Wiren Board 6/en: различия между версиями
(Новая страница: «The modem allows you to send and receive SMS, connect to the Internet. Work with two SIM-cards in multiplexing mode. In Wiren Board 6.0 -6.4 controllers. Both con…») |
|||
(не показано 108 промежуточных версий 2 участников) | |||
Строка 37: | Строка 37: | ||
---- | ---- | ||
It is recommended to read the [[Special:MyLanguage/Wiren Board 6:Первое включение/en|'''Getting started''' | It is recommended to read the [[Special:MyLanguage/Wiren Board 6:Первое включение/en|'''Getting started''']] article to start working with the controller. | ||
{{:Программное обеспечение Wiren Board/en}} | {{:Программное обеспечение Wiren Board/en}} | ||
Строка 57: | Строка 57: | ||
[[ | [[WBMZ2-BATTERY/en|'''Backup power module''']] — additional board, installed on the second level(mezzanine) of the WB case on the DIN-rail. Contains Li-Ion (Li-Pol) battery with capacity of 2200 mAh, provides controller operation up to 3 hours. | ||
== Wireless interfaces == | == Wireless interfaces == | ||
Строка 66: | Строка 66: | ||
[[Wi-Fi|''' | [[Wi-Fi/en|''' Wi-Fi ''']] of the Wiren Board can be configured to work in one of three modes: | ||
in hotpoint mode, enabled by default (the name is WirenBoard without password, the address of the controller in the generated network is: 192.168.42.1) | |||
* | * client mode | ||
* | * simultaneous operation in both hotpoint and client modes | ||
[[Bluetooth|''' | [[Bluetooth/en|'''Bluetooth''' 4.0 (Bluetooth Low Energy)]] — you can track the proximity of other Bluetooth devices, such as a mobile phone or Bluetooth tag. | ||
USB | USB stick [[Z-way/en|Z-Wave]] - connects to the USB connector and provides support for Z-Wave devices. | ||
[[433MHz|''' | [[433MHz/en|''' 433 МHz''']] — radio module RFM69H is installed in the controller during production (in versions up to 6.4). Allows you to connect Noolite devices, Oregon sensors to the controller. | ||
In the version of WB6.5 433 Mhz radio module is available as[[Wiren_Board_6:_Модуль_расширения_433MHz_(WBE2S-R-433MHZ)/en|an extension module]]. | |||
Wi-Fi, GSM and 315/433 MHz radio antennas are connected to SMA connectors. | |||
If the GSM signal is weak, it is recommended to use a remote antenna and place it away from the controller. | |||
== | == Wired interfaces == | ||
''' | '''Ethernet''' supports speed up to 10/100 Mbit/s. Wiren Board 6 controller is equipped with two such interfaces. | ||
The controller is equipped with two USB 2.0 (A/F) ports. Both ports operate in USB Host mode; in future versions of the controller, the first port (closest to the Ethernet connector) will support loading the controller firmware. Power control of individual USB devices is described in the article [[Питание USB-портов/en|Power for USB ports]]. | |||
[[File:rs-485-setup-configs.png|thumb|right|300 px| | [[File:rs-485-setup-configs.png|thumb|right|300 px|Configuration is set through the section ''Configs'' [[RS-485:Настройка через веб-интерфейс/en|of the web interface]]]] | ||
[[ | [[RS-485/en|'''RS-485''']] — two-wire bus communication standard. | ||
The controller has 2 RS-485 ports + 2 more ports can be added [[Wiren_Board_6:_Модуль_расширения_RS485-ISO_(WBE2-I-RS485-ISO)/en| by RS-485 extension modules]] . | |||
The [[RS-485:Физическое подключение/en|article ]] will help you to choose and lay the bus cables correctly. | |||
[[RS-485: | [[RS-485:Configuration_via_Web_Interface/en| Configuration]] of the devices is provided in the web interface. | ||
Basically in Wiren Board,[[Драйвер_wb-mqtt-serial/en| driver WB-mqtt-serial ]] works through the system of [[MQTT/en| MQTT]]-messages with connected RS-485 devices. | |||
'''[[CAN]]''' — | '''[[CAN/en| CAN]]''' — is the standard of communication over a two-wire bus. | ||
The controller is multiplexed (output to the same terminals) with a second RS-485 port. | |||
'''[[1-Wire]]''' — | '''[[1-Wire/en | 1-Wire]]''' — is a bus for connecting external sensors on two or three wires. Since this is a bus, you can connect multiple devices to the same 1-Wire port. | ||
