Start page

Product catalog

Controllers

Wiren Board is a universal Linux-based controller for automation with open source software. Designed for home and industrial automation and monitoring: polling of sensors and meters, data acquisition and transmission, for usage in automatic systems for commercial accounting of power consumption and in Smart Home systems.

Automation controller Wiren Board 6

Wiren Board is designed for home and industrial automation and monitoring. It is suitable for polling sensors and meters, for sensors and meters data acquisition, and as a transmission device, as a replacement of programmable logic controllers, in SCADA and in Smart Home systems. The number of ports and interfaces supported and the user-friendly Web interface allow you to use the Wiren Board as a Smart Home master controller working together with wireless and wired devices from other manufacturers. Protection of ports from excessive voltage surges, the enclosure compatible with a DIN rail, the watchdog timer allow you to use the Wiren Board controller in solutions where the reliability of operation is of utmost importance.

14 900 ₽

Demo kit WB-demo-kit

WB-demo-kit is an assembled and programmed set of the equipment for demonstration to the customers or for independent fast mastering of Wiren Board devices.

The demo-kit equipment and programmed rules show common usage scenarios of Wiren Board devices:

indoor air quality control
climate control
monitoring of flooding in inhabited and production locations
polling of water and electric power meters
lightning control
multi-circuit electricity metering
equipment failure warning and prevention in some cases
stable system operation in case of power outage or loss

WB-demo-kit is delivered with detailed documentation: complete diagram of connection, power supply diagram, detailed description of scenarios.

Prices are indicated on a turnkey basis.

64 400 ₽

Extension modules for Wiren Board controllers

Wiren Board controllers can be easily customized for specific tasks with extension and input-output modules.

Extension modules are small circuit boards designed to be installed inside a controller. They expand the functionality of a controller by adding additional interfaces.

Stackable modules for input-output are stacked together with a controller on a DIN-rail by adding 8-16 digital and analog ports.

Battery module WB-UPS

Uninterruptible power supply module on lithium polymer batteries. It is used to maintain the operation of the controller and connected modules in case of power loss.

It has two modes of operation-12/24V, the mode is selected by a switch.

4 000 ₽

Battery module WB-UPS v.2

Модуль бесперебойного питания на литий-полимерных аккумуляторах. Служит для поддержания работы контроллера и подключенных модулей при отсутствии напряжения питания.

Имеет два режима работы - 12/24В, режим выбирается переключателем.

4 000 ₽

Input-output extension module WBIO-DI-WD-14

Consists of 14 universal inputs("dry contact" type/ low voltage presence with group galvanic isolation). The operating mode depends on the selected connection scheme. The module can operate in both modes simultaneously.

2 500 ₽

Input-output extension module WBIO-AI-DV-12

Designed for measuring values of analog signals. Typical uses of this module include acquisition of data from analog thermometers, measurement of voltage at individual elements of a battery, etc.

Warning: only one such module can be connected to the controller!

3 500 ₽

WBIO-AI-DV-12/4-20mA

Input-output extension module WBIO-AI-DV-12/4-20mA

Designed for measuring 4-20 mA analog signals. A typical use for this module is retrieving data from sensors with current output: thermometers, pressure sensors, etc.

Warning: only one such module can be connected to the controller!

3 500 ₽

Input-output extension module WBIO-AO-10V-8

Designed to control up to 8 servos or dimmers with 0-10 V of voltage.

This module is not compatible with the WB-MIO(E) bus coupler

3 700 ₽

Input-output extension module WBIO-DO-HS-8

Designed for managing low-voltage loads such as relays, low voltage motors, signal lamps, etc.

2 200 ₽

Input-output extension module WBIO-DO-SSR-8

Designed for managing low voltage loads, devices with dry contact inputs. The devices do not require common ground with the controller

2 000 ₽

Input-output extension module WBIO-DO-R10A-8

Designed for managing lighting, motors, contactors

2 900 ₽

Input-output extension module WBIO-DO-R10R-4

Special configuration of outputs designed for controlling motorized curtains, roller blinds, shut-off valves

2 900 ₽

Input-output extension module WBIO-DO-R1G-16

Designed for managing contactors, signal lamps and other low power loads

5 000 ₽

Input-output extension module WBIO-DI-HVD-16

Designed for monitoring the status of circuit breakers, polling signal lamps etc.

3 300 ₽

Input-output extension module WBIO-DI-HVD-8

Designed for monitoring the status of circuit breakers, polling signal lamps etc.

