История
4 июня 2019
Новая страница: «=== Battery module === Wiren Board allows you to connect the internal backup power module WBMZ2-BATTERY with Li-Ion (Li-Pol) battery. When the VIN voltage drops b…»
−369
Новая страница: «=== Power over Ethernet === The Power over Ethernet cable is supported. See Power over Ethernet for details. Both connectors support P…»
−256
Новая страница: «Power connector for standard Jack 5.5 x 2.1 mm and also input voltage can be connected To VIN and GND terminals. The power terminal block contains two Vin termina…»
−210
Новая страница: «===External power supply === The permissible power range is 9-36 V (when using the battery module 12 — 36 V), 9 — 48 V in the new revisions; the voltage range…»
−295
Новая страница: «The Wiren Board 6 has four external inputs for connecting of power supplies: DC jack, 2 terminals and Passive PoE. It is possible to simultaneously connect source…»
−133
Новая страница: «== Power Supply == thumb|600px|A block diagram of the Wiren Board 6 power supply »
Новая страница: «Also there are the protective resistors of the offset on the lines, fail safe bias,(stretching of lines A and B) are enabled by default. If the controller is used…»
−166
Новая страница: «== RS-485 line terminators == According to the RS-485 standard, the line must be terminated with 100 — 120 Ohm resistors at both ends. To simplify installation,…»
−192
Новая страница: «'''Attention!''' The input voltage is connected directly to the '''Vout''' terminal: make sure that the devices connected to it are rated for the appropriate volt…»
−123
Новая страница: «== Power supply output Vout == Для питания периферийных устройств можно использовать выход Vout. Он защ…»
+470
Новая страница: «== +5 Vout power output == It is convenient to use +5V output to power the sensors. It is protected from short circuit and high voltage. When the controller is po…»
−257
Новая страница: «Wx can be used to connect discrete sensors. Wx channels are equipped with tightening to +5 V. Dry contact type inputs are connected between ground and Wx. The Wx…»
−193
Новая страница: «See 1-Wire/en.»
−51
Новая страница: «== Wx Inputs == thumb|400px| Wx inputs scheme The main purpose of the WX inputs is to connect external temperature sensors via the 1-Wire b…»
−142
Новая страница: «There is a function of binary input DI for Ax channels - the controller perceives the terminal voltage more than 3 V as a logical unit (input operation), and les…»
−185
Нет описания правки
+6
Новая страница: «For Ax channels, the input stage consists of an ADCx analog-to-digital converter and Rx input impedance (100 kΩ). The ADCx converter has a high input impedance,…»
−506
Новая страница: «The open collector outputs on the Ax channel are displayed in software as Ax_OUT. The path of the channel is: "wb-gpio/Ax_OUT".»
−36
Новая страница: «This type of output is called open collector.»
−45
Новая страница: «*Active: is closed; the channel output is 0. *Inactive: open circuit; high impedance.»
−74
Новая страница: «The output stage consists of a switching Tx element . The Tx key closes the outputs to the ground. Under control of the controller logic schemes , the Tx switch…»
−132
Новая страница: «Universal channels consist of parallel operating input and output stages.»
−86
Новая страница: «== Multifunctional inputs/outputs A1-A4== thumb|400px|Equivalent circuit of A1-A4 channels»
−42
Новая страница: «{{DISPLAYTITLE:Wiren Board 6: Hardware}} thumb|400px|A logical block diagram of the controller Файл:InputsWB6.png|thumb|400px|…»
−195
Новая страница: «Wiren Board 6: Hardware»
+10 253