The controller software supports connection of DS18B20 type temperature sensors. | |||
It is convenient to use +5V output to power the sensors. | |||
It is protected from short circuit and high voltage supply. When the controller is powered by a battery, the +5V output remains active. | |||
Software control of this output is also supported (it can be disabled). | |||
== | == Universal inputs/outputs A1-A4 == | ||
[[Файл:WB6-kl.png| thumb | 500px| | [[Файл:WB6-kl.png| thumb | 500px| Wiren Board 6 ports and interfaces]] | ||
[[File:Wago.jpeg|thumb|400px| | [[File:Wago.jpeg|thumb|400px|Working with self-locking terminals]] | ||
Universal channel Ah combines three functions and can work as: | |||
* | * [[Управление низковольтной нагрузкой/en|open collector]] output is a key (3A/30V), closing output to the ground | ||
* [[ADC | | * [[ADC/en |ADC]] with a measurement range of 0 — 28 V | ||
* [[ | * [[DI | Digital input ]] — is triggered when the voltage at the terminal is 5 V | ||
== | == W1-W2 channels == | ||
The W1 and W2 channels can work as an interface for connecting [[1-Wire/en| 1-Wire]] sensors (default) or as [[DI/en | digital inputs ]] "dry contact"type. | |||
Note that in the discrete input mode, the trigger occurs when the Wx signal is earthed (GND terminal block), unlike the A1-A4 channels (above). | |||
The mode of each channel is selected independently in the controller configuration. Through the web interface, the desired configuration is located in the section Configs => Hardware Module Configuration => W1 terminal mode. | |||
Multiple DS18B20 temperature sensors can be connected to each channel via a loop: depending on the loop length, the maximum number of sensors is 10 to 20 (the limit is 20 sensors per 5m cable connected by a star). Additional sensors can be connected via the [[Wiren_Board_6:_Модуль_расширения_1-Wire/en|WBE2-I-1-WIRE]] module. | |||
== | == Terminal blocks == | ||
Some terminal blocks can be used to perform more than one function. See the detailed description in the [[Мультиплексирование портов/en| Multiplexing ports ]] article. | |||
{| border="1" width="700" class="wikitable" style="text-align:center" | {| border="1" width="700" class="wikitable" style="text-align:center" | ||
| | | | ||
''' | '''sign''' | ||
| width="20%"| '''Max. V, I''' | | width="20%"| '''Max. V, I''' | ||
| width="10%" | ''' | | width="10%" | '''state''' '''by default''' | ||
| width="60%"|''' | | width="60%"|'''Functions''' | ||
|- | |- | ||
! colspan="4"| | ! colspan="4"| Top row, left block | ||
|- | |- | ||
| '''Vin''' | | '''Vin''' | ||
| 40V (WB6.3,6.4) | | 40V (WB6.3,6.4) | ||
52V (WB6.5) | 52V (WB6.5) | ||
| || | | ||Input voltage, reverse polarity protection | ||
|- | |- | ||
| '''GND''' || || ||" | | '''GND''' || || ||"ground", minus power supply | ||
|- | |- | ||
! colspan="6"| | ! colspan="6"| Top row, right block | ||
|- | |- | ||
| '''O1-O3''' || | || | || | | | '''O1-O3''' || | || | || |Inputs/outputs of the 1st extension module | ||
|- | |- | ||
| '''O1-O3''' || | ||| || | | | '''O1-O3''' || | ||| || |Inputs/outputs of the 2nd extension module | ||
|- | |- | ||
! colspan="8"| | ! colspan="8"| Bottom row, right block | ||
|- | |- | ||
| '''A1-A4''' || 40V , 1A || High Z || [[ | | '''A1-A4''' || 40V , 1A || High Z || [[Управление низковольтной нагрузкой/en|Open collector outputs]], [[ADC/en|ADC]] | ||
|- | |- | ||
| '''GND''' ||| || || | | '''GND''' ||| || || For easy connection of external sensors | ||
|- | |- | ||
| '''W1''' || 40V || 5V || [[ | | '''W1''' || 40V || 5V || [[1-Wire/en|1-Wire]], GPIO | ||
|- | |- | ||
| '''W2''' || 40V || 5V || [[ | | '''W2''' || 40V || 5V || [[1-Wire/en|1-Wire]], GPIO | ||
|- | |- | ||
| '''5V out''' || 5V, 0.5A || 5V || | | '''5V out''' || 5V, 0.5A || 5V ||The 5V output. Shutdown current is exceeded. Software on-off switching. | ||
|- | |- | ||
| '''A''' || 40 V || 0V || rowspan="2"| | | '''A''' || 40 V || 0V || rowspan="2"|port [[RS-485/en|RS-485]] (/dev/RS-485-1) | ||
|- | |- | ||
