100
правок
Firmware Changelog: различия между версиями
→Общая таблица по всем устройствам/ Summary table for all devices
N.kulikov (обсуждение | вклад) |
|||
| (не показано 14 промежуточных версий 3 участников) | |||
| Строка 1: | Строка 1: | ||
{{DISPLAYTITLE:Журнал изменений прошивок}} | |||
== Updating firmware == | == Updating firmware == | ||
Please see [[WB-MCU-Flasher | this page]] for details. | Please see [[WB-MCU-Flasher | this page]] for details. | ||
| Строка 16: | Строка 18: | ||
| | | | ||
| | | | ||
|- | |||
|WB-MS | |||
|08-02-2021 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.5/ 4.16.5] | |||
|WB-MSW v.3, WB-MS v.2, WB-MIR, WB-M1W2, WB-MAI2mini | |||
| | |||
* Fixed uart freezing on a noizy line with ongoing communication at 115200 baud rate. | |||
|- | |||
|WB-MS | |||
|04-02-2021 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.4/ 4.16.4] | |||
|WB-MSW v.3 | |||
| | |||
* Add SPL calibration data for MEMS mic. | |||
|- | |||
|WB-MS | |||
|01-02-2021 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.3/ 4.16.3] | |||
|WB-MSW v.3 | |||
| | |||
* New MSW model target with only hdc1080 sensor and buzzer. | |||
|- | |||
|WB-MR | |||
|24-12-2020 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MR/stable/1.15.2/ 1.15.2] | |||
|all | |||
|fix safety timer (problem in 1.15.0, 1.15.1) | |||
|- | |||
|WB-MS | |||
|21-12-2020 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.2/ 4.16.2] | |||
|WB-MSW v.3, WB-MS v.2, WB-MIR, WB-M1W2, WB-MAI2mini | |||
| | |||
* Fixed unstable modbus communication under wb-mqtt-serial fast polling condition. | |||
|- | |||
|WB-MD | |||
|04-12-2020 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MD/stable/2.2.1/ 2.2.1] | |||
|WB-MDM3 | |||
| | |||
* Fix zero cross time, considers FET close time. | |||
|- | |||
|WB-MCM | |||
|02-12-2020 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MCM/stable/1.2.0/ 1.2.0] | |||
|WB-MCM8 | |||
| | |||
* Add inputs debounce parameters. The default value is 50 ms, which can be changed by Modbus master, saved in EEPROM. | |||
* Add inputs frequency calculation. | |||
|- | |||
|WB-MS | |||
|20-11-2020 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.1/ 4.16.1] | |||
|WB-MSW v.3 | |||
| | |||
* Add dynamic temperature compensation for devices with onboard CO2 sensor. Substructed factory hardcoded temperature compensation parameter. Now temperature compensation is applied only when CO2 sensor is operating and 245 register is left for user temperature adjustments | |||
* Fix illuminance sensor work at high illumination conditions | |||
|- | |||
|WB-MS | |||
|23-10-2020 | |||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MS/stable/4.16.0/ 4.16.0] | |||
|WB-MSW v.3, WB-MS v.2, WB-MIR, WB-M1W2, WB-MAI2mini | |||
| | |||
* Add MCU internal voltage and temperature registers | |||
* Add minimum input voltage register | |||
* Fix unstable modbus communication on 115200 baudrate | |||
* Fix unstable co2 sensor communication | |||
* Fix m1w2 unstable digital input mode | |||
|- | |- | ||
|WB-MAP | |WB-MAP | ||
|10-10-2020 | |10-10-2020 | ||
|2.2.7 | |[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MAP/stable/2.2.7/ 2.2.7] | ||
|MAP6SE, MAP3E, MAP12E | |MAP6SE, MAP3E, MAP12E | ||
| | | | ||