Wiren Board NETMON-1
Wiren Board NETMON-1 is a universal controller for automation with open software based on Linux, a built-in GSM modem and designed in a case for installation in a 19" rack.
Designed for monitoring of network and telecommunication equipment, polling of sensors and counters, remote power management.
thumb|400px|Wiren Board NETMON-1
Technical specifications
Software | |
---|---|
Operating System | Debian Linux 7.0. Mainline kernel 3.19. |
Controller | |
CPU | Freescale i.MX233 454 MHz |
RAM | DDR SDRAM 64 MB |
ROM | MicroSD card 32 GB max |
"'Wireless interfaces'" | |
Wi-Fi | 802.11 b/g/n 2.4 GHz (optional, installed in the USB connector inside the device) |
GSM/GPRS | 900 / 1800MHz. GPRS multi-slot class 10/8 max. 85.6 kbps (downlink). MiniSIM card (full size) |
"'Wired interfaces'" | |
Ethernet | 10/100 Mbps, RJ-45 |
USB 2.0 Host | (inside case) |
2xRS-485 | software support for Modbus RTU, ADICON/A-BUS/Uniel, Smartbus G4 protocols |
2xRS-232 | one port on the front, one on the back. |
Debug console | Debug UART connects via USB-UART adapter |
1-Wire | Connecting temperature, humidity sensors |
Connect sensors | |
8x ADC | up to 20V |
22xDry contact | Connection of buttons, reed switches, counters with pulse outputs. |
Outputs | |
2hrele | 220V/10A, normally closed. Pairs IEC-320-C13 socket - IEC-320-C14 plug on the rear panel. |
4hRelay | 220V/6A, switching group of contacts. Displayed on the front panel terminals. |
"other" | |
Buzzer | beeper. |
Real time clock | RTC battery Backup |
Watchdog timer | Separate hardware watchdog, restarting the device entirely by power supply |
Temperature and humidity sensor | built-In sensor sht10 inside the case |
"food" | |
Power consumption | <5 W (peak - up to 12 W) |
Battery backup | built-in li-ion battery (option: 1800mAh or 3600mAh) |
twisted pair power | Passive Power over Ethernet |
Overall dimensions | 431 x 203 x 43 mm , 19" rack mount housing, 1U |
Operation | operating temperature - 0..70C (-40..85C on request) Varnish for moisture protection. |
Package
- Wiren Board NETMON-1 controller
- memory card with Linux OS
- 4pcs counter terminals
- 19" rack mount housing kit
Preparation for work
- Remove the top cover of the housing
- Install the power button connector into the connector
- Insert a SIM card if required
- Install rack mounts
- Install the top cover of the housing, tighten the screws included in the kit
Power Supply
External power supply
The permissible power range is 5-22V. The average consumption of the device is 1.5-2 watts. But since the GSM module consumes up to 8W impulsively, it is recommended to use power supplies with a power of at least 10W.
Power plug for standard jack 5.5x2.1 mm located on the rear panel. Power can also be supplied to the corresponding pins (see Pinout below) of the RJ45 connector on the rear panel.
Power over Ethernet
Supports Power over Ethernet (Passive PoE) via RJ45 connector on the front panel. Supports the standard voltage of 12V and 15V. See Power over Ethernet.
Battery
The Wiren Board NETMON-1 can be equipped with one or two Li-Ion (Li-Pol) batteries with a maximum voltage of 4.2 V. When the power is connected, the battery is charged with a current of up to 0.5 A.
Protection against charging at low temperatures and overheating.
GSM/GPRS-modem
Wiren Board NETMON-1 comes with 2G (GPRS) modem that supports GPRS, CSD, sending and receiving SMS.
The GSM antenna is connected to the SMA connector on the back of the controller. If the GSM signal is weak, it is recommended to use a remote antenna and place it away from the controller.
USB port
Wiren Board NETMON-1 has one USB port (Host, type A) inside the case. The port is designed to connect Wi-Fi sticks, 3G modems, etc.
External load switching
Back panel
thumb | 500px | Inputs/outputs for 220V control and GSM antenna connector
The Wiren Board NETMON-1 is equipped with two power switching groups on the rear panel.