| '''B''' || 40 V || +5V | | '''B''' || 40 V || +5V | ||
|- | |- | ||
|- | |- | ||
| '''L''' || 40 V || 0V || rowspan="2"| | | '''L''' || 40 V || 0V || rowspan="2"|Port CAN or [[RS-485/en|RS-485]] (/dev/RS-485-2) . | ||
Connecting RS-485: A to terminal '''A|L''', B to terminal '''B|H'''. | |||
|- | |- | ||
| '''H''' || 40 V || +5V | | '''H''' || 40 V || +5V | ||
|- | |- | ||
| '''Vout*''' || 1A || || | | '''Vout*''' || 1A || || Supply output. Input voltage, software on-off switching. | ||
|- | |- | ||
|} | |} | ||
In the 6.3 revision of Wiren Board controller terminals of "type 250" were applied as front-end terminals. | |||
These are self-locking clips. When the cleaned single wire is inserted into the socket, it is automatically clamped with a spring latch. | |||
To insert a stranded conductor, it is necessary to press the spring button clips (or use insulated pin lugs of the bushing isolated pin tips). | |||
The button has a slot for a screwdriver. | |||
To remove the wire, you need to press the spring by pressing the clip button, and pull out the wire. | |||
''' | '''In versions starting from WB6.4''' detachable screw terminals "series 15EDG" with a pitch of 3.5 mm were applied as interface terminals. When screwing, do not make a lot of effort! | ||
== | == Ports and interfaces == | ||
[[ | [[WB_Debug_Console/en | Debug port]] — by connecting to it, you can directly access the controller console. Through it you can also interact with the bootloader and monitor the operating system boot (serial console). | ||
[[Buzzer | " | [[Buzzer/en | "Buzzer"]] — beeps, its frequency is adjustable. | ||
The real-time clock is powered by an internal backup battery. | |||
== | == Watchdog == | ||
The controller contains a separate hardware watchdog that reboots it entirely on power when the software freezes. | |||
[[Hardware_Watchdog_Disable | | [[Hardware_Watchdog_Disable/en | Hardware watchdog disable]] | ||
== | == Power Supply == | ||
The controller has three external inputs for power connection: | |||
* DC jack - | * DC jack - standard plug connector (5.5x2.1mm) on the left side of the case. | ||
* | * VIN and GND terminals: two VIN terminals to which two independent power supplies can be connected for redundancy. The grounds of the power supplies must be connected and connected to the GND terminal. | ||
* | * Power-over-Ethernet (PoE Passive). Read more [[Power over Ethernet/en|Power over Ethernet]]. | ||
It is possible to simultaneously connect the sources to different inputs, including different voltages. | |||
For backup power, you can connect the internal extension module [[WBMZ2-BATTERY/en | WBMZ2-BATTERY ]] with Li-Ion (Li-Pol) battery.'''Important: when the controller is supplied with a battery module, the controller does not turn on immediately when the power is supplied. To turn it on, press the power button of the module under the top cover of the controller. See article [[WBMZ2-BATTERY/en| WBMZ2-BATTERY]].''' | |||
The valid power range is '''9 — 36 V''' for WB rev.6.1 - 6.4.1 , anda '''9 — 48''' for WB6.5. | |||
The average consumption of the Board is 1.5 — 2 watts. But since the GSM module consumes up to 8W impulsively, it is recommended to use power supplies with a power of at least '10W'. | |||
== | == Supported Devices == | ||
[[Периферийные устройства с интерфейсом RS-485 серии WB-xxxx | | [[Периферийные устройства с интерфейсом RS-485 серии WB-xxxx/en |Devices of our production with the RS-485 interface]] | ||
[[ | [[Поддерживаемые устройства/en|Supported devices]] | ||
[[ | [[Wiren Board 5: Подключение периферийных устройств/en|Connection of peripheral devices]] | ||
[[Wires_and_Terminals| | [[Wires_and_Terminals/en|The wiring on the terminal blocks of Wiren Board devices]] | ||
== | == Features of controller network settings == | ||
[[Wirenboard6:InstallingOnTheRemoteSite| | [[Wirenboard6:InstallingOnTheRemoteSite/en|Wiren Board 6: Installing On The Remote Site]] | ||
== | ==Detailed technical description of the controller board== | ||
