Модули расширения/en: различия между версиями
Fizikdaos (обсуждение | вклад) (Новая страница: «* RS-232 Extansion module * Wiren Board 5: Модуль расширения CAN-ISO | CAN (Isolat…») |
Fizikdaos (обсуждение | вклад) |
||
| Строка 14: | Строка 14: | ||
See relevant articles to describe the connection and operation in the software: | See relevant articles to describe the connection and operation in the software: | ||
* [[Wiren Board 5: Модуль расширения RS-232 | RS-232 Extansion module]] | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения RS-232 | RS-232 Extansion module]] | ||
* [[Wiren Board 5: Модуль расширения CAN-ISO | CAN (Isolated) Extansion module]] | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения CAN-ISO | CAN (Isolated) Extansion module]] | ||
* [[Wiren Board 5: Модуль расширения RS485-ISO | RS-485 (Isolated) Extansion module]] | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения RS485-ISO | RS-485 (Isolated) Extansion module]] | ||
* [[Wiren Board 5: Модуль расширения ADC | ADC Extansion module]] - (in developing) voltage inputs, inputs 0-20mA, PT100 and PT1000 sensors | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения ADC | ADC Extansion module]] - (in developing) voltage inputs, inputs 0-20mA, PT100 and PT1000 sensors | ||
* [[Wiren Board 5: Модуль расширения DAC | DAC Extansion module]] - (in developing) 0-10V outputs | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения DAC | DAC Extansion module]] - (in developing) 0-10V outputs | ||
* [[Wiren Board 5: Модуль расширения DI | Module for inputs "dry contact"]] | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения DI | Module for inputs "dry contact"]] | ||
* [[Wiren Board 5: Модуль расширения GPS/Glonass | GPS/Glonass Extansion module]] | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения GPS/Glonass | GPS/Glonass Extansion module]] | ||
* [[Wiren Board 5: Модуль расширения 1-Wire | 1-Wire Extansion module]] | * [[Special:MyLanguage/Wiren Board 5: Модуль расширения 1-Wire | 1-Wire Extansion module]] | ||
Версия 16:39, 14 января 2016
This article describes the expansion modules to the controller Wiren Board 5.
Wiren Board 5 have two slots for expansion modules.
To install the expansion module, the controller Wiren Board 5 in the case for DIN-rail is necessary to disassemble: remove the back cover and extract PCB. When connecting module observe polarity module connector.
When ordering extension modules in set with the controller Wiren Board 5, expansion modules are installed by the manufacturer.
See relevant articles to describe the connection and operation in the software:
- RS-232 Extansion module
- CAN (Isolated) Extansion module
- RS-485 (Isolated) Extansion module
- ADC Extansion module - (in developing) voltage inputs, inputs 0-20mA, PT100 and PT1000 sensors
- DAC Extansion module - (in developing) 0-10V outputs
- Module for inputs "dry contact"
- GPS/Glonass Extansion module
- 1-Wire Extansion module