WBE2-DO-SSR-2 Dry Contact Outputs Extension Module/en: различия между версиями
(Новая страница: «== Pinout == <div class="tright" style="clear:none">250px|thumb|right|Output contact scheme</div>») |
FuzzyBot (обсуждение | вклад) м (FuzzyBot переименовал страницу Wiren Board 6: Модуль выходов "сухой контакт" (оптореле) (WBE2-DO-SSR-2)/en в WBE2-DO-SSR-2 Dry Contact Outputs Extension Module/en без оставления перенаправления: Часть переводимой страницы Wiren Board 6: Модуль выходов "сухой контакт" (оптореле) (WBE2-DO-SSR-2).) |
||
| (не показано 7 промежуточных версий 1 участника) | |||
| Строка 44: | Строка 44: | ||
{| class="wikitable" style="text-align:center" | {| class="wikitable" style="text-align:center" | ||
! | !Terminal | ||
! | !Function | ||
|- | |- | ||
|O1 | |O1 | ||
| Строка 58: | Строка 58: | ||
== | ==Configuration== | ||
Configuration of the web interface is carried out in the section Configs => Hardware Modules Configuration. | |||
Select ''WBE2-DO-SSR-2: Dual Small Signal SSR Module'' in the Internal slot 1 or 2 section (depending on the slot number) and click Save. | |||
Once added, two additional outputs appear in the Devices next to the controller outputs (the Discrete I/O section). | |||
When adding a device is detected immediately, a reboot is not required. | |||
== MQTT == | == MQTT == | ||
{| class="wikitable" style="text-align:center" | {| class="wikitable" style="text-align:center" | ||
! | !Slot | ||
! | !Terminal | ||
! | !Relay output | ||
! | !Channel (MQTT) | ||
! | !Topic (MQTT) | ||
|- | |- | ||
| rowspan="2" |MOD1 | | rowspan="2" |MOD1 | ||
Текущая версия на 15:46, 22 апреля 2021
</languages> The module is designed to control the inputs of the "dry contact" type in applications where galvanic isolation is required.
Technical specifications
The module contains two SPST (normally open) configuration opto relays with one common contact.
Each channel has built-in protection against voltage surges when switching inductive load (TVS at 40V).
| Parameter | Value |
|---|---|
| Number of outputs | 2 |
| Outputs type | opto relay |
| Contacts configuration | SPST (normally open) |
| Maximum switching voltage | 40V AC/DC |
| Maximum switching current, per channel | 100 mA |
| The channel resistance in the open state | < 5 Оhm |
| Voltage isolation between the controller and the output | 1500 Vrms |
| Maximum power consumption | 0.05 Вт |
| Compatibility | Compatiblу with Wiren Board 6/en of all revisions. |
Pinout
| Terminal | Function |
|---|---|
| O1 | K1 |
| O2 | K2 |
| O3 | COM |
Configuration
Configuration of the web interface is carried out in the section Configs => Hardware Modules Configuration.
Select WBE2-DO-SSR-2: Dual Small Signal SSR Module in the Internal slot 1 or 2 section (depending on the slot number) and click Save.
Once added, two additional outputs appear in the Devices next to the controller outputs (the Discrete I/O section).
When adding a device is detected immediately, a reboot is not required.
MQTT
| Slot | Terminal | Relay output | Channel (MQTT) | Topic (MQTT) |
|---|---|---|---|---|
| MOD1 | O1 | K1 | wb-gpio/MOD1_K1 | /devices/wb-gpio/controls/MOD1_K1 |
| O2 | K2 | wb-gpio/MOD1_K2 | /devices/wb-gpio/controls/MOD1_K2 | |
| MOD2 | O1 | K1 | wb-gpio/MOD2_K1 | /devices/wb-gpio/controls/MOD2_K1 |
| O2 | K2 | wb-gpio/MOD2_K2 | /devices/wb-gpio/controls/MOD2_K2 |