История
9 июня 2020
19 июля 2019
Нет описания правки
−40
Нет описания правки
−18
Нет описания правки
+57
Нет описания правки
Нет описания правки
+3
Новая страница: «As a result of the command, we receive string '''WBMIR'''. The WB-MIR module in the example has Modbus address 1.»
−85
Новая страница: «=== Register reading example === Let's check whether it is true that we are connected to the module of the desired type. (Module wb-mqtt-serial needs to be stoppe…»
−254
Новая страница: «== Command-line device management == The Wiren Board controller software includes modbus_client utility to work with devices connected to the RS-485 outputs, via…»
−217
Новая страница: «In the latest firmware versions, the value of number_of_banks is 80, that is, for example, command size registers have values from 5400 to 5479.»
−92
Новая страница: «{| border="1" class="wikitable" style="text-align:center" !Starting address || Type || Quantity || Purpose || In modifications |- | 5000 || coil|| 1 || style="tex…»
−421
Новая страница: «=== Map registers, flags, and inputs (Inputs and Coils) ===»
−25
Новая страница: «{| border="1" class="wikitable" style="text-align:center" !Register/ address !type !read-write !default !format !appointment |- |6 |input |R |0x7FFF — sensor no…»
−689
Новая страница: «===Holding Registers===»
−50
Новая страница: «== Register map ==»
−17
Новая страница: «=== Removing all signals from permanent memory === To delete all recorded signals, write 1 to the flag register at <code>5000</code>.»
−113
Новая страница: «As in the case of registers of the permanent storage every time you can only perform one operation only one signal. Since during the execution of any operation on…»
−467
Новая страница: «The control of the IR receiver is made through the Modbus registers flags (a full list can be found in Coils). There are 3 types of operations with sig…»
−372
Новая страница: «== Operating mode == === Recording the signal to the RAM from the remote control === To write a signal (only one) from the remote control to the RAM without putti…»
−933
Нет описания правки
Новая страница: «=== Removing all signals from ROM === To delete all recorded signals, write 1 to the flag register at <code>5000</code>.»
−128
Новая страница: «==== Playback of a signal from ROM ==== To play back the signal number <code>i</code> from memory, write 1 to the flag register at <code>5100 + i</code>. If the s…»
−1467
Новая страница: «To write the signal number <code>i</code> from the remote control to memory, write 1 to the flag register at <code>5300 + i</code>. Then point the remote control…»
−330
Новая страница: «==== Signal record in ROM with the remote control ==== '''Note:''' For more about work in command line mode, see the section #Control module from the command li…»
−191
Новая страница: «== Constant mode == In constant mode, the IR commands are stored in the device memory and are available after a power reset. Each command is stored in a separate…»
−352
Нет описания правки
+1
Новая страница: «The control of the IR receiver is made through the flags of Modbus registers; a full list can be found in the description of the map registers. There are 3 types…»
−628
Новая страница: «In devices with firmware version "'3.1.0"' and later it is also possible to change the settings of data exchange parameters — see #register Map|Modbus registe…»
−125
Новая страница: «At the physical level, the module is connected via RS-485 interface. Modbus RTU Protocol is used to control the devices. In Wiren Board devices, M…»
−315
Новая страница: «'''Warning!''' Numbers used Modbus registers have changed since firmware version '''3.2.0'''. The instructions stated the new numbers of registers. If you are usi…»
−353
Новая страница: «== Modbus module control ==»
−26
Новая страница: «The latest firmware versions of WB-MIR v.2 and WB-MSW v.3 sequences of commands are compressed by a special algorithm to provide a higher storage density. The seq…»
−222
Новая страница: «In operating mode, the IR signal (only one) is stored in the device's memory. It is recorded there from the control panel when the corresponding Modbus command is…»
−428
Новая страница: «The signal is stored in the device memory as a sequence of natural numbers (each from 0 to 65535), where each number is the duration of the logical 0 or 1 in the…»
−400
Новая страница: «==Method of signal presentation and storage== 400px|thumb|right| The example of the contents of the operational buffer WB-MIR»
−53
Новая страница: «In continuous mode (ROM), the recorded signals are stored in the Flash ROM of the device and stored when the power is turned off. Every time the signal is overwri…»
−193
Новая страница: «The device has two modes of operation: permanent (working with ROM-buffers) and operational (RAM-buffer).»
−64
Новая страница: «The signal from the remote control is recorded by the IR receiver and stored in the device memory, where it can be played on command from the controller or other…»
−342
Новая страница: «'''Warning! All modules (except for WB-MSW v.3) IR control is only possible with short distances (< 1 m).''' == Operating principle ==»
−106
Новая страница: «Instructions for IR transceiver settings for WB-MS, WB-MSW, WB-MIR devices = Purpose = Infrared transceiver, installed in devices WB-MS, WB-MSW modification I a…»
−334
Новая страница: «WB-MSx Consumer IR Manual»
+24 259