История
19 августа 2022
Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.»
−149
Нет описания правки
−56
Нет описания правки
−40
Нет описания правки
−95
Обновление для соответствия новой версии исходной страницы.
+457
17 августа 2022
Нет описания правки
+5
Нет описания правки
−2
Нет описания правки
+2
Нет описания правки
+5
Нет описания правки
+2
Нет описания правки
−3
Нет описания правки
+25
Нет описания правки
+29
Нет описания правки
+11
Нет описания правки
+3
Нет описания правки
+1
Нет описания правки
−1
Нет описания правки
+3
Нет описания правки
+9
Нет описания правки
+11
Нет описания правки
−7
Нет описания правки
−22
Нет описания правки
+4
Нет описания правки
+7
Нет описания правки
−4
Нет описания правки
+21
Нет описания правки
+9
Нет описания правки
−1
Нет описания правки
−40
Нет описания правки
−21
Нет описания правки
+32
Нет описания правки
+27
Нет описания правки
+339
Нет описания правки
+10
Новая страница: «# Put the back cover controller up. # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with professional latches. # Use a screwdriver to bend the remaining latches and get the cover. # Lightly bend the side wall of the case where the connector for connecting external modules is located, and push the controller connector out of the case. He did not become high-r...»
−400
Обновление для соответствия новой версии исходной страницы.
+23
Нет описания правки
+1
Нет описания правки
+13
Обновление для соответствия новой версии исходной страницы.
+40
FuzzyBot переименовал страницу Разбираем корпус контроллера/en в Disassembling the controller case/en без оставления перенаправления: Часть переводимой страницы Разбираем корпус контроллера.
мНет описания правки
−4
Новая страница: «<gallery mode="packed" heights="160px"> Image: Cover_rem1.jpg | Step 1 Image: Cover_rem2.jpg | Step 2 Image: Cover_rem3.jpg | Step 3 </gallery>»
−6
Новая страница: «'''Step 3'''. Remove the cover.»
−13
Новая страница: «'''Step 2'''. Pry out the latches on the controller cover with a flathead screwdriver.»
−34
Новая страница: «'''Step 1'''. Lay the controller face up.»
−56
Новая страница: «===Cover removing=== It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid.»
−118
Новая страница: «<gallery mode="packed" heights="150px"> Image: 4_latches.png | Step 1 Image: Case2.jpg | Step 2 Image: Case4.jpg | Step 3 Image: Case5.jpg | Step 4 </gallery>»
−4
Новая страница: «'''Step 4'''. Install the back cover. Lid latches should click into place.»
−72
Новая страница: «'''Step 3'''. Easily bend the side wall near the connector housing for connecting side modules. With a light insertion, press the pulp into the housing so that the connector enters the opening in the side wall of the housing.»
−119
Новая страница: «'''Step 2'''. Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.»
−135