Each group consists of an IEC-320-C14 plug (input) and an IEC-320-C13 socket (output). The input and output are connected via a relay. The relay is normally closed (i.e. when WB NETMON-1 is off, the sockets are on).
Rated relay current: 16A/250VAC. The relay opens only one (phase) wire. It is recommended to use outputs for switching resistive load up to 10A.
On request, a configuration is available to use a common input to both outputs.
Передняя панель
thumb | 300px | Релейный выходы на передней панели
На передней панели Wiren Board NETMON-1 находятся четыре группы релейных выходов, выведенные на разъёмные клеммники.
Каждое реле является переключаемым, т.е. выведены контакты NO (нормально-разомкнутый), NC (нормально-замкнутый), COM (общий).
Номинальный ток реле: 10А@240VAC (резистивной нагрузки).
Рекомендуется использовать выходы для коммутации резистивной нагрузки до 5А @ 240В переменного тока.
Последовательные порты
Wiren Board NETMON-1 оснащён двумя полудуплексными портами RS-485 и двумя портами RS-232 (только RX/TX).
Оба порта RS-485 и один порт RS-232 выведены на разъёмы RJ45 на передней панели, один порт RS-232 выведен на разъём RJ45 на задней панели.
Устройства в Linux:
- /dev/ttyNSC0 - RS-485 на разъёме и8
- /dev/ttyNSC1 - RS-485 на разъёме и6
- /dev/ttyNSC2 - RS-232 на разъёме и4
- /dev/ttyNSC3 - RS-232 на разъёме на задней панели
Про работу с RS-485 и подключениие периферийных устройств см. также статью RS-485.
Отладочная консоль
Отладочная консоль (debug UART) выведена на разъём и2 (см. ниже), а также на гребёнку внутри корпуса. Порт имеет уровни 3.3V и требует специального переходника USB-UART или RS232-UART для подключения к компьютеру.
Подробности по работе с отладочной консолью см. в статье Debug UART.
Разъёмы передней панели
thumb|700px| передняя панель thumb|700px|
thumb|300px|схема передней панели
порты | функция |
и1 | discrete input |
и2 | 1-wire / Debug UART |
и3 | discrete input |
и4 | RS-232 |
и5 | discrete input |
и6 | RS-485 |
и7 | discrete input |
и8 | RS-485 |
и9 | discrete input |
а1 | ADC input |
а2 | ADC input |
а3 | ADC input |
а4 | ADC input |
а5 | ADC input |
а6 | ADC input |
а7 | ADC input |
Ehternet | и1 | и2 | и3 | и4 | и5 | и6 | и7 | и8 | и9 |
1 Y/W | discrete input 1 | 5v | discrete input 6 | - | Isolated GND | - | Isolated GND | - | Isolated GND |
2 Y | discrete input 2 | 5v | discrete input 7 | - | discrete input 11 | - | discrete input 15 | - | discrete input 19 |
3 G/W | discrete input 3 | Debug Tx | discrete input 8 | GND | Isolated GND | - | Isolated GND | - | Isolated GND |
4 B | discrete input 4 | 1-Wire | discrete input 9 | RS-232 Tx 1 | discrete input 12 | RS-485 A2 | discrete input 16 | RS-485 A1 | discrete input 20 |
5 B/W | discrete input 5 | GND | discrete input 10 | GND | Isolated GND | RS-485 B2 | Isolated GND | RS-485 B1 | Isolated GND |
6 G | Isolated GND | Debug Rx | Isolated GND | RS-232 Tx 1 | discrete input 13 | GND | discrete input 17 | GND | discrete input 21 |
7 Br/W | Isolated GND | GND | Isolated GND | - | Isolated GND | - | Isolated GND | - | Isolated GND |
8 Br | Isolated GND | GND | Isolated GND | - | discrete input 14 | - | discrete input 18 | - | discrete input 22 |
Ethernet | а1 | а2 | а3 | а4 | а5 | а6 | а7 |
1 Y/W | 3.3V | - | - | - | - | - | - |
2 Y | 3.3V | - | - | - | - | - | - |
3 G/W | GND | - | - | - | - | - | - |
