In outdated versions of firmware was used to set mode of interaction of digital inputs with relay outputs for all inputs at once. Configuration values were the same as now used in registers 9 .. (9+'''x'''-1), but applied to all inputs at once.
|| mode of interaction of digital inputs with relay outputs. The input status registers and the pressure counter continue to operate in all modes. || The register was used in the old configuration mechanism. It is recommended to leave it set to 0 and the inputs are configured via the individual registers 9 .. (9+'''x'''-1)
|-
|-
| 6
| 6
Строка 81: Строка 74:
| 8 || holding || RW|| 0 || seconds || safe mode timeout ||
| 8 || holding || RW|| 0 || seconds || safe mode timeout ||
|-
|-
</div>


<div class="mw-translate-fuzzy">
| rowspan="3"  | 9 .. (9+'''x'''-1)  
| rowspan="3"  | 9 .. (9+'''x'''-1)  
| rowspan="3"  | holding  
| rowspan="3"  | holding  
Строка 92: Строка 83:
* '''1''': switch with lock
* '''1''': switch with lock
* '''3''': disable interaction  
* '''3''': disable interaction  
| rowspan="3" | single digital input interaction mode with corresponding relay output;
| rowspan="3" | mode of interaction between digital input and corresponding relay output.<br>There should be default value in register 5   
"0" should be written in register 5   
|
|
|-
|-
</div>




Строка 133: Строка 122:




| 20 .. (20+'''x'''-1) || holdreg || RW || 50 || 0 - 100 || время защиты от дребезга в миллисекундах || Начиная с прошивки 1.13.0
| 20 .. (20+'''x'''-1) || holdreg || RW || 50 || 0 - 100 || debouncing time in ms || Since firmware 1.13.0
|-
|-




<div class="mw-translate-fuzzy">
| 32 .. (32+'''y'''-1) || input || R|| 0 || 16-bit unsigned int || input counter 1 .. '''y''' ||  
| 32 .. (32+'''y'''-1) || input || R|| 0 || 16-bit unsigned int || input counter 1 .. '''y''' ||  
|-
|-
</div>
| 384-447 || holding || RW || 0 ||  ||  [[I/O_Mapping_Matrix|Mapping Matrix]] registers || Since firmware 1.9.0
|}




Строка 146: Строка 135:
{{:Common_Modbus_Registers}}
{{:Common_Modbus_Registers}}


Регистры настройки параметров обмена данными по RS-485 поддерживаются начиная с прошивки версии 1.6.0
Registers for setting data exchange parameters for RS-485 are supported since firmware 1.6.0.
Источник — https://wirenboard.com/wiki/Служебная:Сравнение_версий/37249...37270