[[Файл:WB6.4razm.png|thumb|400px| | [[Файл:WB6.4razm.png|thumb|400px|The dimensions of the controller board]] | ||
The article [[Wiren_Board_6:_Hardware/en | Wiren Board 6: Hardware]] describes some of the features of work and the device inputs, the power supply circuit of the controller. | |||
[[ | [[WB_6:_Errata/en | Hardware errors/features of Wiren Board 6 ]] found in the operation of the controller. | ||
[[Wiren Board: Аппаратные ревизии]] — | [[Wiren Board: Аппаратные ревизии/en| Hardware revisions]] — the description of changes in the controller board. | ||
The table of processor and GPIO signals match on the board according to the revisions: [[Wiren_Board_6.0.1:Список_GPIO/en|Wiren Board 6.0.1]], [[Wiren_Board_6.1:Список_GPIO/en|Wiren Board 6.1]], | |||
[[ | [[Wiren_Board_6.2:_Peripherals/en|Wiren Board 6.2 and above]] | ||
[[ | [[Работа с GPIO/en|Working with GPIO]] — how to work directly with GPIO. | ||
[[Обновление прошивки| | [[Обновление прошивки/en|Firmware update]]. To reset the Wiren Board 6 to factory settings (factory reset), use the instructions in the section [[Обновление прошивки/en#The Wiren Board 6 factory reset| The Wiren Board 6 factory reset ]] | ||
[[WB6_root_password_recovery|Wiren Board 6: | [[WB6_root_password_recovery/en|Wiren Board 6: WB6 root password recovery]] | ||
== | == Summary table of characteristics== | ||
{| border="1" width="1000" class="wikitable" style="text-align:center" | {| border="1" width="1000" class="wikitable" style="text-align:center" | ||
!colspan="2" | ''' | !colspan="2" | '''General''' | ||
|- | |- | ||
| | | Processor || [https://www.nxp.com/products/processors-and-microcontrollers/applications-processors/i.mx-applications-processors/i.mx-6-processors/i.mx-6ull-single-core-processor-with-arm-cortex-a7-core:i.MX6ULL NXP i.MX 6ULL] 800 MHz Cortex A7 ( 500MHz and 900MHz upon request) | ||
|- | |- | ||
|| | || RAM || DDR3 SDRAM 512 MB | ||
|- | |- | ||
|| | || Non-volatile memory || 4 GB eMMC | ||
|- | |- | ||
|| | ||Dimensions || DIN railed Enclosure 6Units | ||
106.25x90.2x57.5 | 106.25x90.2x57.5 mm. | ||
Without the case: 103x87x20 mm. | |||
|- | |- | ||
|| | ||Operation || operating temperature 0...+70С/-40..+85С | ||
( | (depending on the configuration). | ||
|- | |- | ||
!colspan="2" | ''' | !colspan="2" | '''Terminals and wire section''' | ||
|- | |- | ||
|| | || The recommended wire cross section with pin bushing insulated tip, mm<sup>2</sup> || 0,75 — 1 | ||
|- | |- | ||
|| | || Standard sleeve length of pin bushing insulated tip, mm || 8 | ||
|- | |- | ||
|| | ||Tightening torque of screws, Н∙м || 0,2 | ||
|- | |- | ||
!colspan="2" | ''' | !colspan="2" | '''Interfaces''' | ||
|- | |- | ||
|| RS-485 || 2 | || RS-485 || 2 | ||
|- | |- | ||
|| CAN || 1 ( | || CAN || 1 (multiplexed with RS-485) | ||
|- | |- | ||
|| | || Wx ports ( 1-Wire/DI) || 2 | ||
|- | |- | ||
|| | || Ax ports (DI / Analog input / open collector output) || 4 | ||
|- | |- | ||
!colspan="2" | ''' | !colspan="2" | '''Communication ports''' | ||
|- | |- | ||
|| Ethernet 10/100 || 2 ( | || Ethernet 10/100 || 2 (with passive PoE) | ||
|- | |- | ||
|| USB Host || 2 | || USB Host || 2 | ||
Строка 321: | Строка 321: | ||
|| Bluetooth 4.0 || 1* | || Bluetooth 4.0 || 1* | ||
|- | |- | ||
|| | || Cellular communication || 2G / 3G / 2G+NB-Iot or without modem * | ||
|- | |- | ||
|| SIM | || SIM cards || 2 x microSIM, simultaneous operation of 2 cards is not supported | ||
|- | |- | ||
!colspan="2" | ''' | !colspan="2" | '''Power''' | ||
|- | |- | ||
|| | || Voltage || 9 - 36V DC | ||
|- | |- | ||
|| | || Power supply circuit || from high voltage input | ||
|- | |- | ||
|| | || Terminal inputs || 2 | ||
|- | |- | ||
|| DC | || DC jack || 1 | ||
|- | |- | ||
|| | || Ethernet power || 1 (1st port) | ||
|- | |- | ||
!colspan="2" | ''' | !colspan="2" | '''Power outputs for external devices''' | ||
|- | |- | ||
|| Vout || | || Vout || input power - with current limit, program shutdown and status monitoring | ||
|- | |- | ||
|| 5Vout || 5V - | || 5Vout || 5V - with current limitation, disabling the software, measure the output voltage | ||
