WBIO-DO-SSR-8 Discrete Outputs Dry Contact/en: различия между версиями
(Новая страница: «400px|thumb|none|WBIO-DO-SSR-8 module == Device pictures == {{WBPictures|1}}») |
FuzzyBot (обсуждение | вклад) (Часть переводимой страницы Модуль дискретных выходов типа "сухой контакт" (WBIO-DO-SSR-8).) Метки: правка с мобильного устройства правка из мобильной версии |
||
(не показаны 4 промежуточные версии 2 участников) | |||
Строка 2: | Строка 2: | ||
[[Файл:WBIO-DO-SSR-8.png|200px|thumb|right|Модуль WBIO-DO-SSR-8]] | [[Файл:WBIO-DO-SSR-8.png|200px|thumb|right|Модуль WBIO-DO-SSR-8]] | ||
{{#vardefine:ProductFullName1|Модуль дискретных выходов типа "сухой контакт" WBIO-DO-SSR-8}} {{#vardefine:FileName1|WBIO-DO-SSR-8}} {{#vardefine:ProductName1|WBIO-DO-SSR-8}} | {{#vardefine:ProductFullName1|Модуль дискретных выходов типа "сухой контакт" WBIO-DO-SSR-8}} {{#vardefine:FileName1|WBIO-DO-SSR-8}} {{#vardefine:ProductName1|WBIO-DO-SSR-8}} | ||
'''[https://wirenboard.com/ | '''[https://wirenboard.com/en/product/WBIO-DO-SSR-8/ Buy online]''' | ||
==Purpose== | ==Purpose== | ||
Строка 53: | Строка 53: | ||
{| class="wikitable" | {| class="wikitable" | ||
!colspan="2" | | !colspan="2" | '''Terminals and wire section''' | ||
|- | |- | ||
|| Recommended wire cross-section with TSVI, mm<sup>2</sup>|| 0,75 — 1 | || Recommended wire cross-section with TSVI, mm<sup>2</sup>|| 0,75 — 1 | ||
Строка 66: | Строка 66: | ||
== Connection to controller == | == Connection to controller == | ||
See [[Модули_ввода-вывода/en#Activating the modules in the controller web interface|activating the module in the web interface of the controller]]. The relay will be presented by the controls of EXT | See [[Модули_ввода-вывода/en#Activating the modules in the controller web interface|activating the module in the web interface of the controller]]. The relay will be presented by the controls of EXT'''x'''_K1 — EXT'''x'''_K8 of the Discrete I/O device in the web interface. The corresponding MQTT-topics: /devices/wb-gpio/controls/EXT'''x'''_K'''y'''. | ||
== Load connection== | == Load connection== |
Текущая версия на 13:08, 22 апреля 2021
Purpose
Designed for control of low-voltage load, devices with inputs for "dry contacts". Devices may not have common ground with the controller.
Specifications
The module contains 8 independent channels of optorele SPST configuration (normally open).
Each channel has built-in protection against voltage surges when switching inductive load (TVS for 30V).
Parameter | Value |
---|---|
Number of outputs | 8 |
Output type | optorele |
Contact configuration | SPST (normally open) |
Maximum switching voltage | 30 V AC and DC |
Maximum switching current, per channel | 400 mA |
The channel resistance in the open state | < 2 Ohms |
Voltage isolation between the controller and the output | 1500 V (RMS) |
Module type | "O" (non-inverted address scheme) |
Maximum power consumption | 0.2 W |
Width, DIN units | 2 |
Size | 36,3x90,2x57,5 mm |
Terminals and wire section | |
---|---|
Recommended wire cross-section with TSVI, mm2 | 0,75 — 1 |
Length of the standard sleeve NSVE, mm | 8 (10 for adjusting screwless terminal blocks) |
Torque of screws, N∙m | 0,2 (for screw terminals) |
Connection to controller
See activating the module in the web interface of the controller. The relay will be presented by the controls of EXTx_K1 — EXTx_K8 of the Discrete I/O device in the web interface. The corresponding MQTT-topics: /devices/wb-gpio/controls/EXTx_Ky.
Load connection
Each pair of outputs is galvanically isolated from the others. No polarity.
Device pictures
По ссылкам ниже вы можете скачать изображения и чертежи устройства WBIO-DO-SSR-8.
Corel Draw 2018: WBIO-DO-SSR-8.cdr.zip
Corel Draw PDF: WBIO-DO-SSR-8.cdr.pdf
Autocad 2013 DXF: WBIO-DO-SSR-8.dxf.zip
Autocad PDF: WBIO-DO-SSR-8.pdf