История
4 июня 2019
Новая страница: «When assembling the controller with the module installed, pay attention to the wires of the module: they should not be between the indicator and the plastic light…»
−195
Новая страница: «After installing the module, connect the connectors to the Board, as shown by the arrows in the figure "controller Board with battery and switch connectors": red…»
−174
Новая страница: «The module Board is mounted on two latches (indicated in the figure), the battery down to the side of the Board. The battery should be located on the side of the…»
−271
Новая страница: «300px|thumb|center|Module mounting»
−16
Новая страница: «For the convenience of installing the jumper module in the upper part of the body can be removed (for example, wire cutters).»
−59
Новая страница: «One battery contact is disconnected from the module to prevent discharge during storage. Before installation it is necessary to fix the disconnected contact in a…»
−175
Новая страница: «The WBMZ battery module comes complete with the top cover of the case on which the switch is mounted. The cover is installed instead of the included controller. T…»
−238
Новая страница: «'''Disassemble the controller body according to the instructions .'''»
−15
Новая страница: «300px|thumb|left|Battery module, one battery contact disconnected File:Top_cover_with_switch.png|300px|thumb|right|The top cover of…»
−185
Новая страница: «=Connecting a module purchased separately = <!--полная последовательность действий при установке WBMZ-BATTERY_-_мо…»
−41
Новая страница: «Replace the top cover of the controller. The controller is ready for operation.»
−58
Новая страница: «{| class="wikitable" ! 300px|thumb|left|Initially, the loop connector is not connected to the module ! File:Withbattery2.jpg|300px|th…»
−62
Новая страница: «=Connecting the module that comes with the controller= 300px|thumb|right| Switch on the top cover of the controller If the battery mod…»
−574
Новая страница: «{| class="wikitable" |Type |Li-ion |- |Rated voltage |3,7 В |- |Rated capacity (C) |1800 мАч |- |Maximum charge/discharge |1 C |- |Charging time |0,5 C —…»
−211
Новая страница: «=== Technical characteristics of the LIR103450A batteries ===»
−34
Новая страница: «The standard versions: {| class="wikitable" !Package !Contents !Capacity !Weight |- |WBMZ-BATTERY-1800MAH |Module with LIR103450A-PCB-LD battery |1800 mAh |50 g |…»
−77
Новая страница: «* two sealed - 900 ма.»
+4
Новая страница: «* one sealed - 600 ма.»
−15
Новая страница: «* not soldered - 300 мA.»
−8
Новая страница: «Charging current is set by sealed jumpers:»
−61
Новая страница: «* STAT2 (active low) - the battery is charging.»
−21
Новая страница: «* STAT1 (active low) - the board is connected.»
−9
Новая страница: «The controller receives two signals:»
−21
Новая страница: «The boards are equipped with 1800 mAh batteries.»
−32
Новая страница: «There is no protection against over-discharge of the connected accmulator - be sure to use batteries with built-in protection circuit.»
−105
Новая страница: «The Board contains a charge circuit Li-Ion battery with charge protection at low and high temperatures.»
−80
Новая страница: «Compatible withWiren Board 5 controller. It is connected by a loop to the internal connector of the controller.»
−55
Новая страница: «300px|thumb|right|Top view 300px|thumb|right|Backup power module with LIR103450A battery File:Mezonin.png|500px|thumb|…»
−144
Новая страница: «Additional mezzanine board is installed on the second level in the DIN-rail mounted controller body.»
−55
Новая страница: «WBMZ-BATTERY - backup power module with a Li-Ion battery»
+8665