Перейти к содержанию

Навигация

Firmware Changelog: различия между версиями

Firmware Changelog (просмотреть исходный код)

Версия 18:40, 11 февраля 2021

4275 байт добавлено ,  3 года назад
→‎Общая таблица по всем устройствам/ Summary table for all devices
(не показано 19 промежуточных версий 4 участников)
Строка 1: Строка 1:
{{DISPLAYTITLE:Журнал изменений прошивок}}
== Updating firmware ==
== Updating firmware ==
Please see [[WB-MCU-Flasher | this page]] for details.
Please see [[WB-MCU-Flasher | this page]] for details.
Строка 16: Строка 18:
|
|
|
|
|-
|WB-MS
|08-02-2021
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.5/ 4.16.5]
|WB-MSW v.3, WB-MS v.2, WB-MIR, WB-M1W2, WB-MAI2mini
|
* Fixed uart freezing on a noizy line with ongoing communication at 115200 baud rate.
|-
|WB-MS
|04-02-2021
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.4/ 4.16.4]
|WB-MSW v.3
|
* Add SPL calibration data for MEMS mic.
|-
|WB-MS
|01-02-2021
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.3/ 4.16.3]
|WB-MSW v.3
|
* New MSW model target with only  hdc1080 sensor and buzzer.
|-
|WB-MR
|24-12-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MR/stable/1.15.2/ 1.15.2]
|all
|fix safety timer (problem in 1.15.0, 1.15.1)
|-
|WB-MS
|21-12-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.2/ 4.16.2]
|WB-MSW v.3, WB-MS v.2, WB-MIR, WB-M1W2, WB-MAI2mini
|
* Fixed unstable modbus communication under wb-mqtt-serial fast polling condition.
|-
|WB-MD
|04-12-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MD/stable/2.2.1/ 2.2.1]
|WB-MDM3
|
* Fix zero cross time, considers FET close time.
|-
|WB-MCM
|02-12-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MCM/stable/1.2.0/ 1.2.0]
|WB-MCM8
|
* Add inputs debounce parameters. The default value is 50 ms, which can be changed by Modbus master, saved in EEPROM.
* Add inputs frequency calculation.
|-
|WB-MS
|20-11-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.1/ 4.16.1]
|WB-MSW v.3
|
* Add dynamic temperature compensation for devices with onboard CO2 sensor. Substructed factory hardcoded temperature compensation parameter. Now temperature compensation is applied only when CO2 sensor is operating and 245 register is left for user temperature adjustments
* Fix illuminance sensor work at high illumination conditions
|-
|WB-MS
|23-10-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.0/ 4.16.0]
|WB-MSW v.3, WB-MS v.2, WB-MIR, WB-M1W2, WB-MAI2mini
|
* Add MCU internal voltage and temperature registers
* Add minimum input voltage register
* Fix unstable modbus communication on 115200 baudrate
* Fix unstable co2 sensor communication
* Fix m1w2 unstable digital input mode
|-
|WB-MAP
|10-10-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MAP/stable/2.2.7/ 2.2.7]
|MAP6SE, MAP3E, MAP12E
|
* Target for MAP6SE.
* Delete not existed regs in E devices.
|-
|WB-MS
|07-10-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.15.1/ 4.15.1]
|WB-MSW v.3
|
* affect: WB-MSW v.3 rev 4.9
* note: Improved SPL accuracy for low dB range for some sensors.
* note: Report measurements outside well-defined response curves. The total range of reported values is 37.4-115 dBA   
|-
|WB-MS
|28-09-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.15.0/ 4.15.0]
|ALL
|
* Improve input voltage measure and powerdown handle
* Increase software I2C speed to 50 kHz for faster EEPROM writing
* Fixed modbus frame borders detection
* Added holding register 113 to set modbus inter frame timeout
* Rework hdc1080, opt3001, sgpc3 modules with new non blocking i2c library
* Added MSW v3 rev 4.9 target with mems mic and additional highgain adc input channel
* Removed SPL linear approximation calculation. All targets use response tables
* Changed digital input counter saving to EEPROM algorithm for devices with digital inputs. Previously counters data was loaded to EEPROM once per 600 sec. Now if counter increments slower than 1 time per 300s, the data uploads in EEPROM for each change, otherwise, not faster than 1 time per 300s.
|-
|WB-MS
|14-09-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.14.1/ 4.14.1]
|ALL
|Reduce 1wire sensors initialization time.
|-
|WB-MR
|02-09-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MR/stable/1.15.1/ 1.15.1]
|WB-MIR WB-M1W2 WB-MSv2
|Improve input voltage measure and powerdown handle.
|-
|WB-MS
|31-08-2020
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.14.0/ 4.14.0]
|ALL
|Rework all sensors with task manager module
|-
|-
|WB-MR
|WB-MR
NikitaGorbadey
100

правок

Источник — https://wirenboard.com/wiki/Служебная:Сравнение_версий/41985...45479