2 200 ₽

Модуль расширения WBC-2G

Двухсимочный модуль расширения, добавляет поддержку 2G сети. Устанавливается в разъем на плате контроллера Wiren Board 6.7. В комплекте идет угловая антенна, её подключение производится через разъём SMA.

1 800 ₽

Модуль расширения WBC-3G

Двухсимочный модуль расширения, добавляет поддержку 3G сети. Устанавливается в разъем на плате контроллера Wiren Board 6.7. В комплекте идет угловая антенна, её подключение производится через разъём SMA.

3 500 ₽

Модуль расширения WBC-NB

Двухсимочный модуль расширения, добавляет поддержку сети NB-IoT. Устанавливается в разъем на плате контроллера Wiren Board 6.7. В комплекте идет угловая антенна, её подключение производится через разъём SMA.

3 500 ₽

Модуль расширения WBC-4G

4G (LTE) модем. Устанавливается в контроллер Wiren Board 6.7. В комплекте идет угловая антенна, подключается через разъём SMA.

3 300 ₽

WBE2R-R-ZIGBEE + antenna

Extension module WBE2R-R-ZIGBEE + antenna

Adds a ZigBee interface. It is installed in the connector on the controller board. For Wiren Board 6.

Wi-Fi antenna is included, connection is made through the SMA-male connector.

ZigBee is a wireless communication standard as Wi-Fi and Bluetooth, created specifically for the Internet of things: from home automation (control of light, household appliances, audio-video equipment) to the construction of monitoring systems for large industrial facilities (temperature control and vibration of devices, collection of readings of electricity, water and gas consumption sensors, survey of fire and security sensors, etc.). ZigBee is used by all large companies in the smart home market.

2 000 ₽

Extension module WBE2-AO-10V-2

Dual-channel module with 0-10V analog outputs. Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower

1 500 ₽

Extension module WBE2-DI-DR-3

Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower

700 ₽

Extension module WBE2-DO-OC-2

Installed in the extension module connector in the controller enclosure. Two "open collector"type outputs. Current up to 1 A, 30 V DC. This module is not compatible with Wiren Board version 5 and lower

700 ₽

Extension module WBE2-DO-R6C-1

Consists of a single SPDT (changeover contact) relay. Maximum current for resistive load: 6a for 230VAC or 30VDC. Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower

700 ₽

Extension module WBE2-DO-SSR-2

Consists of two SPST (normally open) optorelays with a single common contact. Current up to 400 mA, voltage up to 40VDC. Switch-on resistance < 2 Ohms

Equipped with 40V TVS diodes for transient overvoltage protection when switching inductive loads. Installed in the extension module connector in the controller enclosure.

This module is not compatible with Wiren Board version 5 and lower

700 ₽

Extension module WBE2-I-1-WIRE

Auxiliary 1-Wire port. Plugs into a connector on the controller board. This module is not compatible with Wiren Board version 5 and lower

700 ₽

Extension module WBE2-I-KNX

Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower

5 000 ₽

Extension module WBE2-I-RS232

Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower.

700 ₽

WBE2-I-RS485-ISO

Extension module WBE2-I-RS485-ISO

Auxiliary galvanic isolated RS-485 port. Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower

1 200 ₽

Extension module WBE2R-R-GPS

Plugs into a connector on the controller board. Determination of coordinates. Standard time signal. This module is not compatible with Wiren Board version 5 and lower

1 900 ₽

Extension module WBE2S-MICROSD

Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower

1 000 ₽

Battery module for Wiren Board 6 WBMZ2-SUPERCAP

Встраиваемый источник бесперебойного питания на ионисторах для Wiren Board версий 6.3-6.6. Модуль питает сам контроллер, модули расширения и ввода-вывода, и подключенные через клеммы 5Vout, Vout и USB внешние устройства.

WBMZ2-SUPERCAP устанавливается вторым этажом в корпус контроллера и подключается шлейфом к внутреннему разъему.

Модуль имеет ограничение по мощности и времени работы (2-3 мин).

2 200 ₽

Модуль резервного питания WBMZ3-SUPERCAP

Встраиваемый источник бесперебойного питания на ионисторах для Wiren Board версии 6.7 (последняя). Модуль питает сам контроллер, модули расширения и ввода-вывода, и подключенные через клеммы 5Vout, Vout и USB внешние устройства.

WBMZ3-SUPERCAP устанавливается в корпус контроллера в разъем для модулей резервного питания.

Модуль имеет ограничение по мощности и времени работы (2-3 мин).

2 200 ₽

Battery module for Wiren Board 6 WBMZ2-BATTERY

Built-in uninterruptible power supply for Wiren Board 6. The module powers the controller, its extension and I/O modules and external devices connected via 5Vout, Vout and USB terminals.

