История
25 июля 2019
Новая страница: « МКА-3 Software»
−11
Новая страница: «Wiren Board Software »
−58
Новая страница: «==Software==»
−39
Новая страница: «Wiren Board NETMON-1 can be equipped with a built-in temperature and humidity sensor. For more information, see SHT1x Sensor.»
−88
Новая страница: «== Temperature and humidity sensor ==»
−26
Новая страница: «Lines A B are connected to terminals A and B respectively.»
−40
Новая страница: «The Wiren Board NETMON-1 has two RS-485 ports on the "I6" and "I8" connectors.»
−8
Новая страница: «See RS-485.»
−29
Новая страница: «=== RS-485 network connection ===»
−17
Новая страница: «When using a passive power supply pin of each sensor is connected to the earth wire. In this case, the bus consists two wires attached, respectively, to '1-Wire "…»
−192
Новая страница: «Connect the ground of the network to the contacts GND (7-8@I2, etc.) or common ground bus. Data line to "1-Wire" contact ( 4@I2). Power line to contact "5V" (1-2@…»
−188
Новая страница: «The 1-wire connection uses the I2 connector.»
−35
Новая страница: «=== Network connection of 1-Wire ===»
−13
Новая страница: «Such devices form a signal by closing two wires that are suitable for them. Connect one wire to the "Isolated GND" pin. Connect the second wire to one of the cor…»
−272
Новая страница: «== Sensors/counters with pulse outputs ==»
−41
Новая страница: «Analog sensors with external power, such as electrochemical sensors series MQ-xxx, humidity sensors HIH-4000, etc. It is also convenient to connect to the connect…»
−141
Новая страница: «=== Analog sensors with external power supply ===»
−30
Новая страница: «The sensors are conveniently connected to the "A1" connector, which has two ADC inputs and reference voltages.»
−46
Новая страница: «Using an external resistor and a reference voltage, the divider must be assembled to obtain a voltage output (see previous paragraphs). As a reference you can use…»
−188
Новая страница: «==== Sensors with resistive output ====»
−24
Новая страница: «There are no special current inputs in the Wiren Board NETMON-1, but you can use a resistor 100-300om, convert the current into voltage and connect as in the prev…»
−98
Новая страница: «== Sensors with analog current output ==»
−36
Новая страница: «Connect the ground of the device to the GND terminal, or connect to a common ground bus. The sensor output is connected to analog inputs in A1-A7 connectors.»
−102
Новая страница: «=== Sensors with analog voltage output ===»
−45
Новая страница: «Relay in Wiren Board NETMON-1 contains no protective damping chains, aware when connecting inductive loads.»
−122
Новая страница: «Connect the contactor control coil via the relay on the front panel.»
−67
Новая страница: «=== Electric contactors with control voltage of 220 V ===»
−26
Новая страница: «The low-voltage load can be controlled by four relays on the front panel.»
−80
Новая страница: «12/24V relays, LEDs, fans, signal lights, etc.»
−65
Новая страница: «=== Low voltage load control ===»
−42
Новая страница: «thumb|400px|Button connection example»
−46
Новая страница: «== Standard wiring diagrams ==»
−32
Новая страница: «Wiren Board NETMON-1: List of GPIOs»
−1
Новая страница: «== List of GPIOs ==»
−4
Новая страница: «{|| border="1" class="wikitable" style="text-align:center" |'''Ethernet'''|| |- |1 Y/W|| RS-232 TX (2) |- |2 Y|| RS-232 TX (2) |- |3 G/W|| RS-232 RX (2) |- |4 B|…»
−6
Новая страница: «RJ-45 connector on the rear panel, pinout:»
−30
Новая страница: «thumb|300px|RJ-45 Pinout on the back of WB NETMON-1»
−49
Новая страница: «=== Back panel ===»
−13
Новая страница: «thumb|300px|схема передней панели {|| border="1" class="wikitable" style="text-align:center"…»
−20
Новая страница: «thumb|700px| front panel thumb|700px|»
−30
Новая страница: «=== Front panel relay ===»
−25
Новая страница: «For details on working with the debug console, see Debug UART.»
−69
Новая страница: «Debug console (debug UART) is output to connector I2 (see below), as well as to the comb inside the case. The port has 3.3 V levels and requires a special USB-UAR…»
−143
Новая страница: «== Debug console ==»
−22
Новая страница: «See also RS-485 for information on working with RS-485 and connecting peripherals.»
−73
Новая страница: «Linux devices: * /dev/ttyNSC0 - RS-485 on I8 connector * /dev/ttyNSC1 - RS-485 on I6 connector * /dev/ttyNSC2 - RS-232 on I4 connector * /dev/ttyNSC3 - RS-232 o…»
−67
Новая страница: «Both RS-485 ports and one RS-232 port are output to RJ45 connectors on the front panel, one RS-232 port is output to RJ45 connector on the back panel.»
−75
Новая страница: «The Wiren Board NETMON-1 is equipped with two half-duplex RS-485 ports and two RS-232 ports (RX/TX only).»
−52
Новая страница: «== Serial ports ==»
−31
Новая страница: «* discover * insert button into connector (picture) * insert sim card (picture) * insert sd card (picture) * turn on, check that the green top light is on *…»
−200