IO modules/en: различия между версиями

Материал из Wiren Board
(Новая страница: «Ground module must be connected with the ground controller!»)
м (FuzzyBot переименовал страницу I / O modules/en в IO modules/en без оставления перенаправления: Часть переводимой страницы I / O modules.)
 
(не показаны 42 промежуточные версии 4 участников)
Строка 1: Строка 1:
<languages/>
<languages/>
IO modules are joined to the connector on the side WB5.
[[Файл:In-Out1.jpeg|300px|thumb|right| IO module]]
[[Файл:In-Out1.jpeg|300px|thumb|right| IO module]]


[[Файл:In-out.png|300px|thumb|right|Pinout slot for input-output modules]]
Input and output modules  are stacked together with the Wiren Board controller through the connector on the right side of the enclosure.
[[Файл:Connecting_Side_Modules.png|250px|thumb|right| Connecting module to the controller slot]]


You can connect up to 8 modules: Up to 4 input modules (type I), and up to 4 output module (Type O and IO).
[[Файл:In-out.png|300px|thumb|right|The female connector pinout for I/O modules for the controller and the I/O modules]]
WB5 automatically detects connected module and its type.
Addresses are distributed sequentially.
Connect up to 4 modules can be in any order. When a larger number should be connected first one type, then the other.


Communication Interface - I2C.




You can connect up to 8 modules: Up to 4 input modules (type ''I''), and up to 4 output module (Type O and IO).
Exception: only one WBIO-AI-DV-12 module can be connected.
The module type determines the module address on the side connector bus of the controller.


== Digital Input Module type "dry contact" (WBIO-DI-DR-8) ==
Addresses are distributed in the order of connection. Up to 4 modules can be connected in any order. With a larger number, you should daisy-chain connect modules of one type first, then of another type.


[[Файл:WBIO-DI-DR-8-small-crop.jpg|200px|thumb|none|WBIO-DI-DR-8 module]]
Communication Interface - I2C.
 
Contains 8 inputs for connecting "dry contacts" with the group galvanic isolation.
The circuit inputs shown in Fig. On input is applied ~ 4.5V, ground fault current flows small (1mA), triggering input.
 
To input trigger pulse width must be at least 10 ms ???. The time between pulses - 5ms
 
[[Файл:DI.png|300px|thumb|none|Digital inputs DI]]
 
 
== Digital Output Module (WBIO-DO-HS-8) ==
 
[[Файл:WBIO-DO-HS-8-small-crop.jpg|200px|thumb|none|WBIO-DO-HS-8 module]]
 
Contains 8 outputs such as "High Side Switch" - when you turn on channel  Vin voltage is supplied to the output.
 
Designed to control relays, low-voltage motors, etc.
 
Current up to 0,6A per channel. Built-in  overvoltage protection (including load dump), overheat and short circuit protection.
 
Requires external power supply to the terminals '' 'Vin' '' and '' 'GND' ''.
 
Ground module must be connected with the ground controller!
 
Напряжение питания от 11 до 45В.
 
[[Файл:HSx.png|300px|thumb|none|Схема работы модуля High Side Outputs. ]]
 
 
== Модуль релейных выходов (WBIO-DO-R3A-8) ==


[[Файл:WBIO-DO-R3A-8-small-crop.jpg|200px|thumb|none|Модуль WBIO-DO-HS-8]]
{| class="wikitable"
!Article
!Description
!Number of channels
!Channel type
!Width, DIN units rail
!Type
|-
! colspan="5" |'''Input modules'''
!
|-
|WBIO-DI-DR-8
|[[WBIO-DI-DR-8_I/O_Module/en| digital dry contact inputs module]]
|8
|digital dry contact inputs
|2U
|I
|-
|WBIO-DI-DR-16
|[[WBIO-DI-DR-16_I/O_Module/en|digital dry contact inputs module]]
|16
|digital dry contact inputs
|3U
|I
|-
|WBIO-DI-DR-14
|[[WBIO-DI-DR-14 I/O Module/en|digital dry contact inputs module]]
|14
|digital dry contact inputs
|2U
|I
|-


Содержит 8 реле. Два из них перекидные (NO/COM/NC).
|WBIO-DI-WD-14
|[[WBIO-DI-WD-14 I/O Module/en|universal digital dry contact inputs module]]
|14
|digital dry contact inputs
low voltage presence inputs
|2U
|I
|-