|- | |- | ||
!colspan="2" | '' | !colspan="2" | "'Modularity'" | ||
|- | |- | ||
|| | || Slots for internal extension modules of type WBE2 and WBE2R || 2 | ||
|- | |- | ||
|| | || Slots for internal extension modules such as WBE2S and WBE2R || 1 | ||
|- | |- | ||
|| | || Connector for external input/output modules WBIO || | ||
|- | |- | ||
|| | || Connector for mezzanine power module (battery, supercapacitors, filters) || 1 | ||
|- | |- | ||
!colspan="2" | '' | !colspan="2" | "'Bundled software'" | ||
|- | |- | ||
|| | || Operating system || Linux Debian 9 "Stretch". Mainline kernel 4.9. | ||
|- | |- | ||
|| | || Serial port protocol support || Modbus RTU, mercury, Milur, pulsar, IVTM, etc. | ||
|- | |- | ||
|| | || Protocol support when installing extension modules || Z-Wave, KNX | ||
|- | |- | ||
|| | || Protocol support via IP || KNX IP, Modbus RTU-over-TCP, SNMP | ||
|- | |- | ||
|| | || Built-in Web interface || Adding devices, settings, visualization, mimics | ||
|- | |- | ||
|| | || Scripts || Rules wb-rules in JavaScript, editing via Web-interface. Support for Node-RED scripting | ||
|- | |- | ||
|| | || Visualization || Table view, mimics in the built-in Web-interface. | ||
|- | |- | ||
|| | || Mobile devices || Responsive web interface. Integration with third-party mobile applications: MQTT Dash, iRidium. Supported by the user community: home kit. | ||
|- | |- | ||
|| | || Archive || history storage Module of wb-mqtt-db channels values, up to 1GB of data | ||
|- | |- | ||
|| | || Software update || Individual components via APT, full firmware with backup via Web and USB flash | ||
|- | |- | ||
|| | || Sending data to top-level SOFTWARE || MQTT, Modbus TCP, Zabbix API, etc. | ||
|- | |- | ||
|| | || Top level software support || SAYMON, Zabbix, Nagios, Unimon, Grafana, Master SCADA, Rapid SCADA and others | ||
|- | |- | ||
| | | Other || Easy installation of thousands of packages from Debian, nodejs, python repositories, etc. | ||
Строка 393: | Строка 393: | ||
|} | |} | ||
== | == Images and drawings of the device == | ||
You can download images and drawings of different models of ''Wiren Board 6' controllers via the links below. | |||
{| class="wikitable" | {| class="wikitable" | ||
Строка 407: | Строка 407: | ||
|- | |- | ||
! {{#var:ProductName2}} | ! {{#var:ProductName2}} | ||
| [[Media:{{#var:FileName2}}.cdr.zip|{{#var:FileName2}}.cdr.zip]] || [[Media:{{#var:FileName2}}.cdr.pdf|{{#var:FileName2}}.cdr.pdf]] || | | [[Media:{{#var:FileName2}}.cdr.zip|{{#var:FileName2}}.cdr.zip]] || [[Media:{{#var:FileName2}}.cdr.pdf|{{#var:FileName2}}.cdr.pdf]] || We haven't prepared a drawing for this device yet. You can [https://support.wirenboard.com/new-topic?category=featurerequests/blueprints&title=Чертеж%20устройства%20 send request for the device drawing "{{#var:ProductFullName2}}"] on our support portal (registration required). || — | ||
|- | |- | ||
! {{#var:ProductName3}} | ! {{#var:ProductName3}} | ||
Строка 413: | Строка 413: | ||
|- | |- | ||
! {{#var:ProductName4}} | ! {{#var:ProductName4}} | ||
| [[Media:{{#var:FileName4}}.cdr.zip|{{#var:FileName4}}.cdr.zip]] || [[Media:{{#var:FileName4}}.cdr.pdf|{{#var:FileName4}}.cdr.pdf]] || | | [[Media:{{#var:FileName4}}.cdr.zip|{{#var:FileName4}}.cdr.zip]] || [[Media:{{#var:FileName4}}.cdr.pdf|{{#var:FileName4}}.cdr.pdf]] ||We haven't prepared a drawing for this device yet. You can [https://support.wirenboard.com/new-topic?category=featurerequests/blueprints&title=Чертеж%20устройства%20{{#var:ProductName4}} send request for the device drawing "{{#var:ProductFullName4}}"] on our support portal (registration required).|| — | ||
|- | |- | ||
! {{#var:ProductName5}} | ! {{#var:ProductName5}} | ||
| [[Media:{{#var:FileName5}}.cdr.zip|{{#var:FileName5}}.cdr.zip]] || [[Media:{{#var:FileName5}}.cdr.pdf|{{#var:FileName5}}.cdr.pdf]] || | | [[Media:{{#var:FileName5}}.cdr.zip|{{#var:FileName5}}.cdr.zip]] || [[Media:{{#var:FileName5}}.cdr.pdf|{{#var:FileName5}}.cdr.pdf]] || We haven't prepared a drawing for this device yet. You can [https://support.wirenboard.com/new-topic?category=featurerequests/blueprints&title=Чертеж%20устройства%20{{#var:ProductName5}} send request for the device drawing "{{#var:ProductFullName5}}"] on our support portal (registration required). || — | ||