The WBMZ2-BATTERY is installed as a second level into the controller enclosure and attached via ribbon cable to an internal connector. A button for forced shutdown of the controller is provided on the module board.

The module is limited in power and is intended for small-scale systems.

2 200 ₽

Battery module for Wiren Board 6 WBMZ3-BATTERY

Встраиваемый источник бесперебойного питания для Wiren Board версии 6.7 (последняя). Модуль питает сам контроллер, модули расширения и ввода-вывода, и подключенные через клеммы 5Vout, Vout и USB внешние устройства.

WBMZ3-BATTERY устанавливается в слот для модулей резервного питания в корпус контроллера.

Модуль имеет ограничение по мощности и предназначен для небольших инсталляций.

2 200 ₽

Relay modules

WB-MR are relay modules (contactors) controlled via Modbus RTU. They are used for switching various load types: lighting, ventilation, heated floors, equipment power supply units etc.

The product line includes modules with a large selection channels and load capacities. We are particularly proud of our relay modules designed for direct control of loads with high inrush current (up to 800A) eliminating the need for a separate contactor: LED lighting, incandescent lamps etc.

...

6-channel relay module WB-MR6C

New WB-MR6C v.2 with more powerful relays is available for ordering.

Designed for direct control of low-power loads (rated current 7 A) and contactors

3 200 ₽

6-channel relay module WB-MR6C v.2

Designed for direct control of LED, incandescent and fluorescent lighting and other loads.

Each output is rated 10A and can withstand inrush current as high as 80A and continous load of up to 16A.

Also used as general-purpose discrete input/output module.

3 500 ₽

Relay module 6-channel WB-MR6

Relay module with high in-rush current capacity for lighting management and switching general purpose loads. Designed for industrial and home automation systems.

The module is designed to control loads up to 10A rated (16 A peak current) without contactors. It is equipped with a special input for simultaneous cutoff of all loads.

from 4 500 ₽
to 5 800 ₽

6-channel relay module WB-MR6C/NC

Normally closed relays. Designed for direct control of low-power loads (rated current 2 A), which don't have inrush current, i.e. contactors.

Not suitable to control power supplies and LED lamps.

3 200 ₽

6-channel relay module WB-MR6CU

Designed for direct control of low-power loads (rated current 7 A) and contactors.

Does not support switching of power supplies and LED lamps.

3 200 ₽

Relay module 3-channel WB-MR3

Relay module with high in-rush current capacity for lighting management and switching general purpose loads.

from 3 100 ₽
to 3 400 ₽

Relay module 6-channel WB-MRPS6/S

Compact relay module with high in-rush current capacity for lighting management and switching general purpose loads.

4 200 ₽

Relay module 3-channel WB-MRWL3

Designed for switching general purpose high-power loads, including induction loads: control groups of outlets, motors, heaters, etc. Rated load up to 20A (4.5 kW) per channel.

3 600 ₽

Relay module 2-channel WB-MRM2-mini

Compact relay module. Installable in a junction box.

from 2 000 ₽

Energy meters

The WB-MAP energy meters are used for industrial metering installations in apartment houses and office buildings as well as for monitoring consumers in data centers and smart offices. They can operate in single phase or three phase AC networks.

These multi-branch energy meters take significantly less space in a cabinet compared to traditional single-circuit energy meters.

External split-core current transformers allow for installation on live circuits with zero downti...

Измеритель параметров электрической сети WB-MAP12E

The WB-MAP12E multi-circuit energy meter is an ideal choice for industrial metering installations in apartment houses and office buildings as well as for monitoring energy usage in data centers and smart offices. Designed for operation in single phase or three phase AC networks.

External split-core current transformers allow for installation on live circuits with zero downtime.

The WB-MAP12E can measure inrush currents of various equipment, such as lighting features or motors. It can detect and measure voltage surges as well.

Recognized as metering equipment with accuracy class 0.5S by Russian government body. Registration number is 79082-20.

from 11 800 ₽
to 73 400 ₽

Energy meter WB-MAP3E

The WB-MAP3E energy meter is an ideal choice for industrial metering installations in apartment houses and office buildings as well as for monitoring consumers in data centers and smart offices. Designed for operation in single phase or three phase AC networks.

External split-core current transformers allow for installation on live circuits with zero downtime.

The WB-MAP3E can measure inrush currents of various equipment, such as lighting features or motors. It can detect and measure voltage surges as well.