Ток до 10А на канал NO-NC (вкл/выкл), до 3A на каналы перекидных реле. Защита от искрения контактов.
|WBIO-DI-HVD-8
|[[Модуль наличия 220В (WBIO-DI-HVD-8)/en| discrete 220V AC voltage presence detection inputs module]]
|8
|220V AC voltage presence detection inputs
|2U
|I
|-
|WBIO-DI-HVD-16
|[[Модуль наличия 220В (WBIO-DI-HVD-16)/en|discrete 220V AC voltage presence detection inputs module]]
|16
|220V AC voltage presence detection inputs
|3U
|I
|-


Номинальный ток указан для резистивной нагрузки 230V переменного тока.


|WBIO-DI-LVD-8
|[[Модуль наличия напряжения (WBIO-DI-LVD-8)/en|Voltage 12/24 V presence detection module]]
|8
|discrete 12/24V presence detection inputs
|2U
|I
|-
|WBIO-DI-LVD-16
|[[Модуль наличия напряжения (WBIO-DI-LVD-16)/en|Voltage 12/24 V presence detection module]]
|16
|discrete 12/24V presence detection inputs
|3U
|I
|-
|WBIO-AI-DV-12
|[[WBIO-AI-DV-12_I/O_Module/en|Analog inputs module ]]
|12 (6 diff.)
|analog inputs 0-3V,-50..+50V
|3U
|I
|-
|WBIO-AI-DV-12/4-20MA
|[[WBIO-AI-DV-12_4-20MA/en|Analog inputs 4-20mА module]]
|12
|Analog inputs 4-20mА
|3U
|I
|-
! colspan="5" |'''Output modules'''
!
|-
|WBIO-DO-R3A-8
|[[Модуль релейных выходов 3A (WBIO-DO-R3A-8)/en|relay outputs 3A module]]
|8
|relay outputs, SPST and SPDT
|3U
|O
|-
|WBIO-DO-R10A-8
|[[WBIO-DO-R10A-8_Relay_Module/en|relay outputs 10A module]]
|8
|relay outputs, SPST
|3U
|O
|-
|WBIO-DO-R10R-4
|[[Модуль релейных выходов 10A (roller shutter) (WBIO-DO-R10R-4)/en| relay outputs (roller shutter) 10A module]]


== Модуль ввода-вывода с TTL-уровнями (WBIO-DIO-TTL-8) ==
[[Модуль релейных выходов 10A (roller shutter) (WBIO-DO-R10R-4)/en|roller shutter module]]
|4
|relay outputs, SPCO
|3U
|O
|-
|WBIO-DO-R1G-16
|[[WBIO-DO-R1G-16 I/O Module/en| 16 channel relay outputs module for managing contactors]]
|16
|relay outputs, SPST
|3U
|O
|-
|WBIO-DO-HS-8
|[[Модуль дискретных выходов (WBIO-DO-HS-8)/en|High Side Switch discrete inputs module]]
|8
|High Side Switch outputs
|2U
|O
|-
|WBIO-DO-SSR-8
|[[Модуль дискретных выходов типа "сухой контакт" (WBIO-DO-SSR-8)/en|Solid State Relay Output Module for managing low voltage loads]]
|8
|solid state relays, SPST, up to 40V
|2U
|O
|-
|WBIO-AO-10V-8
|[[WBIO-AO-10V-8I/O_Module/en|analog outputs module WBIO-AO-10V-8]]
|8
|analog outputs 0 to 10 V
|2U
|O
|-
! colspan="5" |Input-output modules
!
|-
|WBIO-DIO-TTL-8
|[[Модуль ввода-вывода с TTL-уровнями (WBIO-DIO-TTL-8)/en|TTL inputs and outputs module ]]
|
|5V TTL GPIO
|2U
|O
|}


[[Файл:WBIO-DIO-TTL-8-small-crop.jpg|200px|thumb|none|Модуль WBIO-DIO-TTL-8]]
== Activating the modules in the controller web interface ==
Содержит 8 каналов ввода-вывода с уровнями напряжения 5В,каналы по умолчанию настроены как "выход".
[[Файл:Adding_External_Modules.png|800px|thumb|center|Activating the new module]]
Ток до 20 ма. Защита перенапряжений до 60В.