|- | |- | ||
! {{#var:ProductFullName7}} | ! {{#var:ProductFullName7}} | ||
| — || — || [[Media:{{#var:FileName7}}.dxf.zip|{{#var:FileName7}}.dxf.zip]] || [[Media:{{#var:FileName7}}.pdf|{{#var:FileName7}}.pdf]] | | — || — || [[Media:{{#var:FileName7}}.dxf.zip|{{#var:FileName7}}.dxf.zip]] || [[Media:{{#var:FileName7}}.pdf|{{#var:FileName7}}.pdf]] | ||
|} | |} |
Текущая версия на 14:46, 28 июня 2019
General characteristics
Processor | NXP i.MX 6ULL 800 MHz Cortex A7 ( 500MHz and 900MHz upon request) |
RAM | DDR3 SDRAM 512 MB |
nonvolatile memory | 4 GB eMMC |
Operating system | Debian Linux 9 Stretch. Mainline kernel 4.9. |
Overall dimensions | DIN railed 6U case
106.25x90.2x57.5 mm. Without case: 103x87x20 mm. |
Operation | Operating temperature 0...+70С/-40..+85С
(depending on the configuration). |
Product page and online store: Wiren Board 6
It is recommended to read the Getting started article to start working with the controller.
Программное обеспечение Wiren Board/en
The modularity of the controller
Extension modules — these are small boards installed inside the case of the Wiren Board 6 and extend its functionality: additional ports RS-485, RS-232, relay outputs, etc.
The controller has three slots for connecting extension modules of two different types: MOD1-3. 3 external terminals are output for MOD1 slot and 3 - for MOD2 slot.
Stackable input-output modules are docked with a side connector on the WB6 case right side; each module adds 8 to 16 digital or analog ports to the controller.
Up to 8 modules can be connected in series: up to 4 input modules (type I) and up to 4 output modules (type O and IO).
Backup power module — additional board, installed on the second level(mezzanine) of the WB case on the DIN-rail. Contains Li-Ion (Li-Pol) battery with capacity of 2200 mAh, provides controller operation up to 3 hours.
Wireless interfaces
Cellular communication module is a 2G (GPRS), 3G (UMTS) or NB-IoT modem, installed in the controller during manufacture. Requires a MicroSIM card.
The modem allows you to send and receive SMS, connect to the Internet. Work with two SIM-cards in multiplexing mode. In Wiren Board 6.0 -6.4 controllers. Both connectors are located on the side surface of the controller. In Wiren Board 6.5 controller, microSIM 1 connector is moved to the front row of terminals.
Wi-Fi of the Wiren Board can be configured to work in one of three modes:
in hotpoint mode, enabled by default (the name is WirenBoard without password, the address of the controller in the generated network is: 192.168.42.1)
- client mode
- simultaneous operation in both hotpoint and client modes
Bluetooth 4.0 (Bluetooth Low Energy) — you can track the proximity of other Bluetooth devices, such as a mobile phone or Bluetooth tag.
USB stick Z-Wave - connects to the USB connector and provides support for Z-Wave devices.
433 МHz — radio module RFM69H is installed in the controller during production (in versions up to 6.4). Allows you to connect Noolite devices, Oregon sensors to the controller.
In the version of WB6.5 433 Mhz radio module is available asan extension module.
Wi-Fi, GSM and 315/433 MHz radio antennas are connected to SMA connectors.
If the GSM signal is weak, it is recommended to use a remote antenna and place it away from the controller.
Wired interfaces
Ethernet supports speed up to 10/100 Mbit/s. Wiren Board 6 controller is equipped with two such interfaces.
The controller is equipped with two USB 2.0 (A/F) ports. Both ports operate in USB Host mode; in future versions of the controller, the first port (closest to the Ethernet connector) will support loading the controller firmware. Power control of individual USB devices is described in the article Power for USB ports.
RS-485 — two-wire bus communication standard.
