wb_editors
14 355
правок
WBIO-DO-R1G-16 1A Relay Module/en: различия между версиями
WBIO-DO-R1G-16 1A Relay Module/en (просмотреть исходный код)
Версия 13:02, 22 апреля 2021
, 3 года назадЧасть переводимой страницы WBIO-DO-R1G-16 I/O Module.
(Новая страница: « Our detailed article in russian on habr.com about the choice of relay parameters for the switched load: https://habr.com/ru/company/wirenboard/blog/422197/») |
FuzzyBot (обсуждение | вклад) (Часть переводимой страницы WBIO-DO-R1G-16 I/O Module.) |
||
| (не показано 12 промежуточных версий 2 участников) | |||
| Строка 19: | Строка 19: | ||
{| class="wikitable" | {| class="wikitable" | ||
! | !Parameter | ||
! | !Value | ||
|- | |- | ||
| | |Number of outputs | ||
|16 | |16 | ||
|- | |- | ||
| | |Number of output groups | ||
|2 | |2 | ||
|- | |- | ||
| | |Output type | ||
| | |mechanical relay | ||
|- | |- | ||
| | |Contact configuration | ||
|SPST, | |SPST, normally open | ||
states: | |||
* | *off. | ||
* | *Kx and NO closed | ||
|- | |- | ||
| | |Maximum switching voltage, alternating current | ||
|250 | |250 V | ||
|- | |- | ||
| | |Maximum switching voltage, direct current | ||
|30 | |30 Volts | ||
|- | |- | ||
| | |Maximum switching current, per channel (*) | ||
|5 | |5 A | ||
|- | |- | ||
| | |Maximum switching current, | ||
the channels in one group | |||
|10 | |10 A | ||
|- | |- | ||
| | |The channel resistance in the open state | ||
|< 50 | |< 50 mW | ||
|- | |- | ||
| | |Voltage isolation between the controller and the output | ||
|2000 | |2000 V (RMS.) | ||
|- | |- | ||
| | |Lifetime: number of switches | ||
for load 3 A 230 V AC, cos φ = 1 | |||
|100 000 | |100 000 | ||
|- | |- | ||
| | |Lifetime: number of switches | ||
for load 0.1 A 230 V AC, cos φ = 1 (**) | |||
|1 000 000 | |1 000 000 | ||
|- | |- | ||
| | |Module type | ||
|"O" (non-inverted address scheme) | |"O" (non-inverted address scheme) | ||
|- | |- | ||
| | |Maximum power consumption | ||
|1 | |1 W | ||
|- | |- | ||
| | |Width, DIN units | ||
|3 | |3 | ||
|- | |- | ||
| | |Size | ||
|53,3x90,2x57,5 | |53,3x90,2x57,5 mm | ||
|} | |} | ||
<nowiki>*</nowiki>) | <nowiki>*</nowiki>) Maximum switching current is specified for 230 VAC resistive load. | ||
<nowiki>**</nowiki>) | <nowiki>**</nowiki>) Calculated value | ||
{| class="wikitable" | {| class="wikitable" | ||
!colspan="2" | ''' | !colspan="2" | '''Terminals and wire section''' | ||
|- | |- | ||
|| | || The recommended wire cross section with pin bushing insulated tip, mm<sup>2</sup> || 2,5 | ||
|- | |- | ||
|| | || Standard sleeve length of pin bushing insulated tip, mm || 8 | ||
|- | |- | ||
|| | ||Tightening torque of screws, Н∙м || 0,5 | ||
|- | |- | ||
|} | |} | ||
[[File:DIN 3U.png |300px|thumb|right| | [[File:DIN 3U.png |300px|thumb|right|Dimensions]] | ||
== | == Connection to the controller == | ||
See [[Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in the web interface of the controller]] | |||
== | == Load connection== | ||
Relays are connected in a phase break. | |||
[[Файл:Relay outputs.png|400px|thumb|none| | [[Файл:Relay outputs.png|400px|thumb|none|Connection scheme]] | ||
== Device pictures and drawings == | |||
== | |||
{{Wbincludes:WBPictures|1}} | {{Wbincludes:WBPictures|1}} | ||