Input-output modules
Input and output modules are stacked together with the Wiren Board controller through the connector on the right side of the enclosure.
You can connect up to 8 modules: Up to 4 input modules (type I), and up to 4 output module (Type O and IO). Exception: only one WBIO-AI-DV-12 module can be connected. The module type determines the module address on the side connector bus of the controller.
Addresses are distributed in the order of connection. Up to 4 modules can be connected in any order. With a larger number, you should daisy-chain connect modules of one type first, then of another type.
Communication Interface - I2C.
Article | Description | Number of channels | Channel type | Width, DIN units rail | Type |
---|---|---|---|---|---|
Input modules | |||||
WBIO-DI-DR-8 | digital dry contact inputs module | 8 | digital dry contact inputs | 2U | I |
WBIO-DI-DR-16 | digital dry contact inputs module | 16 | digital dry contact inputs | 3U | I |
WBIO-DI-DR-14 | digital dry contact inputs module | 14 | digital dry contact inputs | 2U | I |
WBIO-DI-WD-14 | universal digital dry contact inputs module | 14 | digital dry contact inputs
low voltage presence inputs |
2U | I |
WBIO-DI-HVD-8 | Модуль-детектор наличия сетевого напряжения (230В) | 8 | входы напряжения 50-250В AC | 2U | I |
WBIO-DI-HVD-16 | Модуль-детектор наличия сетевого напряжения (230В) | 16 | входы напряжения 50-250В AC | 3U | I |
WBIO-DI-LVD-8 | Модуль-детектор наличия напряжения 12/24В | 8 | входы напряжения 9-50В AC/DC | 2U | I |
WBIO-DI-LVD-16 | Модуль-детектор наличия напряжения 12/24В | 16 | входы напряжения 9-50В AC/DC | 3U | I |
WBIO-AI-DV-12 | Модуль аналоговых входов | 12 (6 дифф.) | аналоговые входы 0-3V,-50..+50V | 3U | I |
WBIO-AI-DV-12/4-20MA | Модуль аналоговых входов 4-20мА | 12 | аналоговые входы 4-20мА | 3U | I |
Модули выходов | |||||
WBIO-DO-R3A-8 | Модуль релейных выходов 3A | 8 | механические реле, SPST и SPDT | 3U | O |
WBIO-DO-R10A-8 | Модуль релейных выходов 10A | 8 | механические реле, SPST | 3U | O |
WBIO-DO-R10R-4 | Модуль релейных выходов 10A
Main article: WBMZ-DIO-TTL-16. Activating the modules in the controller web interfaceTo activate a new module connected to the controller, go to the Hardware Modules Configuration section. Select the module position in the List of extension slots(for example, the first position: External I/O module 1). Select the type in the Module type list. Click the Save button at the top of the page and make sure that the external module is visible in the web interface: MQTT-topics of the new module: /devices/wb-gpio/controls/EXT1_K1 — /devices/wb-gpio/controls/EXT1_K8 |