Recognized as metering equipment with accuracy class 0.5S by Russian government body. Registration number is 79082-20.

from 4 500 ₽
to 20 450 ₽

Multi-channel meter WB-MAP6S

The WB-MAP6S energy meter is perfect for consumption analysis in apartments and private homes. It is designed for operation in single phase AC networks.

from 3 500 ₽
to 34 600 ₽

Multi-channel meter WB-MAP12H

The WB-MAP12(H) energy meter is an ideal choice for industrial metering installations in apartment houses and office buildings as well as for monitoring consumers in data centers and smart offices. Designed for operation in single phase or three phase AC networks

from 11 800 ₽
to 75 800 ₽

Current transformer 20А, 6mm KCT006

One split type current transformer for use with WB-MAP series of energy meters. Recommended to order with WB-MAP energy meters

450 ₽

Current transformer 75А, 10мм KCT-10

One split type current transformer for use with WB-MAP series of energy meters. Recommended to order with WB-MAP energy meters

450 ₽

Current transformer 120А, 16мм KCT016

One split type current transformer for use with WB-MAP series of energy meters. Recommended to order with WB-MAP energy meters

550 ₽

Current transformer 200А, 24мм CTSA024

One split type current transformer for use with WB-MAP series of energy meters. Recommended to order with WB-MAP energy meters

1 400 ₽

Current transformer 400А, 35mm CTSA035

One split type current transformer for use with WB-MAP series of energy meters. Recommended to order with WB-MAP energy meters

2 200 ₽

Sensors

In order to create comfortable environment, it is necessary to control the level of carbon dioxide, lighting, temperature, humidity, noise level and the presence of dangerous gases. The devices support standard industrial protocol Modbus RTU so they can work with any PLC-system.

WB-MSW v.3 wall sensor

Modbus sensor WB-MSW v.3 wall sensor

Hybrid digital sensor of temperature, humidity, illumination, noise, CO2 and VOC level. It is equipped with the IR blaster (and the receiver for learning). Designed for climate control in residential and office premises.

from 3 000 ₽
to 9 900 ₽

Bus coupler for digital thermometers WB-M1W2

Compact module for polling two remote digital 1-Wire temperature sensors over the RS-485 bus. Allows the use of 1-Wire sensors in conditions of strong interference (e.g. a high-energy power supply operating nearby) and at a considerable distance from the controller.

1 300 ₽

Temperature sensor 1-wire DS18B20

Waterproof digital temperature sensor DS18B20.Waterproof, cable length 1, 3, 5 or 10 m. Temperature range -55°C to +125°C accuracy ± 0.5°C (-10°C to +85°C).

each device has its unique address
connect up to 30 sensors with Wiren Board controller port
Convenient replacement of thermistors pt100/pt1000 in some automation tasks

from 400 ₽
to 2 000 ₽

Combined sensor WB-MS

Combined digital temperature, humidity, illumination and noise level sensor.

from 2 000 ₽
to 5 000 ₽

WB-MAI2-mini / СС

Analog input module WB-MAI2-mini / СС

The module transmits data of two 0-20 mA signals via Modbus RTU.

For installation in a junction box.

Dimensions 57 х 18 х 14 mm

1 500 ₽

Analog input module WB-MAI

Designed to measure voltage, current, resistance, temperature; connect signals of "dry contact" and "open collector" types. The input mode is selected when configuring the device. The module is managed from the controller or PC via RS-485 bus by MODBUS commands.

6 900 ₽

Dimmers

We produce dimmers for incandescent lamps, LED lamps, and dimmers for LED RGB (W) strips.

LED Dimmer WB-MRGBW-D

4-channel dimmer designed to control a single LED strip of RGB or RGB+W type or four single-color strips.

2 400 ₽

LED and incandescent lamps dimmer WB-MDM3

Designed for dimming incandescent lamps, this dimmer also supports dimming LED bulbs, LED strips’ drivers, electronic power transformers driving halogen lights, etc.

Supports leading-edge and trailing-edge dimming.

Can be used to control the speed of a fan.

5 600 ₽

Other

Devices produced by Wiren Board that did not fit into other categories

Infrared controlled modules
Ethernet gateways
Water metering and leakage control
1-Wire sensors

8-channel pulse counter module WB-MCM8

Pulse counter module for connecting water, electricity, gas, and other types of meters with pulsed outputs of dry contact or open collector type

2 500 ₽

Interface converter WB-MGE

The WB-MGE bus coupler is designed for remote connection of Modbus RTU devices with RS-485 bus via Ethernet (Modbus RTU over TCP protocol). The module can be connected directly to the controller, as well as via local network or the Internet.