4 B | ADC input 4 | ADC input 1 | ADC input 6 | ADC input 2 | ADC input 7 | ADC input 3 | ADC input 8 |
5 B/W | GND | GND | GND | GND | GND | GND | GND |
6 G | ADC input 5 | - | - | - | - | - | - |
7 Br/W | 5V | - | - | - | - | - | - |
8 Br | 5V | - | - | - | - | - | - |
Задняя панель
thumb|300px|Распиновка разъёма RJ-45 на задней панели WB NETMON-1
Разъём RJ-45 на задней панели, распиновка:
Ethernet | |
1 Y/W | RS-232 TX (2) |
2 Y | RS-232 TX (2) |
3 G/W | RS-232 RX (2) |
4 B | V+ вход (5-15V) |
5 B/W | V+ вход (5-15V) |
6 G | RS-232 RX (2) |
7 Br/W | GND |
8 Br | GND |
shield | GND |
Список GPIO
Wiren Board NETMON-1: Список GPIO
Стандартные схемы подключения
thumb|400px|Пример подключения кнопки
Управление низковольтной нагрузкой
Реле на 12/24В, светодиоды, вентиляторы, сигнальные лампы и т. д.
Низковольтной нагрузкой можно управлять с помощью четырёх реле на передней панели.
Контакторы с управляющим напряжением 220В
Подключите управляющую катушку контактора через реле на передней панели.
Реле в Wiren Board NETMON-1 не содержит защитных демпфирующих цепочек, соблюдайте осторожность при подключении индуктивной нагрузки.
Датчики с аналоговым выходом по напряжению
Подключите землю устройства к клемме GND, или соедините с общей земляной шиной. Выход датчика подключается к аналоговым входам в разъёмах а1-а7.
Датчики с аналоговым токовым выходом
Специальных токовых входов в Wiren Board NETMON-1 нет, но можно, используя резистор 100-300Ом, ток преобразовать в напряжение и подключить как в предыдущем пункте.
Датчики с резистивным выходом
С помощью внешнего резистора и опорного напряжения нужно собрать делитель, чтобы получить выход напряжения (см. предыдущие пункты). В качестве опорного напряжения можно использовать выход +5V с контактов 7-8 разъёма а1, или 1-2 разъёма и2.
Датчики удобно подключать к разъёму "а1", имеющему два входа АЦП и опорные напряжения .
Аналоговые датчики с внешним питанием
Аналоговые датчики с внешним питанием, такие как электрохимические датчики серии MQ-xxx, датчики влажности HIH-4000 и т.д. также удобно подключать к разъёму "а1", имеющему входы АЦП и опорные напряжения.
Датчики/счетчики с импульсными выходами
Такие устройства формируют сигнал, замыкая подходящие к ним два провода. Подключите один провод к контакту "Isolated GND". Второй провод подключите к одному из соответствующему контакту (discrete input) разъёмов и1,и3,и5,и7,и9.
Некоторые счетчики имеют импульсный выход на оптроне, тогда два провода имеют полярность - "плюс" и "минус". В таком случае минус подключается к "Isolated GND", "плюс" к "discrete input".
Подключение к 1-Wire сети
Для подключения 1-wire используется разъём и2.
Землю сети подключите к контактам GND (7-8@и2 и др.) или общей земляной шине. Линию данных к контакту "1-Wire" ( 4@и2) . Линию питания к контакту "5V" (1-2@и2) (внутренний источник питания). Допускается использовать внешние источники питания шины 1-Wire.
При использовании пассивного питания, контакт питания каждого датчика соединяется с земляным проводом. В этом случае, шина прокладывается двумя проводами, подключаемыми соответственно к "1-Wire" и "GND".
Подключение к сети RS-485
Смотрите RS-485.
В Wiren Board NETMON-1 два порта RS-485 на разъёмах "и6" и "и8".
Линии А В подключаются к клеммам А и В соответственно.
Датчик температуры и влажности
Wiren Board NETMON-1 может комплектоваться встроенным датчиком температуры и влажности. Подробнее см. Датчик SHT1x.