Просмотр кода страницы WBIO-DO-R10R-4 Relay Module For Roller Shutter/en

<languages/>
{{#vardefine:ProductFullName1|roller shutter module WBIO-DO-R10R-4}} {{#vardefine:FileName1|WBIO-DO-R10R-4}} {{#vardefine:ProductName1|WBIO-DO-R10R-4}} 
'''[https://wirenboard.com/en/product/WBIO-DO-R10R-4/ Buy online]'''

[[Файл:WBIO-DO-R10R-4.png|250px|thumb|right| WBIO-DO-R10R-4 ]]

==Purpose==

Control of electric curtains, shutters, shutoff valves.

==Technical specifications==

Contains 4 relay groups.


Each group has three possible states.

{| class="wikitable"
!Parameter
!Value
|-
|Number of output groups
|4
|-
|Output type
|mechanical relay
|-
|Contact configuration
|SPCO/all sptt (see scheme)
output group states: 

* off,

* LX and NC closed,

* Lx and NO closed 
|-
|Maximum switching voltage, AC
|250 V
|-
|Maximum switching voltage, DC
|30 Volts
|-
|Maximum switching current, per channel (*)
|3 A
|-
|The channel resistance in the open state
|< 100 mOhm
|-
|Voltage isolation between the controller and the output
|1500 V (RMS.)
|-
|Lifetime: number of switches

for 10 A 230 V AC load, cos φ = 1
|100 000
|-
|Module type
|"O" (non-inverted address scheme)
|-
|Maximum power consumption
|1 W
|-
|Width, DIN units
|3
|-
|Size
|53,3x90,2x57,5 mm
|}
<nowiki>*</nowiki>) Maximum switching current is specified for 230 VAC resistive load.



{| class="wikitable"
!colspan="2" | '''Terminals and wire section''' 
|-
|| The recommended wire cross section with  pin bushing insulated tip, mm<sup>2</sup>  || 2,5
|-
|| Standard sleeve length of pin bushing insulated tip, mm || 8
|-
||Tightening torque of screws, Н∙м || 0,5
|-
|}

[[File:DIN 3U.png |300px|thumb|right|Dimensions]]

== Connection to the controller ==
== Connection to the controller ==
See [[Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in the web interface of the controller]]. In the Discrete I/O device, EXT(1-8)_DIR(1-4) and EXT(1-8)_ON(1-4) controls will be created after the module connection. DIR controls are responsible for direction selection (relay R2 on the circuit), and ON controls are responsible for switching on and off (relay R1 on the circuit). These controls in MQTT messages are called /devices/wb-gpio/controls/EXT'''x'''_DIR'''y''' and /devices/wb-gpio/controls/EXT'''x'''_ON'''y'''.

[[File:WBIO-DO-R10R-4-controls.png|300px|thumb|right|Module's controls in the web interface]]

== Module outputs — load connection==

The phase wire is connected to the Lx terminals. Both terminals of the Lx contact group are connected on the board. NC and NO terminals are connected to the engine, setting the direction of rotation. The NO and NC outputs are protected by varistors.

[[Файл:Roll.png|400px|thumb|none| Wiring diagram of the engine to the WBIO-DO-R10R-4 module]]

== Images and drawings of the device ==
{{Wbincludes:WBPictures|1}}