The controller has 2 RS-485 ports + 2 more ports can be added by RS-485 extension modules .
The article will help you to choose and lay the bus cables correctly.
Configuration of the devices is provided in the web interface.
Basically in Wiren Board, driver WB-mqtt-serial works through the system of MQTT-messages with connected RS-485 devices.
CAN — is the standard of communication over a two-wire bus.
The controller is multiplexed (output to the same terminals) with a second RS-485 port.
1-Wire — is a bus for connecting external sensors on two or three wires. Since this is a bus, you can connect multiple devices to the same 1-Wire port. The controller software supports connection of DS18B20 type temperature sensors.
It is convenient to use +5V output to power the sensors. It is protected from short circuit and high voltage supply. When the controller is powered by a battery, the +5V output remains active. Software control of this output is also supported (it can be disabled).
Universal inputs/outputs A1-A4
Universal channel Ah combines three functions and can work as:
- open collector output is a key (3A/30V), closing output to the ground
- ADC with a measurement range of 0 — 28 V
- Digital input — is triggered when the voltage at the terminal is 5 V
W1-W2 channels
The W1 and W2 channels can work as an interface for connecting 1-Wire sensors (default) or as digital inputs "dry contact"type. Note that in the discrete input mode, the trigger occurs when the Wx signal is earthed (GND terminal block), unlike the A1-A4 channels (above).
The mode of each channel is selected independently in the controller configuration. Through the web interface, the desired configuration is located in the section Configs => Hardware Module Configuration => W1 terminal mode.
Multiple DS18B20 temperature sensors can be connected to each channel via a loop: depending on the loop length, the maximum number of sensors is 10 to 20 (the limit is 20 sensors per 5m cable connected by a star). Additional sensors can be connected via the WBE2-I-1-WIRE module.
Terminal blocks
Some terminal blocks can be used to perform more than one function. See the detailed description in the Multiplexing ports article.
sign |
Max. V, I | state by default | Functions | ||||
Top row, left block | |||||||
---|---|---|---|---|---|---|---|
Vin | 40V (WB6.3,6.4)
52V (WB6.5) |
Input voltage, reverse polarity protection | |||||
GND | "ground", minus power supply | ||||||
Top row, right block | |||||||
O1-O3 | Inputs/outputs of the 1st extension module | ||||||
O1-O3 | Inputs/outputs of the 2nd extension module | ||||||
Bottom row, right block | |||||||
A1-A4 | 40V , 1A | High Z | Open collector outputs, ADC | ||||
GND | For easy connection of external sensors | ||||||
W1 | 40V | 5V | 1-Wire, GPIO | ||||
W2 | 40V | 5V | 1-Wire, GPIO | ||||
5V out | 5V, 0.5A | 5V | The 5V output. Shutdown current is exceeded. Software on-off switching. | ||||
A | 40 V | 0V | port RS-485 (/dev/RS-485-1) | ||||
B | 40 V | +5V | |||||
L | 40 V | 0V | Port CAN or RS-485 (/dev/RS-485-2) .
Connecting RS-485: A to terminal A|L, B to terminal B|H. | ||||
H | 40 V | +5V | |||||
Vout* | 1A | Supply output. Input voltage, software on-off switching. |
In the 6.3 revision of Wiren Board controller terminals of "type 250" were applied as front-end terminals.
These are self-locking clips. When the cleaned single wire is inserted into the socket, it is automatically clamped with a spring latch.
To insert a stranded conductor, it is necessary to press the spring button clips (or use insulated pin lugs of the bushing isolated pin tips).
The button has a slot for a screwdriver.
To remove the wire, you need to press the spring by pressing the clip button, and pull out the wire.
In versions starting from WB6.4 detachable screw terminals "series 15EDG" with a pitch of 3.5 mm were applied as interface terminals. When screwing, do not make a lot of effort!
Ports and interfaces
Debug port — by connecting to it, you can directly access the controller console. Through it you can also interact with the bootloader and monitor the operating system boot (serial console).
"Buzzer" — beeps, its frequency is adjustable.
The real-time clock is powered by an internal backup battery.
Watchdog
The controller contains a separate hardware watchdog that reboots it entirely on power when the software freezes.
Power Supply
The controller has three external inputs for power connection:
- DC jack - standard plug connector (5.5x2.1mm) on the left side of the case.
- VIN and GND terminals: two VIN terminals to which two independent power supplies can be connected for redundancy. The grounds of the power supplies must be connected and connected to the GND terminal.
- Power-over-Ethernet (PoE Passive). Read more Power over Ethernet.
It is possible to simultaneously connect the sources to different inputs, including different voltages.