3 500 ₽

Interface converter WB-MIO

Designed for remote connection of WBIO devices (I/O modules) using the Modbus protocol over the RS-485 bus.
Allows you to separate the I/O modules from the Wiren Board controller and move them to another DIN rail or into another electric cabinet.
This bus coupler allows you to use the I/O modules as standalone devices with third party controllers.

2 000 ₽

Interface converter WB-MIO-E

Designed for remote connection of WBIO devices (I/O modules) using the Modbus protocol over the RS-485 bus and/or Ethernet.

Allows you to separate the I/O modules from the Wiren Board controller and move them to another DIN rail or into another electric cabinet.

This bus coupler allows you to use the I/O modules as standalone devices with third party controllers.

3 500 ₽

Infrared control device WB-MIR

Learning module with infrared transmitter. Controls air conditioning units, fan coils, TV sets etc. The module is managed by a controller or PC via RS-485 through Modbus RTU protocol commands.

The device is equipped with an internal temperature sensor (NTC thermistor).

2 200 ₽

Water metering and leakage control module WB-MWAC

Everything you need for the typical task of monitoring the wet core of the apartment:

water leak detection,
automatic control of shut-off valves,
counting pulses from water meters even in case of power loss

5 500 ₽

Module analog output 0-10В WB-MAO4

The 4-channel lighting control module is designed to control lighting fixtures equipped with 0-10V interfaces, PWM, as well as to manage arbitrary loads equipped with compatible inputs.

Available upon request.

3 500 ₽

Components

Components and additional devices by other manufacturers.

Wall power supply

Power supply for a socket Wall power supply

Plug in power supply unit, 12 VDC, 1A, compatible to the Wiren Board controllers up to version 6.

550 ₽

DIN Rail Power Supply HDR-15-24

Power supply model HDR-15-24 from the manufacturer MEAN WELL

990 ₽

DIN Rail Power Supply HDR-30-24

Power supply model HDR-30-24 made by MEAN WELL

1 400 ₽

Power supply Passive PoE

Wiren Board controllers support Passive Power over Ethernet with supply voltages ranging from 7 to 36 volts.

500 ₽

19″ panel with a DIN rail

Mounting equipment 19″ panel with a DIN rail

The bracket is designed for mounting on a DIN rail in a server equipment rack. To be used in all series of telecommunication cabinets and racks

2 400 ₽

USB-stick Z-Wave.Me UZB1

The Z-Wave.Me Z-Stick 4 USB stick allows you to connect your Wiren Board controller to the Z-Wave network. Wiren Board requires additional software to control Z-Wave devices. Supports standard Zensys API (SerialAPI) and is compatible with commonly used software packages such as HomeSeer, Z-Command, mControl, Linux MCE.

7 600 ₽

External remote 3G antenna

Antenna External remote 3G antenna

External remote 3G antenna with magnetic base, SMA connector (male). RG174 cable. Cable length 2m. Antenna height 24 cm Designed for use with the Wiren Board controller to increase the range of the GSM module.

500 ₽

External remote antenna 433 MHz

Antenna External remote antenna 433 MHz

External remote antenna on magnetic base, frequency 433 MHz, SMA connector.
Cable length 1.8 m. Cable RG174.
Designed for operation with the Wiren Board radio module to increase its operating range.

500 ₽

Antenna antenna

Antenna with an SMA connector

200 ₽

GSM R/A angular

Antenna GSM R/A angular

Antenna with an SMA connector

150 ₽

GPS/GLONASS external antenna

Antenna GPS/GLONASS external antenna

GLONASS/GPS external active antenna GKZS-GNSS-015.
To connect to the Wiren Board 4 controller, use the u.FL-SMA adapter.

690 ₽

Antenna Wi-Fi antenna

Dipole antenna for Wi-Fi and Bluetooth (2.4 GHz) with an RP-SMA connector. Length: 10.5 cm.

For Wiren Board 4, 5, 6 controllers.

290 ₽

Insulated wire ferrules 100 pcs 0,5-8

Insulated wire ferrules are designed for mounting on the ends of stranded copper wires for the formation of the integrity at the end of the wire when connected to the contact sockets of the electrical equipment. Modern solution when connected to the terminals of electrical appliances, replaces the laborious process of maintenance or twisting stranded copper wires.

from 180 ₽
to 300 ₽

twin wire ferrules

Twin wire ferrules 100 pcs twin wire ferrules

Insulated twin wire ferrules are designed for mounting on the ends of stranded copper wires for the formation of the integrity at the end of the wire when connected to the contact sockets of the electrical equipment. Modern solution when connected to the terminals of electrical appliances, replaces the laborious process of maintenance or twisting stranded copper wires.

from 350 ₽
to 660 ₽

ParLan Patch F/UTP Cat5e PVC 4х2х0,60 sq.mm

LAN Cable ParLan Patch F/UTP Cat5e PVC 4х2х0,60 sq.mm

The сable is used in low-cost installations for laying RS-485 networks instead of the indoor signal cable. One of the four twisted pairs is used for signals A and B, and the other two pairs are used for power.

