wb_editors
14 355
правок
(Новая страница: «Wiren Board 6: Dry contacts module (opto relay)(WBE2-DO-SSR-2)») |
FuzzyBot (обсуждение | вклад) м (FuzzyBot переименовал страницу Wiren Board 6: Модуль выходов "сухой контакт" (оптореле) (WBE2-DO-SSR-2)/en в WBE2-DO-SSR-2 Dry Contact Outputs Extension Module/en без оставления перенаправления: Часть переводимой страницы Wiren Board 6: Модуль выходов "сухой контакт" (оптореле) (WBE2-DO-SSR-2).) |
||
(не показано 11 промежуточных версий 1 участника) | |||
Строка 1: | Строка 1: | ||
</languages> | </languages> | ||
The module is designed to control the inputs of the "dry contact" type in applications where galvanic isolation is required. | |||
== | == Technical specifications == | ||
<div class="tright" style="clear:none">[[Файл:WBE2-DO-SSR-21.png|thumb|200px| | <div class="tright" style="clear:none">[[Файл:WBE2-DO-SSR-21.png|thumb|200px| WBE2-DO-SSR-2 back side]]</div> | ||
<div class="tright" style="clear:none">[[Файл:WBE2-DO-SSR-22.png|thumb|200px| | <div class="tright" style="clear:none">[[Файл:WBE2-DO-SSR-22.png|thumb|200px| WBE2-DO-SSR-2 front side]]</div> | ||
The module contains two SPST (normally open) configuration opto relays with one common contact. | |||
Each channel has built-in protection against voltage surges when switching inductive load (TVS at 40V). | |||
{| class="wikitable" style="text-align:center" | {| class="wikitable" style="text-align:center" | ||
! | !Parameter | ||
! | !Value | ||
|- | |- | ||
| | |Number of outputs | ||
|2 | |2 | ||
|- | |- | ||
| | |Outputs type | ||
| | |opto relay | ||
|- | |- | ||
| | |Contacts configuration | ||
|SPST ( | |SPST (normally open) | ||
|- | |- | ||
| | |Maximum switching voltage | ||
|40V AC/DC | |40V AC/DC | ||
|- | |- | ||
| | |Maximum switching current, per channel | ||
|'''100 mA''' | |'''100 mA''' | ||
|- | |- | ||
| | |The channel resistance in the open state | ||
|< 5 | |< 5 Оhm | ||
|- | |- | ||
| | |Voltage isolation between the controller and the output | ||
| | |1500 Vrms | ||
|- | |- | ||
| | |Maximum power consumption | ||
|0.05 Вт | |0.05 Вт | ||
|- | |- | ||
| | |Compatibility | ||
| | |Compatiblу with [[Wiren Board 6/en]] of all revisions. | ||
|} | |} | ||
== | == Pinout == | ||
<div class="tright" style="clear:none">[[Файл:OPtRel.png|250px|thumb|right| | <div class="tright" style="clear:none">[[Файл:OPtRel.png|250px|thumb|right|Output contact scheme]]</div> | ||
{| class="wikitable" style="text-align:center" | {| class="wikitable" style="text-align:center" | ||
! | !Terminal | ||
! | !Function | ||
|- | |- | ||
|O1 | |O1 | ||
Строка 58: | Строка 58: | ||
== | ==Configuration== | ||
Configuration of the web interface is carried out in the section Configs => Hardware Modules Configuration. | |||
Select ''WBE2-DO-SSR-2: Dual Small Signal SSR Module'' in the Internal slot 1 or 2 section (depending on the slot number) and click Save. | |||
Once added, two additional outputs appear in the Devices next to the controller outputs (the Discrete I/O section). | |||
When adding a device is detected immediately, a reboot is not required. | |||
== MQTT == | == MQTT == | ||
{| class="wikitable" style="text-align:center" | {| class="wikitable" style="text-align:center" | ||
! | !Slot | ||
! | !Terminal | ||
! | !Relay output | ||
! | !Channel (MQTT) | ||
! | !Topic (MQTT) | ||
|- | |- | ||
| rowspan="2" |MOD1 | | rowspan="2" |MOD1 |