For backup power, you can connect the internal extension module WBMZ2-BATTERY with Li-Ion (Li-Pol) battery.Important: when the controller is supplied with a battery module, the controller does not turn on immediately when the power is supplied. To turn it on, press the power button of the module under the top cover of the controller. See article WBMZ2-BATTERY.
The valid power range is 9 — 36 V for WB rev.6.1 - 6.4.1 , anda 9 — 48 for WB6.5. The average consumption of the Board is 1.5 — 2 watts. But since the GSM module consumes up to 8W impulsively, it is recommended to use power supplies with a power of at least '10W'.
Supported Devices
Devices of our production with the RS-485 interface
Connection of peripheral devices
The wiring on the terminal blocks of Wiren Board devices
Features of controller network settings
Wiren Board 6: Installing On The Remote Site
Detailed technical description of the controller board
The article Wiren Board 6: Hardware describes some of the features of work and the device inputs, the power supply circuit of the controller.
Hardware errors/features of Wiren Board 6 found in the operation of the controller.
Hardware revisions — the description of changes in the controller board.
The table of processor and GPIO signals match on the board according to the revisions: Wiren Board 6.0.1, Wiren Board 6.1, Wiren Board 6.2 and above
Working with GPIO — how to work directly with GPIO.
Firmware update. To reset the Wiren Board 6 to factory settings (factory reset), use the instructions in the section The Wiren Board 6 factory reset
Wiren Board 6: WB6 root password recovery
Summary table of characteristics
General | |
---|---|
Processor | NXP i.MX 6ULL 800 MHz Cortex A7 ( 500MHz and 900MHz upon request) |
RAM | DDR3 SDRAM 512 MB |
Non-volatile memory | 4 GB eMMC |
Dimensions | DIN railed Enclosure 6Units
106.25x90.2x57.5 mm. Without the case: 103x87x20 mm. |
Operation | operating temperature 0...+70С/-40..+85С
(depending on the configuration). |
Terminals and wire section | |
The recommended wire cross section with pin bushing insulated tip, mm2 | 0,75 — 1 |
Standard sleeve length of pin bushing insulated tip, mm | 8 |
Tightening torque of screws, Н∙м | 0,2 |
Interfaces | |
RS-485 | 2 |
CAN | 1 (multiplexed with RS-485) |
Wx ports ( 1-Wire/DI) | 2 |
Ax ports (DI / Analog input / open collector output) | 4 |
Communication ports | |
Ethernet 10/100 | 2 (with passive PoE) |
USB Host | 2 |
Wi-Fi 802.11n | 1 (AP, client)* |
Bluetooth 4.0 | 1* |
Cellular communication | 2G / 3G / 2G+NB-Iot or without modem * |
SIM cards | 2 x microSIM, simultaneous operation of 2 cards is not supported |
Power | |
Voltage | 9 - 36V DC |
Power supply circuit | from high voltage input |
Terminal inputs | 2 |
DC jack | 1 |
Ethernet power | 1 (1st port) |
Power outputs for external devices | |
Vout | input power - with current limit, program shutdown and status monitoring |
5Vout | 5V - with current limitation, disabling the software, measure the output voltage |
"'Modularity'" | |
Slots for internal extension modules of type WBE2 and WBE2R | 2 |
Slots for internal extension modules such as WBE2S and WBE2R | 1 |
Connector for external input/output modules WBIO | |
Connector for mezzanine power module (battery, supercapacitors, filters) | 1 |
"'Bundled software'" | |
Operating system | Linux Debian 9 "Stretch". Mainline kernel 4.9. |
Serial port protocol support | Modbus RTU, mercury, Milur, pulsar, IVTM, etc. |
Protocol support when installing extension modules | Z-Wave, KNX |
Protocol support via IP | KNX IP, Modbus RTU-over-TCP, SNMP |
Built-in Web interface | Adding devices, settings, visualization, mimics |
Scripts | Rules wb-rules in JavaScript, editing via Web-interface. Support for Node-RED scripting |
Visualization | Table view, mimics in the built-in Web-interface. |
Mobile devices | Responsive web interface. Integration with third-party mobile applications: MQTT Dash, iRidium. Supported by the user community: home kit. |
Archive | history storage Module of wb-mqtt-db channels values, up to 1GB of data |
Software update | Individual components via APT, full firmware with backup via Web and USB flash |
Sending data to top-level SOFTWARE | MQTT, Modbus TCP, Zabbix API, etc. |
Top level software support | SAYMON, Zabbix, Nagios, Unimon, Grafana, Master SCADA, Rapid SCADA and others |
Other | Easy installation of thousands of packages from Debian, nodejs, python repositories, etc.
|
Images and drawings of the device
You can download images and drawings of different models of Wiren Board 6' controllers via the links below.