The symmetrical ParLan Patch F/UTP Cat5e 4x2x0,60 PVC cable is used in digital telephony, Ethernet networks, as well as in video monitoring, alarm and ACS systems. The design contains 4 twisted pairs (multi-wire twisted pair conductors) in dense PE insulation with individual color coding according to international standards. The outer shell of PVC plastic fully meets the requirements of the PB. Resistant to electromagnetic influences and radio frequency interference.

The price is for 1m.

60 ₽

Discontinued

Discontinued, deprecated devices and models that are not recommended for future projects

Multi-channel meter WB-MAP3H

The WB-MAP3H energy meter is an ideal choice for industrial metering installations in apartment houses and office buildings as well as for monitoring consumers in data centers and smart offices. Designed for operation in single phase or three phase AC networks

Product is no longer available to order - contact us

16-channel pulse counter module WB-MCM16

This model is discounted, WB-MCM8 is a recommemded replacement.
Pulse counter module for connecting water, electricity, gas, and other types of meters with pulsed outputs of dry contact or open collector type

Product is no longer available to order - contact us

Wiren Board 6 Zero

Automation controller Wiren Board 6 Zero

Wiren Board 6 Zero is a controller based on the newest Wiren Board 6 platform with an optimized set of ports and interfaces. It comes with a preinstalled iRidium server (60 day trial) and a basic Wiren Board Web interface (free of charge).

Iridium server is a platform for smart home and IoT controllers known to developers in 25 countries for its convenience in design, configuration flexibility and ease of use.
You can use it to tailor the interface to manage both smart home and smart office from portable and stationary devices, configure remote control and scenarios.

Examples of iRidium projects.

from 8 500 ₽
to 9 500 ₽

LED and incandescent lamps dimmer WB-MDM2

This model has been discontinued. Please use WB-MDM3 instead.

Designed for dimming incandescent lamps, this dimmer also supports dimming LED bulbs, LED strips’ drivers, electronic power transformers driving halogen lights, etc.

Supports leading-edge and trailing-edge dimming.

Can be used to control the speed of a fan.

Product is no longer available to order - contact us

LED Dimmer WB-MRGB-D

This model has been discontinued. It has been replaced by the WB-MRGBW-D model. For gross purchases please contact us info@contactless.ru.

Three channel dimmer for managing LED strips. Can manage one RGB strip or three monochrome strips individually

Product is no longer available to order - contact us

Automation controller Wiren Board 5

Obsolete. Recommended replacement is Wiren Board 6.

Wiren Board is designed for home and industrial automation and monitoring. It is suitable for polling sensors and meters, to be used as a data acquisition and transmission device, as a replacement of programmable logic controllers, in SCADA and in Smart Home systems.

The number of ports and interfaces supported and the user-friendly Web interface allow you to use the Wiren Board as a Smart Home master controller working together with wireless and wired devices from other manufacturers. Protection of ports from excessive voltage surges, the enclosure designed to be mounted on a DIN rail, the watchdog timer allow you to use the Wiren Board controller in solutions where the reliability of operation is of utmost importance.

Product is no longer available to order - contact us

LED Dimmer WB-MRGB

This model has been discontinued. It has been replaced by the WB-MRGBW-D model.

Three channel dimmer for managing LED strips. Can manage one RGB strip or three monochrome strips individually.

Product is no longer available to order - contact us

Input-output extension module WBIO-DI-DR-8

This model is discontinued. WBIO-DI-WD-14 is a recommended replacement.
Designed for connecting pulse counters, buttons, switches and sensors with dry contact type intput.

Product is no longer available to order - contact us

Gas sensor WB-MSGR

This model is deprecated. Do not place it in your projects. Availiable for order until 30 June 2019
Electrochemical gas detection sensor WB-MSGR with built-in relay. The sensor is a leak detection tool and is not suitable for accurate measurement of gas concentration.

Product is no longer available to order - contact us

Input-output extension module WBIO-DI-DR-14

This model is discontinued. WBIO-DI-WD-14 is a recommended replacement.

Designed for connecting pulse counters, buttons, switches, sensors with a dry contact output.

