История
25 июля 2019
Новая страница: «==== Sensors with resistive output ====»
−24
Новая страница: «There are no special current inputs in the Wiren Board NETMON-1, but you can use a resistor 100-300om, convert the current into voltage and connect as in the prev…»
−98
Новая страница: «== Sensors with analog current output ==»
−36
Новая страница: «Connect the ground of the device to the GND terminal, or connect to a common ground bus. The sensor output is connected to analog inputs in A1-A7 connectors.»
−102
Новая страница: «=== Sensors with analog voltage output ===»
−45
Новая страница: «Relay in Wiren Board NETMON-1 contains no protective damping chains, aware when connecting inductive loads.»
−122
Новая страница: «Connect the contactor control coil via the relay on the front panel.»
−67
Новая страница: «=== Electric contactors with control voltage of 220 V ===»
−26
Новая страница: «The low-voltage load can be controlled by four relays on the front panel.»
−80
Новая страница: «12/24V relays, LEDs, fans, signal lights, etc.»
−65
Новая страница: «=== Low voltage load control ===»
−42
Новая страница: «thumb|400px|Button connection example»
−46
Новая страница: «== Standard wiring diagrams ==»
−32
Новая страница: «Wiren Board NETMON-1: List of GPIOs»
−1
Новая страница: «== List of GPIOs ==»
−4
Новая страница: «{|| border="1" class="wikitable" style="text-align:center" |'''Ethernet'''|| |- |1 Y/W|| RS-232 TX (2) |- |2 Y|| RS-232 TX (2) |- |3 G/W|| RS-232 RX (2) |- |4 B|…»
−6
Новая страница: «RJ-45 connector on the rear panel, pinout:»
−30
Новая страница: «thumb|300px|RJ-45 Pinout on the back of WB NETMON-1»
−49
Новая страница: «=== Back panel ===»
−13
Новая страница: «thumb|300px|схема передней панели {|| border="1" class="wikitable" style="text-align:center"…»
−20
Новая страница: «thumb|700px| front panel thumb|700px|»
−30
Новая страница: «=== Front panel relay ===»
−25
Новая страница: «For details on working with the debug console, see Debug UART.»
−69
Новая страница: «Debug console (debug UART) is output to connector I2 (see below), as well as to the comb inside the case. The port has 3.3 V levels and requires a special USB-UAR…»
−143
Новая страница: «== Debug console ==»
−22
Новая страница: «See also RS-485 for information on working with RS-485 and connecting peripherals.»
−73
Новая страница: «Linux devices: * /dev/ttyNSC0 - RS-485 on I8 connector * /dev/ttyNSC1 - RS-485 on I6 connector * /dev/ttyNSC2 - RS-232 on I4 connector * /dev/ttyNSC3 - RS-232 o…»
−67
Новая страница: «Both RS-485 ports and one RS-232 port are output to RJ45 connectors on the front panel, one RS-232 port is output to RJ45 connector on the back panel.»
−75
Новая страница: «The Wiren Board NETMON-1 is equipped with two half-duplex RS-485 ports and two RS-232 ports (RX/TX only).»
−52
Новая страница: «== Serial ports ==»
−31
Новая страница: «* discover * insert button into connector (picture) * insert sim card (picture) * insert sd card (picture) * turn on, check that the green top light is on *…»
−200
Новая страница: «== Preparation for work ==»
−16
Новая страница: «It is recommended to use outputs for switching resistive load up to 5A @ 240V AC.»
−101
Новая страница: «Rated relay current: 10A@240VAC (resistive load).»
−45
Новая страница: «Each relay is switchable, i.e. contacts NO (normally open), NC (normally closed), COM (common) are derived.»
−110
Новая страница: «There are four groups of relay outputs, output on the connector terminals, on the front panel of the Wiren Board NETMON-1.»
−76
Новая страница: « thumb | 300px | Front panel relay outputs»
−43
Новая страница: «=== Front panel ===»
−18
24 июля 2019
Новая страница: «On request, a configuration is available to use a common input to both outputs.»
−66
Новая страница: «Rated relay current: 16A/250VAC. The relay opens only one (phase) wire. It is recommended to use outputs for switching resistive load up to 10A.»
−129
Новая страница: «Each group consists of an IEC-320-C14 plug (input) and an IEC-320-C13 socket (output). The input and output are connected via a relay. The relay is normally close…»
−125
Новая страница: «The Wiren Board NETMON-1 is equipped with two power switching groups on the rear panel.»
−50
Новая страница: « thumb | 500px | Inputs/outputs for 220V control and GSM antenna connector»
−70
Новая страница: «=== Back panel ===»
−15
Новая страница: «== External load switching ==»
−29
Новая страница: «Wiren Board NETMON-1 has one USB port (Host, type A) inside the case. The port is designed to connect Wi-Fi sticks, 3G modems, etc.»
−78
Новая страница: «== USB port==»
−5
Новая страница: «The GSM antenna is connected to the SMA connector on the back of the controller. If the GSM signal is weak, it is recommended to use a remote antenna and place i…»
−126
Новая страница: «Wiren Board NETMON-1 comes with 2G (GPRS) modem that supports GPRS, CSD, sending and receiving SMS.»
−69
Новая страница: «== GSM/GPRS-modem ==»
−5