To activate a new module connected to the controller, go to the '''Hardware Modules Configuration''' section. Select the module position in the''' List of extension slots'''(for example, the first position: '''External I/O module 1'''). Select  the type in the '''Module type''' list.


== Мезонинный модуль ввода-вывода с TTL-уровнями (WBMZ-DIO-TTL-16) ==
Click the Save button at the top of the page and make sure that the external module is visible in the web interface:
[[Файл:Activated_External_Module.png|400px|thumb|center|Activated External Module]]


Основная статья: [[Special:MyLanguage/WBMZ-DIO-TTL-16|WBMZ-DIO-TTL-16]].
MQTT-topics of the new module: /devices/wb-gpio/controls/EXT1_K1 — /devices/wb-gpio/controls/EXT1_K8

Текущая версия на 20:32, 20 апреля 2021

Другие языки:
IO module

Input and output modules are stacked together with the Wiren Board controller through the connector on the right side of the enclosure.

Connecting module to the controller slot
The female connector pinout for I/O modules for the controller and the I/O modules


You can connect up to 8 modules: Up to 4 input modules (type I), and up to 4 output module (Type O and IO). Exception: only one WBIO-AI-DV-12 module can be connected. The module type determines the module address on the side connector bus of the controller.

Addresses are distributed in the order of connection. Up to 4 modules can be connected in any order. With a larger number, you should daisy-chain connect modules of one type first, then of another type.

Communication Interface - I2C.

Article Description Number of channels Channel type Width, DIN units rail Type
Input modules
WBIO-DI-DR-8 digital dry contact inputs module 8 digital dry contact inputs 2U I
WBIO-DI-DR-16 digital dry contact inputs module 16 digital dry contact inputs 3U I
WBIO-DI-DR-14 digital dry contact inputs module 14 digital dry contact inputs 2U I
WBIO-DI-WD-14 universal digital dry contact inputs module 14 digital dry contact inputs

low voltage presence inputs

2U I
WBIO-DI-HVD-8 discrete 220V AC voltage presence detection inputs module 8 220V AC voltage presence detection inputs 2U I
WBIO-DI-HVD-16 discrete 220V AC voltage presence detection inputs module 16 220V AC voltage presence detection inputs 3U I
WBIO-DI-LVD-8 Voltage 12/24 V presence detection module 8 discrete 12/24V presence detection inputs 2U I
WBIO-DI-LVD-16 Voltage 12/24 V presence detection module 16 discrete 12/24V presence detection inputs 3U I
WBIO-AI-DV-12 Analog inputs module 12 (6 diff.) analog inputs 0-3V,-50..+50V 3U I
WBIO-AI-DV-12/4-20MA Analog inputs 4-20mА module 12 Analog inputs 4-20mА 3U I
Output modules
WBIO-DO-R3A-8 relay outputs 3A module 8 relay outputs, SPST and SPDT 3U O
WBIO-DO-R10A-8 relay outputs 10A module 8 relay outputs, SPST 3U O
WBIO-DO-R10R-4 relay outputs (roller shutter) 10A module

roller shutter module

4 relay outputs, SPCO 3U O
WBIO-DO-R1G-16 16 channel relay outputs module for managing contactors 16 relay outputs, SPST 3U O
WBIO-DO-HS-8 High Side Switch discrete inputs module 8 High Side Switch outputs 2U O
WBIO-DO-SSR-8 Solid State Relay Output Module for managing low voltage loads 8 solid state relays, SPST, up to 40V 2U O
WBIO-AO-10V-8 analog outputs module WBIO-AO-10V-8 8 analog outputs 0 to 10 V 2U O
Input-output modules
WBIO-DIO-TTL-8 TTL inputs and outputs module 5V TTL GPIO 2U O

Activating the modules in the controller web interface

Activating the new module

To activate a new module connected to the controller, go to the Hardware Modules Configuration section. Select the module position in the List of extension slots(for example, the first position: External I/O module 1). Select the type in the Module type list.

Click the Save button at the top of the page and make sure that the external module is visible in the web interface:

Activated External Module

MQTT-topics of the new module: /devices/wb-gpio/controls/EXT1_K1 — /devices/wb-gpio/controls/EXT1_K8

Источник — https://wirenboard.com/wiki/index.php?title=IO_modules/en&oldid=46324