Product is no longer available to order - contact us

WB-MSW wall sensor

Modbus sensor WB-MSW wall sensor

This model is discontinued. WB-MSW v.3 is a recommended replacement
Hybrid digital sensor of temperature, humidity, lighting, noise level and CO2 concentration. Designed for climate control in residential and office premises.

Product is no longer available to order - contact us

Input-output extension module WBIO-DI-DR-16

This model is discontinued. WBIO-DI-WD-14 is a recommended replacement.

Designed for connecting pulse counters, buttons, switches, sensors with a dry contact output.

Product is no longer available to order - contact us

Input-output extension module WBIO-DI-LVD-8

This model is discontinued. WBIO-DI-WD-14 is a recommended replacement.
Input of discrete signals, circuit integrity monitoring, etc.

Product is no longer available to order - contact us

Input-output extension module WBIO-DI-LVD-16

This model is discontinued. WBIO-DI-WD-14 is a recommended replacement.
Input of discrete signals, circuit integrity monitoring, etc.

Product is no longer available to order - contact us

Input-output extension module WBIO-DIO-TTL-8

This model is deprecated. Do not place it in your projects.
Designed for connection of devices with 5V TTL or 5V CMOS signals. Consists of 8 I/O 5V voltage channels configured as output by default

Product is no longer available to order - contact us

Комплектующие Polyfuse

By default, the controller is equipped with a fixed polyfuse. It can be replaced with the removable option. The power filter is plugged into the same connector

Product is no longer available to order - contact us

Extension module WBE-AO-10V-2

Dual-channel module with 0-10V analog outputs. Works with Wiren Board 5. Plugs into a connector on the controller board

1 500 ₽

Extension module WBE-DI-DR-3

Works with Wiren Board 5. Plugs into a connector on the controller board.

700 ₽

Extension module WBE-DO-OС-2

Works with Wiren Board 5. Plugs into a connector on the controller board

700 ₽

Extension module WBE-DO-R6C-1

Consists of a single SPDT (changeover contact) relay. Maximum current for resistive load: 6a for 230VAC or 30VDC. Works with Wiren Board 5. Plugs into a connector on the controller board.

700 ₽

Extension module WBE-DO-SSR-2

Consists of two SPST (normally open) optorelays with a single common contact. Current up to 400 mA, voltage up to 40VDC. Switch-on resistance < 2 Ohms Equipped with 40V TVS diodes for transient overvoltage protection when switching inductive loads.

700 ₽

Extension module WBE-GPS

Works with Wiren Board 5. Plugs into a connector on the controller board. Determination of coordinates. Standard time signal.

1 900 ₽

Extension module WBE-I-1WIRE

Auxiliary 1-Wire port. Works with Wiren Board 5. Plugs into a connector on the controller board.

700 ₽

Extension module WBE-I-CAN-ISO

Plugs into a connector on the Wiren Board 5 controller board.

1 200 ₽

Extension module WBE-I-KNX

Installed in the extension module connector in the controller enclosure

5 000 ₽

Extension module WBE-I-RS232

Works with Wiren Board 5. Plugs into a connector on the controller board. If you install the module on your own, please keep in mind the potential risk of improper installation or breakage.

700 ₽

WBE-I-RS485-ISO

Extension module WBE-I-RS485-ISO

Auxiliary galvanic isolated RS-485 port. Works with Wiren Board 5. Plugs into a connector on the controller board.

1 200 ₽

Extension module WBE-MICROSD

Works with Wiren Board 5. Plugs into a connector on the controller board

1 000 ₽

WBMZ-BATTERY-1800MAH

Battery module for Wiren Board 5 WBMZ-BATTERY-1800MAH

The module powers the controller itself, its extension and I/O modules and external devices connected via 5Vout and USB terminals. The WBMZ-BATTERY is installed as a second level into the controller enclosure and attached via ribbon cable to an internal connector. When the module is ordered together with the Wiren Board 5 controller as a set, the controller comes equipped with a shutdown button on the front panel. When the module is purchased separately, a controller front panel with the forced shutdown button is included in the delivery set.

2 200 ₽

Extension module WBE2-I-CAN-ISO

Installed in the extension module connector in the controller enclosure. This module is not compatible with Wiren Board version 5 and lower

Product is no longer available to order - contact us

Extension module WBE2S-R-433MHZ

This model has been discontinued. Software is discontinued. If you need this model, please contact us: info@contactless.ru.

Allows to control Noolite devices and some others, operating at a frequency of 433 MHz. External 433MHz antenna is included in the package. For Wiren Board 6. Inserts only in MOD3 connector on the controller board.

800 ₽

Power filter WBMZ-CAP

Для Wiren Board 5.

Product is no longer available to order - contact us

Legal purchase terms

General provisions

1. These terms of sale is developed on the basis of the RF Civil code, RF Law on February 7, 1992 № 2300-1 "On consumer protection", decrees of the Government of the Russian Federation of September 27, 2007 № 612 "On approval of rules of sale of goods remote way" and other normative-legal acts. These rules regulate the procedure for retail purchase and sale of Goods through the online store, being a public offer addressed to individuals and legal entities ("Buyers").

2. the Buyer accepts the terms and conditions set out in these terms and conditions by placing an Order on the online store's website.
An order is considered to have been executed properly if the Buyer provides the Seller with the following information: the buyer's last Name, first Name, phone number, address to deliver the Product, Product name, quantity.

2.1. the Buyer grants the Seller the right to use all personal data transmitted in the Order in order to fulfill its obligations to the Buyer, form and develop a loyalty program for Buyers, and inform Buyers about the news of the online store. The right of use in these terms is understood as the Seller's right to: collect, record, systematize, accumulate, store, clarify (update, change), extract, use, depersonalize, block, delete, destroy data with the right to transfer such data to third parties without further notice to the Buyer.

3. when selling goods remotely, the Seller offers the Buyer services for the delivery of Goods by delivery Services. In this case, the specific delivery Service for each Order is determined by the Buyer when placing the order.
Delivery is available on weekdays from 9: 00 to 18: 00. Delivery times depend on the selected region and range from 1 to 14 business days (not counting the day of the order). The delivery period may be extended in cases stipulated by the delivery Service's operating rules. Delivery is carried out without demonstration. If you do not agree with the delivery terms, You have the right to cancel your order at any time before receiving it.
For more information about regional delivery rates, please visit the website of courier services: SDEK, KSE, EMS.
If the Buyer refuses the Product, the Buyer is charged the cost of delivery in accordance with the tariff in accordance with paragraph 21 of the Decree of the Government of the Russian Federation of 27.09.2007 No. 612 "on approval of the rules for the sale of goods by remote means".
When receiving the Product from the delivery Service, the Buyer must check the appearance of the product packaging (for the absence of deformation, opening). When receiving the Goods, the Buyer puts his signature in the delivery receipt in the box: "I confirm that the shipment was received in closed form, there are no external damages to the packaging, bandages, seals, and the weight of the shipment corresponds to the weight determined when it was received."
If any defects are found on The product packaging, the Buyer must make a note of this in the delivery box on the courier's receipt. After receiving the Order and putting the signature of the Buyer in the receipt in the delivery column without specifying claims to the appearance of the product packaging, claims to external packaging defects (its opening and possible incompleteness of the Product) are not accepted.

4. Payment for ordered Products is made:
By Bank transfer on the invoice issued for the Buyer.A plastic card based on the link generated for the Buyer.

5. Order processing is made in the working days from 10:00 to 18:00 Moscow time. If you place your order after 18:00 Moscow time, our managers will contact you on the next business day after 10:00 am.

6. the Product is of good quality, you can return it within fourteen days from the date of receipt of the Order, provided that the product has not been used.
To do this, you need to write an email with a request for a refund/exchange to info@contactless.ru.
Please note that if the Buyer refuses the Product, the Seller returns the amount paid by the Buyer for the Product, with the exception of the Seller's expenses for delivery of the returned Product from the Buyer, no later than 10 days from the date of submission of the corresponding claim.

7. the Warranty period for the Product is set at 24 months from the date of shipment.

8. the Risk of accidental loss or accidental damage to the Product passes to the Buyer at the time of transfer of the Product and the Buyer's signature in the documents confirming the delivery of the Order. Ownership of the Product passes to the Buyer at the time of transfer of the Product, subject to full payment.

9. the legislation of the Russian Federation applies to the relations between the Buyer and the Seller.

10. the Seller reserves the right to make changes to these terms of sale, and therefore the Buyer undertakes to regularly monitor changes in the Rules posted on the website of the online store. The Seller must post a notice of changes to these terms of sale no later than 7 (seven) calendar days before their effective date.

11. the Buyer guarantees that all the terms of these terms of sale are clear to him, and he accepts them unconditionally and in full.

12. the Invalidity of any provision of these Rules does not entail the invalidity of the remaining provisions.

13. all disputes arising between the Parties will be resolved through negotiations. if an agreement is not reached, the dispute will be referred to the arbitration court of Moscow in accordance with the current legislation of the Russian Federation.